ICP DAS USA TPD-433-H User manual

TPD-433-H 4.3" Touch Screen Controller - QuickStart (Apr/2020)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 1
TPD-433-H
4.3" Touch Screen Controller
Quick Start
What’s in the box?
Thanks for buying ICPDAS TPD-433-H/433-H-EU device.
This shipping package contains the following items:
TPD-433-H x 1 Quick Start x 1 (This Document)
PET Film Screen Protector
Back Piece x 1
57 mm x 98 mm x 1
Related Information
Documents, such as the User Manuals, the API References,
etc.: https://www.icpdas-usa.com/tpd_433_h.html
Free Development Software, HMIWorks:
https://www.icpdas-usa.com/hmiworks.php
If you have any questions, please feel free to contact us via email.

TPD-433-H 4.3" Touch Screen Controller - QuickStart (Apr/2020)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2
1Appearance
Front View
Rear View
4.3” TFT LCD with Touch Panel
Rotary Switch
Serial Port
LED Indicator
Buzzer
Ethernet USB
2Pin Assignments
Pin
Description
F.G.
Frame Ground. F.G. is connected to the inside EMI or ESD
suppression circuits. Make sure that F.G. is connected to the
Earth
VDC
DC input Voltage (range: +12 V ~ +48 V)
GND
Connected to the power supply’s ground pin
DATA+
The positive data line of the RS-485 network
DATA-
The negative data line of the RS-485 network

TPD-433-H 4.3" Touch Screen Controller - QuickStart (Apr/2020)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 3
3Rotary Switch & Default Settings
The definition of the rotary switch:
No
Mode
Description
Run &
This is a special run mode which is used in
the development stage. The TouchPAD
0
Update
device can be updated by a PC from the
(Ethernet)
remote side through Ethernet. (Default)
Ethernet
While the application run on the TouchPAD
1
Force
device seriously crashes, use this mode to
Update
update a new application to the TouchPAD
device through Ethernet.
2
Run Only
Run the program.
9
USB Force
Update a new application to the TouchPAD
Update
device through USB.
Network Default Settings
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4First Use of the TPD-433-H(-EU)
1. Connect wires as the below figure or prepare an Ethernet cable
which will be used to supply power through PoE if there’s a RJ-45
Ethernet port on it. And set the rotary switch to 0 (At this point, the
power is not yet supplied).

TPD-433-H 4.3" Touch Screen Controller - QuickStart (Apr/2020)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4
PoE Switch
GND
VDC (+12-+48 V)
Use a flat-head screwdriver to set rotary switch
External Power
2. Supply power to the TPD-433-H(-EU),
wait for several seconds and then you
can see the default program run on it.
3. Try to touch on the icons on the bottom-right corner of the screen of
the TPD-433-H(-EU) and you can find that TPD-433-H(-EU) switches
to the setting pages.

TPD-433-H 4.3" Touch Screen Controller - QuickStart (Apr/2020)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 5
5 Hardware Installation
TPD-433-H-EU with
TPD-433-H with Outlet Box,
TPD-433-H with External
European
OB120 (optional)
Wall Box EWB-T43
86 mm x 86 mm Outlet Box
(optional)
hgjgh