idi Aspect100US User manual

Operator Manual Aspect 100US
Made in the USA
Aspect100US
Gyn/Fertility Mobile Imaging Table
Operator Manual

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com ii
Table of Contents
PRODUCT DATA ............................................................................................................................................ 1
INTRODUCTION ............................................................................................................................................ 2
CUSTOMER SUPPORT ................................................................................................................................... 3
SYMBOLS AND DATA PLATE......................................................................................................................... 4
SPECIFICATIONS............................................................................................................................................ 6
ELECTROMAGNETIC COMPATIBILITY STATEMENT...................................................................................... 7
SETUP ............................................................................................................................................................ 8
SAFETY HAZARDS.......................................................................................................................................... 9
SAFETY HAZARD ALERTS ............................................................................................................................ 10
SAFETY INSTRUCTIONS............................................................................................................................... 10
ACCESSORIES ..............................................................................................................................................13
ELECTRIC SYSTEM .......................................................................................................................................15
CONTROLLER CONNECTIONS .....................................................................................................................16
BATTERY FUNCTION ...................................................................................................................................16
GENERAL CLEANING ................................................................................................................................... 17
MAINTENANCE ........................................................................................................................................... 18
USER REPLACEMENT ITEMS ....................................................................................................................... 19
TROUBLE-SHOOTING.................................................................................................................................. 19
DISPOSAL OF COMPONENTS...................................................................................................................... 20
WARRANTY................................................................................................................................................. 21
Linak documentation can be found at their web site: www.linak-us.com
Select “Products | User manuals” and click on “Actuators & Electronics”.
The text of this manual was originally written, approved
and published by the manufacturer in English.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 1
PRODUCT DATA
•Low attenuation carbon fiber tabletop
•Tabletop: 61 cm x 117 cm (24 in x 46 in)
•Imaging area: 61 cm x 117 cm (24 in x 31 in)
•Height range: 66 cm to 101 cm (26 in to 38 in)
•Patient capacity: 204 kg (450 lbs)
•Table weight: ~177 kg (~390 lbs)
•Locking swivel casters
•Low attenuation table pads
•Foot operator control

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 2
INTRODUCTION
Overview
This manual pertains to the specified product only. It is intended for qualified medical
personnel who have been trained in the use of medical equipment. It is not designed to
replace or substitute for certified training in the application of this equipment.
Functional capabilities and operation of the equipment described herein which can be
employed in a variety of diagnostic, therapeutic, and surgical applications. It is designed
for use as either a fluoroscopic or radiographic table.
Owner Responsibilities
The owner is responsible to ensure system compatibility, the qualifications of the
operator and maintenance personnel. The operator must be properly trained and have
obtained credentials from the appropriate authorities.
This equipment should only be installed in an area provided with the proper electrical
power.
The owner is responsible for verifying continued compliance with all applicable
regulations and standards. Consult local, state, federal and/or international agencies
regarding specific requirements and regulations applicable to the use of this equipment.
Image Diagnostics, Inc. certifies this equipment. After-sale operating practices and safety
are the responsibility of the owner and operator. Image Diagnostics, Inc. assumes no
liability or responsibility for after-sale operating or safety practices; nor can it be
responsible for personal injury or damage resulting from misuse.
Never make modifications or adjustments to the equipment unless directed by a qualified
Image Diagnostics representative. This equipment, when properly assembled, meets US
federal regulations and international standards. Unauthorized modifications to the
equipment may impact adherence to these standards and make the equipment unsafe to
operate.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 3
CUSTOMER SUPPORT
Image Diagnostics will make available, on request, circuit diagrams,
component part lists, calibration instructions, or other information which
will assist the user’s appropriately qualified technical personnel to repair
those parts of equipment which are designated by the manufacturer as
repairable.
For technical assistance, call IDI at [phone] or send fax to (978)
829-0027. Be prepared to give the complete model and serial number
found on the dataplate on the table base at the time of contact.
This X-ray component manufactured by Image Diagnostics, Inc. complies
with applicable FDA performance standards contained in 21CFR at date of
manufacture.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 4
SYMBOLS AND DATA PLATE
Intertek Testing Service
The system was tested and found to be in compliance with the
requirements of all relevant directives and standards in effect within
the European Union at the time of manufacture.
Attention! Consult accompanying documents.
Failure to follow these instructions can cause accidents resulting in
serious personal injury or damage to equipment. CD ROMs
containing file copies of all relevant drawings, BOMs, and
documentation are included with this manual, one for general
operators and one for the BIOMED department.
Type B equipment
Alternating current
Data Plate
Maximum Patient Weight
Equipotential Terminal (Featured on some models)
Indicates the Equipotential terminal of the table. Provides for a
connection between the table and the equipotential bus bar of the
facility.
204 kg
450 LBS

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 5
LATEX
Recycle
Some of the material can be recycled rather than discarded.
Not for Patient Transport
The table should not be relocated with a patient on it nor should it
be used to move a patient.
Do Not Sit
This label is found on parts that are not designed to support the
sitting weight of a patient.
Not made with natural rubber latex
This symbol, when used in this manual, indicates the potential of
exposure to harmful x-rays. Be sure to read and comply with all
warnings.
European Authorized
Representative
Warning! Information or instructions shown near this symbol must
be adhered to in order to prevent a potentially hazardous situation
which if not avoided, could result in death, personal injury or
damage to the equipment.
Protective Ground
This is the common tie point between the AC cord ground, frame
ground, and controller ground.
EC
REP
Advena Ltd. Pure Offices, Plato Close,
WARWICK CV34 6WE UK

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 6
SPECIFICATIONS
Mode of Operation:
For continuous operation with short time loading
Duty Cycle: 10% (6 min/hr)
Type of Equipment:
Class I Type B (as defined by IEC 60601-1, UL 60601-1,
EN 60601-1, CSA 601.1, IEC 60601-2-32:1994 and IEC 60601-2-46)
Type B protection against electrical shock
Complies with FDA standards
Electrical:
Supply Voltage: 120±5% Vac 60Hz or 23010% Vac 50Hz
Duty Cycle: 10% (6 min/hr)
Current Rating: Less than 10 Amps
Internally Battery Powered
Environmental:
Operating Temperature Range: -10C to +40C
Operating Humidity Range: 30% to 75% relative humidity, noncondensing
Operating Pressure Range: 700hPa to 1060 hPa
Transport & Storage Temperature Range: -40C to +60C
Transport & Storage Humidity Range: 30% to 75% relative humidity, noncondensing
Transport & Storage Pressure Range: 500hPa to 1060 hPa
Rated IPX4 (Protected against splashing water)
Meets EMC requirements of EN 60601-2 (1993)
Tabletop:
The tabletop is made of carbon fiber and is certified to meet all the requirements of 21
CFR Subchapter J

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 7
ELECTROMAGNETIC COMPATIBILITY STATEMENT
This equipment may generate and use radio frequency energy. The equipment must be
installed and used according to the manufacturer’s instructions in order to avoid radio
frequency interference.
If this equipment generates or receives interference:
•Verify that the equipment is the cause by turning the system off and on.
•In the event of unintended motor actuation, immediately remove power to the
equipment.
•Use only cables supplied by Image Diagnostics, Inc.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 8
SETUP
Unpack
No special handling is required for unpacking this equipment at the site. Conventional
shipping materials are used.
To remove the table from the shipping pallet, first remove the shipping brackets that
secure the table to the wooded pallet using a ½” wrench. Then roll the table down a
temporary ramp or lift off pallet with a forklift. When using a forklift, pad the forks to
protect the paint. Lift from under the metal base. When rolling the table off the pallet by
hand, use the long metal rails attached to the tabletop to guide the table after releasing the
caster brakes.
Install
Mobile tables are equipped with four locking caster brakes. Unlock brakes while positioning.
Foot controls are standard with this table. The operator should become familiar with the controls
before using.
The table operates on 110Vac (or 230Vac) or on internal battery backup. Swing the hinged cover
open to find the power cord on some models. Plug the AC power cord into a properly grounded
hospital grade outlet. The green indicator on the control box with illuminate, however, the hinged
cover will need to be opened to see the green indicator.
The outlet used should be visible and accessible to the user. The cord should be routed where it
will not be subject to damage or be a hazard. Check that the power cord ground pin is in good
condition. Check that the cord ground wire is securely connected to the ground stud inside the
unit.
Recycle or dispose of shipping
material per local regulations.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 9
During an AC failure, the table will automatically run on battery backup without any manual
switching required. It is recommended that power be applied at all times, even when not in use, to
keep a proper charge on the batteries and achieve maximum battery life. (Batteries are being
charged during normal use).
Where the integrity of the external protective earth conductor is in doubt, this equipment shall be
operated from its internal electrical power source by unplugging the power cord from the mains.
Preparation for Patient Use
New Installation:
This equipment will need to be properly cleaned before patient use as it will inevitably come into
contact with contaminants during shipping, unpacking, storage, and installation.
After Installation:
This equipment will need to be properly cleaned between patient use as it will inevitably come
into contact with contaminants during procedures.
SAFETY HAZARDS
Operators using this equipment should understand the safety issues, emergency
procedures, and operating instructions provided.
Comments and questions regarding safety should be addressed to:
Customer Support
Image Diagnostics, Inc.
310 Authority Drive
Fitchburg, MA 01420
USA
Or call IDI at [phone] or send fax to [phone].
Or call toll-free at [phone].
Review the SAFETY INSTRUCTIONS before
operating table

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 10
SAFETY HAZARD ALERTS
Alert
Circumstances for Use
DANGER
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentiallyhazardous situation which, if not
avoided, may result in minor or moderate injury or
equipment damage.
WARNING!
This equipment has not been tested for use with high
frequency surgical equipment, cardiac defibrillators, or
cardiac defibrillator monitors.
WARNING!
If an antistatic path is required, use the equipment on an
antistatic floor. Use only the tabletop pad (patient
mattress) supplied with the table.
WARNING!
This product may be used in conjunction with x-ray
equipment. This constitutes potential expose to harmful
x-rays for both the patient and operator. Be sure to use
proper radiation shielding.
CAUTION
Secure power cord when in use so that it does not get
entangled with other equipment and/or compromise
the safety of the operator and/or staff.
CAUTION
Do not modify this equipment without authorization of
the manufacturer.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 11
SAFETY INSTRUCTIONS
This manual should be accessible to all personnel installing, operating, or servicing this
equipment.
Only a qualified technician may install or maintain this equipment.
Only qualified persons may operate this equipment.
Failure to follow safety precautions may result in serious injury to patient or user or damage to
equipment.
This symbol, when found marked on the equipment
means:
”Attention, consult accompanying documentation.”
WARNING!
Always safely position and secure patient on table
WARNING!
Do not exceed patient weight of 450 pounds (204kg)
CAUTION
Do not leave patient on table unattended
CAUTION
Patient must be restrained at all times. The restraining
straps are not intended to restrain an uncontrollable
patient.
CAUTION
The carbon fiber top is subject to damage or possible
damage from impact from other objects. Take caution
when using power driven diagnostic equipment around
table. Regular inspection of the tabletop is necessary for
the safety of patient and operator.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 12
Push down to lock
CAUTION
Ensure that the tabletop does not contact other
equipment as it moves.
CAUTION
During operation, listen for any unusual sounds and
watch for uneven operation.
CAUTION
If using legholder stirrups with this table, use
caution. The boot will drift if the clamp is not securely
tightened. Note: there is a left and a right boot.
CAUTION
Do not sit at the head of the table.
CAUTION
Do not place or store any containers or large items
underneath the tabletop. As the tabletop is descending,
contact with an obstruction may cause permanent
damage to the table.
CAUTION
Do not use table for patient transport.
CAUTION
Secure wheel locks by depressing locks on all 4
wheels prior to patient usage and when table is not
in motion. Disengage to reposition.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 13
ACCESSORIES
•PATIENT RESTRAINT STRAPS
Hook & loop fasteners
Patient Restraint Strap Set
Part Number C000-0571
(Two straps 3” wide)
•STIRRUPS
Stirrups Accessory Clamps (to mount stirrups to accessory rail )
Part Number C000-0745 (pair) Part Numbert C000-0746 (order qty 2)

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 14
•ARMBOARD (OPTION)
To install clamp to tabletop:
- Turn knob counterclockwise (as viewed from above) to open clamp enough
to slip onto tabletop
- Turn knob clockwise to tighten clamp to tabletop
AB
C
D
E
A –Push to open latch to install or remove
B –Patient’s arm weight locks unit in place
C –Patient hook & loop arm straps
D –Pad
E –To rotate, lift end of armboard and move to desired location
Armboard with Pad & 2 Straps #A310-057 (Qty. 1, fits left or right side of table)
Replacement Armboard Pad #A100-1073 (Qty. 1, fits left or right side of table)
Replacement Armboard Straps #C000-0455 (Pair, fits left or right side of table)
WARNING!
25lbs (11kg) Maximum Load

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 15
ELECTRIC SYSTEM
B
D
A
E
C
F
A –AC Power Cord
B –Control Box (controller, batteries and battery fuse inside)
C –Power On Indicator
D –Safe DC Voltages
E –Elevating Actuator
F –Foot Control

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 16
CONTROLLER CONNECTIONS
B
A
5
4
3
1
2
Pull tab to access input fuses and spares
(use forceps to pull out spares)
PORT
DEVICE
1
ACTUATOR
A
FOOT CONTROL
BATTERY FUNCTION
When the AC power cord is plugged into the wall, the battery will be charging until the
battery reaches full capacity. When it does, the charging will taper off. If the power at
the outlet goes out, or the power cord is unplugged, the table will automatically switch to
battery back-up mode.
Local procedures may be in place for proper disposal or recycling.
For more information about batteries, such as battery life, production
codes and disposal go to the Linak web site for disposal information.
Select “Products|User Manuals” and click on “Actuators & Electronics”.
Linak documentation can be found at their web site: www.linak.com

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 17
GENERAL CLEANING
After each procedure, the table should be carefully cleaned
The disinfectant cleaners and cleaning steps on this page apply to all the parts of the
table, except the lift column.
• Clean tabletop, pads, accessories, and painted surfaces with a clean cloth dampened
with an approved cleaner (see list below).
Do not use abrasives, solvents, sprays, or corrosive agents.
APPROVED AND TESTED DISINFECTANT CLEANERS
•Sodium hypochlorite (generic household bleach) in solution of 5.25% sodium hypochlorite
diluted between 1:10 and 1:100 with water.
•Alcohol (generic)
• Envirocide ® Disinfectant and Cleaner
CLEANING STEPS
1. Lower the tabletop to the lowest position.
2. Power cord must be plugged in to protect the socket.
3. Remove any accessories.
4. Wipe off any access fluids with a water dampened cloth or sponge.
5. Clean any accessories, tabletop and frame using an approved cleaner.
6. Thoroughly rinse tabletop pad with water.
7. Gently rub with a soft clean cloth to dry.
If noise or uneven motion occurs when the table top is moving up or down, extend
and clean the lifting tube with a soft clean cloth.
CAUTION
Avoid cleaning or getting cleaning solutions on
elevating tube if possible.

Operator Manual Aspect 100US
L100-3060 REV A www.imagediagnostics.com 18
MAINTENANCE
”Qualified Technician”
•All maintenance procedures should be done by an experienced technician with demonstrated
knowledge and skills (electrical and mechanical) relative to this type of equipment.
•This individual must have access to this manual and the proper tools.
ROUTINE MAINTENANCE
• Lubrication is not required however powdered graphite may be used on the lifting tube.
PERIODIC PERFORMANCE CHECKS
•Semiannually perform functional inspections of carbon fiber tabletop, support frame,
and the elevating tube.
• Daily inspect all external cables, controls, and the tabletop for wear and damage.
Replace damaged cables promptly.
• Weekly check battery operation by disconnecting the AC power and running the tabletop
up and down.
Check daily if table is routinely used without being attached to mains.