ICP DAS USA PEX-P64 Series User manual

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The package includes the following items:
One PEX-P64(-24V) and PISO-C64U(-24V) PCI Board.
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
One CA-4037B Cable
Two CA-4002 D-Sub connectors
For PEX-P64/PISO-P64U Series
What’s in the shipping package?
English/ Oct. 2013/ Version 1.1

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
The PISO-DIO Series classic driver supports Windows 98/NT/2K and 32-bit
XP/ 2003/ Vista/7/8. Recommended to install this driver for have been
used PISO-DIO series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/quickstar
t/classic/
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Installing Windows Driver

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Please make sure J1/J2/J3/J4 jumper is kept in default setting before self-test,
as follows: ( This example uses this power supply.)
Jumper
J1/J2/J3/J4
Internal Power

External Power
(Default Setting)
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI/PCI Express slot.
Step 4: Carefully insert your I/O card into the PCI/PCI Express slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
Installing Hardware on PC
Jumper Setting

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Extension Cable (CA-4037B):
DB-40-Pin conversion DB-37-Pin
Pin Assignments

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Prepare for device:
DN-37 (optional) wiring terminal board.
Exterior power supply device. For example: DP-665 (optional)
Self-test wiring as follows:
1. Use the DN-37 to connect the CON1 on board.
2. Keep set the J1 jumper to External Power (Page 3).
PEX-P64 and PISO-P64U External Power Wiring:
3. Power Supply (+5 V) connect to ECOM0 (Pin18).
Power Supply GND connect to IGND0 (Pin1).
IGND0 (Pin1) connect to DI7 (Pin9).
PEX-P64-24V/PISO-P64U-24V External Power Wiring:
3. Power Supply (+24 V) connect to ECOM0 (Pin18).
Power Supply GND connect to IGND0 (Pin1).
IGND0 (Pin1) connect to DI7 (Pin9).
Self-Test
The PEX-P64/PISO-P64U suggests input voltage range as follow:
Logic high: +5 ~ +15 V (Max. 24 V); Logic Low: 0 ~ 1V.
(Higher voltage over the limitation will cause the hardware damage.)
The PEX-P64-24V/PISO-P64U-24V suggests input voltage range as
follow: Logic high: +20 ~ +28 V (Max. 30 V); Logic Low: 0 ~ 1V.
(Higher voltage over the limitation will cause the hardware damage.)

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The PEX-P64/PISO-P64U wiring is illustrated in the figure below:
The PEX-P64-24V/PISO-P64U-24V wiring is illustrated in the figure below:

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
4. The UniDAQ Utility.exe is located in:
This program (UniDAQ Utility) will be placed in the default path after completing
installation.
Default Path: C:\ICPDAS\UniDAQ\Driver\
Double click the “UniDAQUtility.exe”
5. Execute the UniDAQ Utility Program.
Double-Click
1
Confirm the PISO-P64 series card had
successfully installed to PC. It starts from 0.
2
Click this button
to start test.
3

PEX-P64/PISO-P64U Series Quick Start Guide ICP DAS CO., LTD.
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
6. Get DI function test result.
PEX-P64 and PISO-P64U Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-p64.html
DN-37, CA-3710 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information
Select the “Port 0”.
The Corresponding DI becomes black for
channel 7 of DI7 is ON. The other DI0 to DI6
should become red because the DI0 to DI6 is
OFF (Not wiring).
6
5
Click “Digital Output” item.
4
PASS
Port0: DI0-7
Port1: DI8-15
Port2: DI16-23
Port3: DI24-31
Port4: DI32-39
Port5: DI40-47
Port6: DI48-55
Port7: DI56-63