idi Aspect Q-CARD 100-4T User manual

IMAGING END
OF TABLETOP
Aspect 100-4T Q-CARD
SETUP/PATIENT PREPARATION:
Moving table (NEVER WITH PATIENT ON BOARD):
1) Unlock Rear Casters using Caster Lock Pedal.
2) Unlock Front Steering using Front Steer Lock Pedal.
3) Position table to desired location.
4) Secure table mobility by locking Casters and front steering
using Rear Caster Lock Pedal and Front Steer Lock Pedal.
AC Power:
5) Plug power cord into properly grounded outlet.
6) Protect power cord from damage by casters or other
equipment.
Controls:
1) Emergency Stop Pushbutton disables all tabletop motion
control when engaged.
2) If tabletop motion controls fail to operate, make sure
that the Emergency Stop Pushbutton is NOT pushed in.
BATTERY OPERATION (DC POWER):
1) The table is FULLY functional, but motions are slower.
2) Connect to AC power for a minimum of 8 hours daily to
ensure a proper battery charge.
3) Failure to push in Emergency Stop Pushbutton when table
is not in use and not connected to AC power for longer
than 72 hours, may result in permanent damage to the
batteries.
CPR:
Return table to level, retract tabletop to minimize
overhang and lower table position to a comfortable
height to perform CPR.
CLEANING AND STORAGE:
1) Unplug power cord and wrap it around
the cord holder.
2) Push in Emergency Stop Pushbutton.
3) Lock rear casters and front steering.
4) Clean and disinfect table.
WARNING! Read operator
manual prior to use
CONNECTION PORT FOR HAND
OR FOOT CONTROLS CONNECT
HERE
EMERGENCY
STOP
PUSHBUTTON
REAR CASTER LOCK PEDAL
BRAKES:
The 100-4T table braking system utilizes a passive magnetic brake;
it remains engaged in the event of a complete loss of electrical
power. Power is necessary to release brakes.
Braking force is limited by the magnet strength. Use caution when
applying pressure to the side of the table as the brakes may be
overcome if more than 50 pounds of force is applied.
To reduce potential motion during patient transfers with larger
patients, release the table brake and move the top in the direction
the patient will be pulled during loading or unloading until the
tabletop transverse travel limit is reached. Release the panning
handle to re-engage the lock and then transfer the patient.
POWER CORD
HOLDER
PEDESTAL END OF TABLETOP
Scan to
Access
User
Manuals
Online
FRONT STEER
LOCK PEDAL

It is recommended that the pendant
control be disconnected during critical
procedures to prevent inadvertent
operation or motion, causing patient
injury.
•PUSH IN to stop
ALL tabletop motion.
•TWIST to reset.
ELEVATE
SWITCH
TRENDELENBURG
SWITCH
PANHANDLE
KNOB/ TABLETOP
FLOAT BRAKE
(Lift underside of
Panhandle Knob to
float tabletop. It will
not operate if
tabletop is not level)
L100-2912 Rev.F
Tabletop Motion
Handset Control
Patients must be loaded from the side of table. Tilting or instability may occur if
patient is loaded onto the pedestal end of table or the imaging end of the table.
EMERGENCY STOP PUSHBUTTON
(Green light to
right of Tabletop
Float Brake
indicates tabletop
is centered on the
base laterally)
TABLETOP MOTION
CONTROL PANHANDLE
Elevate
Tilt up Imaging
End
(Trendelenburg)
Trendelenburg
Level Indicator
Laterally Centered
Indicator
Lower
Tilt Down
Imaging End
(Trendelenburg)
Aspect 100-4T Q-CARD
CASTER LOCK/STEER
PEDAL POSITIONS
UNLOCK
PRESS DOWN ON BOTTOM HALF
OF PEDAL TO ALLOW REAR
CASTERS TO SWIVEL FREELY
LOCK
PRESS FORWARD ON TOP HALF
OF PEDAL TO LOCK ALL
MOVEMENT
OF REAR CASTERS
(Green light to right of
switch indicates tabletop is
level for this motion)
STEER LOCK
PRESS DOWN ON PEDAL TO
RESTRICT FRONT MOVEMENT TO
FORWARD AND BACKWARDS ONLY
FLOAT POSITION
PULL UP ON PEDAL TO ENABLE
MOVEMENT OF FRONT IN ALL
DIRECTIONS