IEI Technology SPCIE-C2260 User manual

1
Full-size PICMG 1.3 CPU card supports LGA1150 Intel® Xeon® E3/
Core™ i3/Pentium® and Celeron® per Intel® C226, DDR3,
VGA, IDP, Dual Intel® PCIe GbE, SATA 6Gb/s, mSATA,
mini PCIe, RS-232, HD Audio, iRIS-2400 and RoHS
SPCIE-C2260-i2
Quick Installation Guide
Version 1.0
Nov. 13, 2015.
Package List
SPCIE-C2260-i2 package includes the following items:
1 x SPCIE-C2260-i2 single board computer
1 x Dual RS-232 cable
2 x SATA cable
1 x USB cable
1 x Utility CD
1 x QIG (Quick Installation Guide)
©2006 Copyright by IEI Integration corp.
All rights reserved.

2
Specifications
CPU:
LGA1150 Intel® Xeon® E3/Core™ i3/Pentium® or Celeron®
processor supported
PCH: Intel® C226
Memory:
Four 240-pin 1600/1333MHz dual-channel DDR3 & DDR3L
SDRAM ECC and non-ECC unbuffered DIMMs support up to
32GB
BIOS: UEFI BIOS
Graphic Engine:
Intel® HD Graphics Gen 7.5 support for DX11.1 and OpenCL
1.2, OpenGL 3.2 Full MPEG2, VC1, AVC Decode
Display Output:
VGA (Up to 1920x1200 @ 60 Hz)
iDP interface for HDMI, LVDS,VGA, DVI, DP
(Up to 3840x2160 @60 Hz)
Ethernet:
LAN1: Intel® I217LM Clarkville-V with Intel® iAMT 9.0 support
LAN2: Intel® I210 PCIe controller
Super IO: Fintek F81866
EC: IWDD
Digital I/O: 8-bit digital I/O (4-bit input / 4-bit output)
Audio: Supports by IEI AC-KIT-892HD audio kit
I/O Interface:
4 x RS-232
1 x RS-422/485
1 x LPT
1 x 6-pin wafer for KB/MS
1 x mSATA (colay SATA port 6)
6 x SATA 6GB/s (RAID 0, 1, 5, 10 supported)
8 x USB 2.0 (4 by pin header, 4 by backplane pin header)

3
4 x USB 3.0 (2 on rear IO, 4 by pin header)
Watchdog Timer:
Software programmable support 1~255 sec. system reset
FAN:
1 x 4-pin CPU fan connector
1 x 3-pin system fan connector
Front Panel:
1 x Front Panel
(Power LED, HDD LED, Speaker, Power Button, Reset Button)
LAN LED: 2 x 2 Pin for LAN1 LED, LAN2 LED (Active)
TPM: 1 x 20-pin (2x10) header
SMBus: 1 x 4-pin (1x4) wafer
I2C: 1 x 4-pin (1x4) wafer
IR: 1 x 5-pin (1x5) header
IPMI: 1 x DDR3 SO-DIMM slot supports iRIS-2400
Expansion:
PCIe signal and PCI signal via golden finger
PCI signal by ITE 8892 (PCIe to PCI bridge)
1 x mini PCIe slot supports PCIe x 1, USB devices and mSATA
Power supply:
5V/12V, AT/ATX support
Power Consumption:
[email protected], [email protected]7A, [email protected]A, [email protected],
[email protected]A
(3.4GHz Intel® CPU with four GB 1333MHz DDR3 memory)
Operation Temperature: -20°C ~ 60°C
Operation Humidity: 5% ~ 95%, non-condensing
Dimensions: 338mm x 126mm
Weight GW/NW: 1200g / 420g

4
Ordering Information
SPCIE-C2260-i2-R10:
Full-size PICMG 1.3 CPU card supports LGA1150 Intel® Xeon®
E3/Core™ i3/Pentium® and Celeron per Intel® C226, DDR3,
VGA, IDP, Dual Intel® PCIe GbE, SATA 6Gb/s, mSATA, RS-232,
mini PCIe, HD Audio, iRIS-2400 and RoHS
32200-074800-RS: RS-422/485 cable, 200mm
19800-010500-100-RS: USB 3.0 cable with bracket
19800-000075-RS: KB/MS cable with bracket
SAIDE-KIT01-R10: SATA to IDE/CF converter board
32102-000100-200-RS:
SATA power cable, MOLEX 5264-4P to SATA15P
19800-000049-RS: LPT Cable
AC-KIT-892HD-R10:
7.1 channel HD Audio kit with Realtek ALC892 support dual
audio streams
CF-1150SA-R10: Special cooler kit for LGA1150, High-performance
compatible, 95W
CF-1150SB-R10: Special cooler kit for LGA1150, High-performance
compatible, 65W
CF-1150SC-R10:
Special cooler kit for LGA1150, 1U chassis compatible, 65W
DP-DVI-R10:
DisplayPort to DVI-D converter board (For iEi IDP connector)
DP-HDMI-R10:
DisplayPort to HDMI converter board (For iEi IDP connector)
DP-LVDS-R10:
DisplayPort to LVDS converter board (For iEi IDP connector)
DP-VGA-R10:
DisplayPort to VGA converter board (For iEi IDP connector)
DP-DP-R10:
DisplayPort to DisplayPort converter board (For iEi IDP connector)

5
Jumpers setting and connectors
LABEL FUNCTION
J_ATX_AT1 AT/ATX mode select switch
J_CMOS1 Clear CMOS button
PCIE x16 Power PCIEX16 channel mode setting
USB SW1, USB SW2 USB power setting
MSATA_SW1 M-SATA switch auto-detect
J_FLASH1 Flash descriptor security override
J_AUDIO1 Audio source connector
BAT1 Battery connector
CHASSIS1 Chassis status connector
CPU_FAN1 CPU fan connector
CPU12V1 +12V power connector
CHA_DIMM1, CHA_DIMM2
CHB_DIMM1, CHB_DIMM2
DDR3 DIMM slots
DIO1 Digital I/O connector
DP1 Display port connector
CN3 EC debug connector
F_PANEL1 Front panel connector
IPMI1 Collocation IPMI module (iRIS-2400)
IR1 IrDA Infrared Interface Connector
CN1 I2C Connector
KB_MS1 Keyboard and mouse connector
LED_LAN1 LAN1 link LED connector
LED_LAN2 LAN2 link LED connector
LPT1 Parallel port connector
CN4 M-SATA card connector
COM1, COM3, COM4, COM5 RS-232 serial port connector
COM2 RS-422/485 serial port connector
SATA1, SATA2, SATA3
SATA4, SATA5, SATA6 SATA 6Gb/s drive connectors
CN2 SMBUS connector
SPDIF1 SPDIF connector
JSPI1 Flash SPI ROM connector

6
JSPI2 Flash EC ROM connector
SYS_FAN1 System fan connector
TPM1 TPM connector
USB1, USB2 Internal USB 2.0 connectors
CN7 Internal USB 3.0 connector
LAN1, LAN2 RJ45 LAN connectors
CN5, CN6 External USB 3.0 ports
VIDEO1 VGA connector
J_CMOS1: Clear CMOS button
PIN NO. DESCRIPTION
NC (default)
Keep CMOS Setup
(Normal Operation)
Press button Clear CMOS Setup
J_ATX_AT1: AT/ATX mode select switch
PIN NO. DESCRIPTION
Short 1 - 2 ATX Mode (default)
Short 2 - 3 AT Mode

7
USB SW1, USB SW2: USB power setting
PCIE x16 DESCRIPTION
+5V DUAL 5V DUAL (default)
+5V +5V
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Chipset
Auto Power Button Status [Disabled(ATX)]
Restore AC Power Loss [Last State]
> PCI Express Configuration
> PCI Azalia Configuration
Power Saving Function(ERP) [Disabled]
PCIEX16 Power [1 x16 PCIE]
USB SW1 [+5V DUAL]
USB SW2 [+5V DUAL]
------------------
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
PCIE x16 Power: PCIEX16 channel mode setting
PCIE x16 DESCRIPTION
1 x16 PCIE 1 x16 PCIE (default)
2 x8 PCIE 2 x8 PCIE
1 x8 , 2x4 PCIE 1 x8 , 2x4 PCIE
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Chipset
Auto Power Button Status [Disabled(ATX)]
Restore AC Power Loss [Last State]
> PCI Express Configuration
> PCI Azalia Configuration
Power Saving Function(ERP) [Disabled]
PCIEX16 Power [1 x16 PCIE]
USB SW1 [+5V DUAL]
USB SW2 [+5V DUAL]
------------------
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.

8
CHASSIS1: Chassis status connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3VSB 2 CHASSIS OPEN
J_AUDIO1: Audio source connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
HDA_SYNC
2
HDA_BIT_CLK
3
HDA_SDOUT
4
HDA_SPKR
5
HDA_SDIN
6
HDA_RST#
7
HDA_VCC
8
HDA_GND
9
HDA_+12V
10
HDA_GND
BAT1: Battery connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VBATT 2 GND
J_FLASH1: Flash descriptor security override
PIN NO. DESCRIPTION
Short 1 - 2 Disabled (default)
Short 2 - 3 Enabled
MSATA_SW1: M-SATA switch auto-detect
PIN NO. DESCRIPTION
Open Auto Detect M-SATA (default)
Short M-SATA Enable
CPU_FAN1: CPU fan connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
+12V
3
FANIO
4
PWM

9
DP1: Display port connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
+5V
2
LANE1N
3
LANE1P
4
GND
5
LANE3N
6
LANE3P
7
GND
8
AUX_CTRL_DET_D
9
GND
10
HPD
11
AUXP
12
AUXN
13
GND
14
LANE2P
15
LANE2N
16
GND
17
LANE0P
18
LANE0N
19
+3.3V
20
NC
CPU12V1: +12V power connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
GND
3
+12V
4
+12V
DIO1: Digital I/O connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
VCC
3
Output 3
4
Output 2
5
Output 1
6
Output 0
7
Input 3
8
Input 2
9
Input 1
10
Input 0

10
IR1: IrDA connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +V5S 2 NC
3 IR-RX 4 IR-RX
5 IR-TX
F_PANEL1: Front panel connector
PIN DESCRIPTION PIN DESCRIPTION
PWR
LED
1
+5V
2
BEEP_PWR SPKR
3
NC
4
IPMI ID_LED+
IPMI LED
5
GND
6
IPMI ID_LED-
PWR
BTN
7
PWRBTN_SW#
8
PC_BEEP SPKR
9
GND
10
NC
RESET
HDD
LED
11
+5V
12
EXTRST-
13
SATA_LED#
14
GND
CN3: EC debug connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
EC_EPP_STB#
2
EC_EPP_AFD#
3
EC_EPP_PD0
4
NC
5
EC_EPP_PD1
6
EC_EPP_INIT#
7
EC_EPP_PD2
8
EC_EPP_SLIN#
9
EC_EPP_PD3
10
GN
D
11
EC_EPP_PD4
12
NC
13
EC_EPP_PD5
14
EC_EPP_BUSY
15
EC_EPP_PD6
16
EC_EPP_
KSI5
17
EC_EPP_PD7
18
EC_EPP_
KSI4

11
LED_LAN2: LAN2 link LED connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 2 LAN2_LED_LNK#_ACT
LED_LAN1: LAN1 link LED connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 2 LAN1_LED_LNK#_ACT
CN1: I2C Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 PCH_GP38
(I2C_DAT)
3 PCH_GP39
(I2C_CLK) 4 +5V
KB_MS1: Keyboard and mouse connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 MSDATA
3 MSCLK 4 KBDATA
5 KBCLK 6 GND

12
LPT1: Parallel port connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
STROBE#
2
DATA0
3
DATA1
4
DATA2
5
DATA3
6
DATA4
7
DATA5
8
DATA6
9
DATA7
10
ACKNOWLEDGE
#
11
BUSY
12
PAPER EMPTY
13
PRINTER SELECT
14
AUTO FORM FEED #
15
ERROR#
16
INITIALIZE
#
17
PRINTER SELECT LN#
18
GND
19
GND
20
GND
21
GND
22
GND
23
GND
24
GND
25
GND
26
NC

13
CN4: M-SATA card connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
PCIE_WAKE#
2
+3.
3
V
3
N/C
4
GND
5
N/C
6
1.5V
7
N/C
8
N/C
9
GND
10
N/C
11
MSATA_CLK#
12
N/C
13
MSATA _CLK
14
N/C
15
GND
16
N/C
17
PLTRS
T_N
18
GND
19
N/C
20
+3.
3
V
21
GND
22
PLTRST_N
23
SATA_RX+
24
+3.
3
V
25
SATA_RX
-
26
GND
27
GND
28
1.5V
29
GND
30
SMB
_
CLK
31
SATA_TX
-
32
SMB
_
DATA
33
SATA_TX+
34
GND
35
GND
36
USB
_
D
ATA
-
37
GND
38
USB
_
D
ATA
+
39
+3.
3
V
40
GND
41
+3.
3
V
42
N/C
43
+3.
3
V
44
N/C
45
C
LINK
_CLK
46
N/C
47
CL
INK
_DATA
48
1.5V
49
CL
INK
_RST#
50
GND
51
MSATA_DET
52
+3.
3
V

14
CN2: SMBUS connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
SMB_DATA
3
SMB_CLK
4
+5V
SATA1
,
SATA
2,
SATA
3,
SATA
4,
SATA
5,
SATA
6
:
SATA
6
Gb/s drive
connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1GND 2 SATA_TX+
3SATA_TX- 4 GND
5 SATA_RX- 6 SATA RX+
7 GND
COM2: RS-422/485 serial port connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1RXD485# 2 RXD485+
3TXD485+ 4 TXD485#
COM1, COM3, COM4, COM5: RS-232 serial port connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RST
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
GN
D

15
SYS_FAN1: System fan connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
FANIO
2
+12V (PWM)
3
GND
JSPI2: Flash EC ROM connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
+3.3V
2
SPI_CS#
3
SPI_SO
4
NC
5
GND
6
SPI_CLK
7
SPI_SI
8
NC
JSPI1: Flash SPI ROM connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
+3.3V
2
SPI_CS#
3
SPI_SO
4
NC
5
GND
6
SPI_CLK
7
SPI_SI
8
NC
SPDIF1: SPDIF connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
+5V
2
NC
3
SPDIF
OUT
4
GN
D
5
SPDIF
IN

16
CN7: Internal USB 3.0 connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 USB3_RX-
3 USB3_RX+ 4 GND
5 USB3_TX- 6 USB3_TX+
7 GND 8 USB_DATA-
9 USB_DATA+ 10 NC
11 USB_DATA+ 12 USB_DATA-
13 GND 14 USB3_TX+
15 USB3_TX- 16 GND
17 USB3_RX+ 18 USB3_RX-
19 VCC 20 NC
USB1, USB2: Internal USB 2.0 connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 GND
3 USB_DATA- 4 USB_DATA+
5 USB_DATA+ 6 USB_DATA-
7 GND 8 VCC
TPM1: TPM connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
LCLK
2
GND
3
LFRAME#
4
NC
5
LRERST#
6
+5V
7
LAD3
8
LAD2
9
+3.3V
10
LAD1
11
LAD0
12
GND
13
SCL
14
SDA
15
SB3V
16
SERIRQ
17
GND
18
GLKRUN#
19
LPCPD#
20
LDRQ#

17
LAN1, LAN2: RJ45 LAN connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
MDIA3
-
2
MDIA3+
3
MDIA2
-
4
MDIA
2+
5
MDIA1
-
6
MDIA
1
+
7
MDIA0
-
8
MDIA0+
VIDEO1: VGA connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RED 2 GREEN
3 BLUE 4 NC
5 GND 6 GND
7 GND 8 GND
9 VCC 10 GND
11 NC 12 DDCDA
13 HSYNC 14 VSYNC
15 DDCCLK
CN5, CN6: External USB 3.0 ports
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
VBUS
2
D-
3
D+
4
GND
5
STDA_SSRX_N
6
STDA_SSRX_P
7
GND_DRAIN
8
STDA_SSTX_N
9
STDA_SSTX_P

18
Board Layout: Jumper and Connector Locations
(Unit: mm)