idi Ilex 55 User manual

Made in the USA L280-0974 REV A
Installation Guide
For units using MSV2 video signal router
The text of this manual was originally written, approved and published by the manufacturer in English. The information and
images in this document are proprietary to IDI and is only for use for and by IDI representatives or their Agents.

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page i
Table of Contents
System Components ilex55............................................................................................................. 1
Other ilex feature programming...................................................................................................... 1
Video Inputs.................................................................................................................................... 3
Factory Preset Layouts.................................................................................................................... 5
Accessing Onscreen Keyboard....................................................................................................... 7
Modifying Layouts.......................................................................................................................... 7
Assigning Channels to Window Location ...................................................................................... 9
Cropping Windows....................................................................................................................... 10
Rename Layouts and Channels..................................................................................................... 11
Saving and returning to guest mode.............................................................................................. 11
Monitor Menu Navigation ............................................................................................................ 12
General Cleaning .......................................................................................................................... 16
Large Monitor Cleaning FSN monitors only............................................................................ 16
Large Monitor Cleaning Barco Only........................................................................................ 18
Barco Tablet cleaning ............................................................................................................... 18

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 1
System Components ilex55
Power Switches
In the event power switches have been toggled “OFF”, please use the following to turn power on to the different
components. To power up the monitor there is a switch located on the rear of the monitor where video inputs
are. To power up the MSV2 4k reach behind the tray on the top shelf on the right side of the box and there is a
power on/off switch. The touchscreen monitor has a power button on the bottom of the unit, press and hold to
turn on. Under normal use these buttons can stay in the “ON” position.
Other ilex feature programming
ilex55 system On/off Button, use the green toggle switch/thermal breaker to turn the system
on and off and to reset the breaker.
Up/Down switch, use the monitor elevation toggle switch to adjust monitor
height.
When the red emergency stop button is pushed in, elevation of the monitor is not allowed. Always
push the red emergency stop button when moving the ilex55 to reduce the risk of damage to
the unit. Reset by rotating the button a quarter turn.
19in x 28in
[48cm x 71cm]
20in x 20in
[50cm x 50cm]
12in
31cm
9in
22cm
16in
40cm
92in
72in
233cm
182cm
301
2"
77cm
31"
790mm
55in
140cm
ACROSS
HANDLES
353
4"
910mm
ilex55 Mobile Video Display System
IMAGE DIAGNOSTICS, INC.
Maximum duty cycle of the actuator is 10% or 2 minutes of continuous use followed
by 18 min. not in use. Exceeding this limit could damage the device and require
replacement.
Emergency Stop
Master
On/Off
Up/Down
Touch Screen Controller
Blue Tooth Speaker Pairing
Caster Break
Float and Steer
Video Scaling
(under cover)

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 2
To use the speakers with an external audio device with Bluetooth® capability, perform the
following steps: 1. Ensure that the green toggle power switch is on and lit up.
2. On the cart’s audio control panel, ensure that the “INPUT SELECT” switch is set to “BT.”
3. Turn the power on to the Cart’s audio system by turning the rotary Volume Control knob
clockwise so that the red PWR light lights up.
4. If the system doesn’t automatically sync, press in the white Volume Control knob button and
hold it in for 3 seconds (or until the 'BT' Bluetooth® indicator light begins to blink. (You may
also hear the system prompt say 'Power ON').
5. Turn on a Smart Device and locate a list all available Bluetooth devices. The Network Name
will appear as 'BT-RY' on your Smart Device list. No password is required to connect, but if
you are prompted, enter '0000' (4 zeroes).
6. As the Smart Device and the cart are synchronizing, the LED indicator light on the cart will
blink progressively quicker and you will hear the system prompt 'Paring.'
7. When a successful connection is established, the LED indicator light on the cart will stay lit
without blinking and you will hear the system prompt, 'Your device is connected', indicating
that the unit is ready to transmit audio.
(Note: Audio Devices can also be connected to the Cart using cables that have a 3.5mm Aux Jack or a ¼in.
Microphone Jack. Move the “Input Select” switch to the corresponding format and adjust the volume as
desired.)
Speaker covers are magnetic and can be easily removed for cleaning
The ilex55 is equipped with a castor motion locking system for transport and clinical
operation.
Free Float –The middle position of the castor locking pedal
(horizontal to floor) allows for movement of the ilex55 in any
horizontal direction.
Total Lock –Step down on the pedal’s red pad to lock all
horizontal movement of the ilex55. Step down on the pedal’s
green pad to return to the Free Float position.
Steer Lock –Step down on the pedal’s green pad to lock the
steering direction of the 2 casters on the opposite side of the
pedal. Step down on the pedal’s red pad to return to the
Free Float position.

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 3
Video Inputs
The ilex55 has 4 different channel input capabilities
Video inputs are connected to the rear of the ilex55 then routed scalers and into the controller, the MSV2
(Multiview scalar). Basic Layout navigation is done in the “Guest” mode of the system. Changing or
programing of the layout format is available only in the “Administrator” mode.
Video Panel on rear of ilex55
Channel 1 inputs: DVI, VGA, or S-Video
Channel 2 inputs: DVI, or VGA or SDI(using DVI to DVI jumper from SDI panel)
Channel 3 inputs: DVI, DisplayPort, or SOG
Channel 4 inputs: DVI, DisplayPort, or SOG

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 4
Basic “Guest” mode
Administrator mode
Screen
Layouts
Single
Channel
Inputs

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 5
Factory Preset Layouts
By design each preset has the capability of showing 4 windows, A, B, C, & D. Each of the windows can be
cropped, resized, relocated, and assigned one of the 4 channel inputs. Channels 3 & 4 can also accept
DisplayPort video inputs when required. Channels 1 and 2 are HDMI inputs only.
There are 8 preset layouts as shown below. There is also single channel layout which displays each of the four
channels at full screen.

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 6
For each of the preset layouts the windows can be assigned channel 1,2,3 or 4.
Screens can be rotated clockwise or counterclockwise within a given layout.
Image Rotation buttons

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 7
Accessing Onscreen Keyboard
When a keyboard is not used it is still possible to bring up the onscreen keyboard.
1. Press and hold anywhere on the screen until the “x” appear at the top of the screen. Click on the “x”.
1.1. On the taskbar at the bottom of the screen, click on the icon that looks like a keyboard
1.2. Click on the icon in the top right of the keyboard to undock it. Now the
keyboard can be moved around the screen
1.3. Click in the bottom right of keyboard on the icon 123 to get the number
pad to appear
1.4. Click the “x” in the top right-hand corner of the keyboard to close it out
1.5. Once keyboard use is complete, click on the screen.
1.6. Click the three dots in the top left corner of the web browser
1.7. Click the square next to the zoom buttons to bring the monitor back into
Fullscreen mode.
Modifying Layouts
Log in as an administrator
2. To login as admin click in the top right corner of the screen, click the door with an arrow point right to sign out.
Connect keyboard to the tablet or access the on-screen keyboard as described in previous section.
2.1. Login in with the following credentials (case sensitive, and don’t
forget exclamation at end)
2.1.1. Username: admin
2.1.2. Password: 123123123!
2.2. To login as guest/operator mode use the following credentials
(case sensitive, and don’t forget exclamation at end)
2.2.1. Username: idi
2.2.2. Password: Password55
3. In general, always remember to Click apply and save, otherwise work will be lost.
3.1. There are 5 possible user set layouts that can be adjust the size, and location of windows (User0,1,2,3,4)
There are 3 program defined layouts that cannot be adjusted (Quad, 3Side, and 3 Bottom)
3.1.1. Start in Design mode (at the top of the page, 3rd tab, icon is 4 squares)

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 8
3.1.2. On the right side of the screen select the desired user in the drop-down
menu. Click on the new layout tab, then select one of the predefined
layouts with the correct number of channels required for layout.
Avoid looking at the live screen at this point as the images will be
scaled incorrectly, this will be autocorrected in the next few steps
3.1.3. Click save at the top
3.1.3.1. Note: Failure to click save will result in lost work
3.1.4. Re-arrange the windows using the following steps.
3.1.4.1. Click save, click in the desired window A, B, C, or D
3.1.4.2. Click and hold any corner of the desired window to change
window size. Note: if the window size becomes larger than the screen it will revert to its
original size.
3.1.4.3. Click and hold in the center of a window to drag location around the screen. Note: dragging a
window past the edge of the screen is not allowed and will return to its original location. In
most cases, change the size of the window to be smaller prior to moving the window around
the screen, then enlarge if needed.
3.1.4.4. Sizing and moving can also be done via numerical
data at the bottom of the page. See Coordinate
information. X & Y are the coordinate points
relating to the overall location of window in the
monitor. W and H are the width and height of the
desired window. Enter the height and width of the
window first, then adjust location. Values that are
invalid will revert to original state. If there is not
data in a given row, that signifies that window is not
active in the given layout.
3rd
1st

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 9
3.1.4.5. In the edit tab, set the layer requirements as needed
by clicking on the green box and selecting a layer
in the drop-down menu. L4 is considered the top
layer, L1 is bottom most layer.
3.1.4.6. To add a channel to a given layout click on the
letter in the edit tab and select turn on or off.
3.1.4.7. Click apply and save
3.1.5. Cropping may be required to make the image fill the
entire window. Since aspect ratio is turned on, the image may
not be correctly cropped/and or scaled. Cropping adjustments will be
made in the next few steps, after the channels have been designated to
the appropriate window locations.
3.1.6. Layout has been configured and now the channels can be assigned to window locations and channels
can also be cropped at this time.
3.1.7. Before changing tabs click apply and save, failure to do so will result in lost work.
Assigning Channels to Window Location
4. Each channel input 1,2,3,4 can be
assigned to a window, A, B, C, or
D. Channels can also be duplicated
on to different windows
4.1. Go to preset and channel mode
(2nd tab looks like slider
buttons)
4.2. Select QUAD, from the dropdown
menu
4.3. Change A to reference Channel 1,
B>CH2, C>CH3,D>Ch4
4.4. Click a different channel in row A,
notice the screen changes.
4.5. Assign channels to the appropriate window as needed.

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 10
Cropping Windows
5. Steps used to crop windows and channels
5.1. Go to Preset and channel mode (2nd tab,
pencil icon)
5.2. Locate the drop-down menu called preset and
channel
5.3. Drop down and select CH1
5.4. Click on the input cropping slider to activate
cropping
5.5. Enter the desired values:
5.5.1. X1 = crop left side of image
5.5.2. Y1 = crop top of image
5.5.3. X2 = crop right side of image
5.5.4. Y2 = crop right side of image
Example:

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 11
Typical cropped sizes for a 1920 x 1080 starting aspect ratio, which is what the DAUs are set to output. This should be a
starting point and can be adjusted as required for each window/channel
1920
1080
X1
Y1
X2
Y2
Aspect
multiplier
240
0
1680
1080
4:3
1.33
0
0
1920
1080
16:9
1.777778
420
0
1500
1080
Square
1
285
0
1635
1080
1280x1024
1.25
DisplayPort inputs are directly connected to the back of the MSV2 and should output the exact aspect ratio of
the video source.
5.6. Click apply and note changes on the video screen. Adjust values as required.
5.7. Repeat for each channel CH2, CH3, & CH4
5.8. Verify keep aspect ratio is turned on for each channel as well
Rename Layouts and Channels
6. Renaming will occur in the Preset & Channel tab
6.1. Click on the preset & Channel tab
6.2. In the top click on the drop-down
menu and navigate to the
desired preset & channel.
6.3. Click in the Preset Name textbox
6.4. Type in the desired name.
6.5. Note: Use only letters and
numbers, symbols are not
allowed and will create errors
in the programming
6.6. Click apply
6.7. Rename each of the layouts as required, remember to click apply after renaming each of the layouts.
6.8. Channels can also be renamed in the same fashion.
6.9. Repeat steps 6.2 through 6.7, except select the desired channel in step 6.2
Saving and returning to guest mode
7. Go to the design tab
7.1. Hit the save button
7.2. Click on the sign out button at the top right of the page
7.3. Sign back into software using the following (case sensitive on both username and password)
7.3.1. Username: idi
7.3.2. Password: Password55

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 12
Monitor Menu Navigation
The following information is from FSN manual, FSN1995-7/2019, for additional monitor information please
reference FSN monitor manual.
Menu Access Points
•Lower Right Side
•Remote Control

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 13

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 14

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 15

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 16
General Cleaning
Tools: Soft cloth and approved cleaner:
oSodium hypochlorite (generic household bleach) in a solution of 5.25% sodium hypochlorite diluted between 1:10
and 1:100 with water.
oAlcohol (generic).
oEnvirocide. ™
Notes:
•For the cleaning of monitor or shelf equipment, please consult corresponding literature for these
devices.
•NEVER use alcohol to clean the monitor.
Procedure:
1.1. Unplug the ilex55 system prior to the cleaning process.
1.2. Wipe clean the surfaces of the system with a diluted mixture of mild detergent (listed above) and water, using a
soft cloth.
Use a soft cloth to dry any stainless steel items.
1.3. To clean speaker grilles, simply pull off and wash.
Large Monitor Cleaning FSN monitors only
Products FM-C5501DV, FM-A5502DC, FM-D5801DV, For Barco Tablet and Barco monitor see next section
Precautions
•Before cleaning, switch the display in stand-by position to prevent the control touch panel from being
activated inadvertently by sweeping over the front filter. In stand-by position the touch panel cannot be
activated by just sweeping over them. To switch the display on again, you must press the stand-by key
again.
•Take care not to damage or scratch the front filter or LCD panel.
•Be careful with rings or other jewelry that can touch the front filter
•Do not apply pressure on the front filter or LCD panel.
•Do not apply or spray liquid directly to the front filter, panel or cabinet as excess liquid may cause
damage to internal electronics. Instead, apply the liquid to the cleaning cloth.
•Follow your hospital protocol for the handling of blood and body fluids.
•The display is not disinfected or packed in sterile environment.
•Follow your hospital protocol in case the display needs to be disinfected prior to installation.
•Front Filter
•Proceed as follows:
o1. Remove dust with a dry, lint-free, non-abrasive soft cotton cloth.

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 17
o2. Remove fingerprints or grease using a lint-free, non-abrasive soft cotton cloth that is lightly
moistened with plain water or a mild commercial glass cleaning product suited for coated glass
surfaces.
o3. Gently wipe dry with a dry cloth.
•The following products are tested and approved:
•Misty Clear Lemon 10 Disinfectant
•Bohle glass cleaner
•Zep Heavy-duty glass & all surface cleaner
•Klear Screen
•Screen TFT (Kontakt Chemie)
•Incidin Foam (Ecolab)
•Microzid
•Mild detergent
•Isopropyl alcohol with concentration < 5%
•Household bleach (generic sodium hypochlorite, solutions of 5.25% sodium hypochlorite diluted with
water between 1:10 and 1:100)
DO NOT USE:
•Alcohol/solvents at higher concentration > 5%
•Strong alkalis lye
•Strong solvents
•Acid
•Detergents with fluoride
•Detergents with ammonia
•Detergents with abrasives
•Steel wool
•Sponge with abrasives
•Steel blades
•Cloth with steel thread
Cabinet
Proceed as follows:
1. Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for
medical equipment.
2. Repeat with water only.
3. Wipe dry with a dry cloth.
4. Cabinet has been tested for resistance to the following products:
•Virex Ready-to-use Disinfectant Cleaner
•Misty Clear Lemon 10 Disinfectant
•Bohle glass cleaner
•Zep Heavy-duty glass & all surface cleaner
•Klear Screen
•Screen TFT (Kontakt Chemie)
•Incidin Foam (Ecolab)
•Microzid
•Mild detergent

Installation Guide ilex55
L280-0974 REV A www.imagediagnostics.com Page 18
•Isopropyl alcohol with concentration < 5%
•Household bleach (generic sodium hypochlorite, solutions of 5.25% sodium hypochlorite diluted with
water between 1:10 and 1:100)
•Precise Hospital Foam Cleaner Disinfect
Large Monitor Cleaning Barco Only
Cleaning Instructions
•Be sure to unplug the power cord from the mains when cleaning your LCD monitor.
•Take care not to scratch the front surface with any hard or abrasive material.
•Dust, finger marks, grease etc. can be removed with a soft damp cloth (a small amount of mild detergent
can be used on the damp cloth).
•Wipe off water drop immediately.
Possible cleaning solutions
•250 ppm chlorine solution
•NaCI solution 0.9% –Sodim chloride 00-236
•Bacillol AF
•1.6 percent aqueous ammonia
•Cidex® (2.4 percent glutaraldehyde solution)
•Sodium hypochlorite (bleach) 10 percent
•“Green soap” (USP)
•Like Cleansafe® optical cleaning liquid
•Isopropanol
•Haemosol solution (1% in 1 liter water)
•Chlorehexidine 0,5% in 70% Ethanol
Barco Tablet cleaning
WARNING: Unplug the power cable from the mains power input before cleaning the display.
CAUTION: Take care not to damage or scratch the front glass or LCD. Be careful with rings or other jewelry
and do NOT apply excessive pressure on the front glass or LCD.
CAUTION: Do NOT apply or spray liquid directly to the display as excess liquid may cause damage to
internal electronics. Instead, apply the liquid to a cleaning cloth.
To clean the display
Clean the display using a sponge, cleaning cloth or soft tissue, lightly moistened with a recognized cleaning
product for medical equipment. Read and follow all label instructions on the cleaning product. In case of doubt
about a certain cleaning product, use plain water.
Possible cleaning solutions:
• 70% isopropyl alcohol
• 1.6% aqueous ammonia
• Cidex® (2.4% glutaraldehyde solution)
• Sodium hypochlorite (bleach) 10%
• “Green soap” (USP)
• 0.5% Chlorehexidine in 70% isopropyl alcohol
• Like Cleansafe® optical cleaning liquid
Do not use following products:
• Alcohol/solvents at higher concentration > 70%