IEI Technology TANGO-3010 Series User manual

User Manual
Embedded System with Intel® Celeron™ J6412 Processor,
LPDDR4X, Two HDMI 1.4b, Three 2.5 GbE LAN, RS-232/422/485, USB 3.2
RoHS Compliant
TANGO-3010 Series
MODEL:
Rev. 1.00 –November 29, 2022

Page II
TANGO-3010 Embedded System
Revisions
Date
Version
Changes
November 29, 2022
1.00
Initial release

Page III
TANGO-3010 Embedded System
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

Page IV
TANGO-3010 Embedded System
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.
HOT SURFACE
This symbol indicates a hot surface that should not be touched without
taking care.

Page V
TANGO-3010 Embedded System
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 FEATURES................................................................................................................... 3
1.3 FRONT PANEL............................................................................................................. 3
1.4 REAR PANEL............................................................................................................... 4
1.5 LEFT SIDE PANEL ....................................................................................................... 4
1.6 TECHNICAL SPECIFICATIONS ...................................................................................... 5
1.7 PHYSICAL DIMENSIONS.............................................................................................. 8
2 UNPACKING................................................................................................................. 9
2.1ANTI-STATIC PRECAUTIONS...................................................................................... 10
2.2 UNPACKING PRECAUTIONS....................................................................................... 10
2.3 UNPACKING CHECKLIST............................................................................................11
3 INSTALLATION ......................................................................................................... 13
3.1 INSTALLATION PRECAUTIONS................................................................................... 14
3.2 BACK COVER REMOVAL........................................................................................... 15
3.3 STORAGE INSTALLATION .......................................................................................... 15
3.3.1 Tool-Less HDD/SSD Installation..................................................................... 16
3.3.2 HDD/SSD Removal.......................................................................................... 17
3.3.3 M.2 SSD Installation........................................................................................ 18
3.4 BACK COVER INSTALLATION.................................................................................... 19
3.5 EXTERNAL PERIPHERAL INTERFACE CONNECTORS................................................... 20
3.5.1 HDMI Connection............................................................................................ 20
3.5.2 USB Device Connection................................................................................... 20
3.5.3 LAN Connection............................................................................................... 21
3.5.4 RS-232/422/485 Serial Port Connection ......................................................... 22
3.6 POWERING ON/OFF THE SYSTEM ............................................................................. 23
3.7 POWER INPUT........................................................................................................... 23
3.8AVAILABLE DRIVERS ................................................................................................ 24

Page VI
TANGO-3010 Embedded System
3.8.1 Driver Download............................................................................................. 24
4 SYSTEM MOTHERBOARD ..................................................................................... 26
4.1 OVERVIEW................................................................................................................ 27
4.1.1 Layout .............................................................................................................. 27
4.2 INTERNAL PERIPHERAL CONNECTORS...................................................................... 29
4.2.1 Battery Connector (BAT2) ............................................................................... 29
4.2.2 CPU Fan Connector (CPU_FAN1).................................................................. 29
4.2.3 System Debug Connector (DBG_PORT1)....................................................... 30
4.2.4 EC Debug Connector (EC_DEBUG1)............................................................. 30
4.2.5 EC Flash Connector (EC_FLASH1)................................................................ 30
4.2.6 Power Button Connector (PWR_BTN2) .......................................................... 30
4.2.7 SATA Connector (SATA0)................................................................................. 31
4.2.8 AT/ATX Power Mode Switch (J_ATX_AT1)..................................................... 31
4.2.9 BIOS Programming Connector (JBIOS1) ....................................................... 31
4.2.10 Clear CMOS Button (J_CMOS1)................................................................... 32
4.2.11 Flash Override Jumper (J_FLASH1)............................................................. 32
4.3 EXTERNAL INTERFACE PANEL CONNECTORS ............................................................ 33
4.3.1 External HDMI 1.4 Combo Connectors (HDMI1, HDMI2)............................ 33
4.3.2 External 2.5GbE LAN Connectors (LAN1, LAN2, LAN3)............................... 34
4.3.3 External RS-232/422/485 Serial Port Connector (COM1).............................. 35
4.3.4 External RS-232 Serial Port Connector (COM2)............................................ 35
4.3.5 External USB 3.2 Gen 2 Connectors (USB1, USB2)....................................... 36
4.3.6 External USB 2.0 Type-A Connectors (USB3, USB4)...................................... 36
A REGULATORY COMPLIANCE.............................................................................. 37
B SAFETY PRECAUTIONS......................................................................................... 44
B.1 SAFETY PRECAUTIONS............................................................................................. 45
B.1.1 General Safety Precautions............................................................................. 45
B.1.2 Anti-static Precautions .................................................................................... 46
B.1.3 Product Disposal ............................................................................................. 47
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 47
B.2.1 Maintenance and Cleaning.............................................................................. 48
B.2.2 Cleaning Tools................................................................................................. 48
C ERROR BEEPCODE ................................................................................................ 49

Page VII
TANGO-3010 Embedded System
C.1 PEI BEEP CODES ..................................................................................................... 50
C.2 DXE BEEP CODES ................................................................................................... 50
D HAZARDOUS MATERIALS DISCLOSURE......................................................... 51
D.1 ROHS II DIRECTIVE (2015/863/EU) ....................................................................... 52
D.2 CHINA ROHS........................................................................................................... 53

Page VIII
TANGO-3010 Embedded System
List of Figures
Figure 1-1: TANGO-3010 Series-J6412.........................................................................................2
Figure 1-2: Front Panel ..................................................................................................................3
Figure 1-3: Rear Panel....................................................................................................................4
Figure 1-4: Physical Dimensions ..................................................................................................8
Figure 3-5: Remove the Cover.....................................................................................................15
Figure 3-6: Connect the HDD/SSD and Align with the Bracket................................................16
Figure 3-7: Seat the HDD/SSD to the Bracket............................................................................17
Figure 3-8: Remove the HDD/SSD...............................................................................................17
Figure 3-9: Removing the M.2 Module Retention Screw ..........................................................18
Figure 3-10: Inserting the M.2 Module into the Slot at an Angle .............................................18
Figure 3-11: Securing the M.2 Module........................................................................................19
Figure 3-12: Back Cover Installation ..........................................................................................19
Figure 3-13: HDMI Connection ....................................................................................................20
Figure 3-14: USB Connection......................................................................................................20
Figure 3-15: LAN Connection......................................................................................................21
Figure 3-16: DB-9 Serial Port Connector....................................................................................22
Figure 3-17: Serial Device Connection.......................................................................................22
Figure 3-18: Power Button...........................................................................................................23
Figure 3-19: Power Connector ....................................................................................................23
Figure 3-20: IEI Resource Download Center..............................................................................24
Figure 4-21: System Motherboard (Solder Side).......................................................................27
Figure 4-22: System Motherboard ..............................................................................................28
Figure 4-23: HDMI Connector......................................................................................................34
Figure 4-24: LAN Connectors......................................................................................................34
Figure 4-25: RS-232/422/485 Serial Port Connectors................................................................35
Figure 4-26: USB 3.2 Gen 2 Port Location .................................................................................36

Page IX
TANGO-3010 Embedded System
List of Tables
Table 1-1: Technical Specifications..............................................................................................7
Table 1-2:WLAN/Bluetooth Frequency range and power...............................错误!未定义书签。
Table 3-1: RJ-45 Ethernet Connector LEDs...............................................................................21
Table 3-2: RS-232 (COM1) & RS-232/422/485 (COM2) Connector Pinouts..............................22
Table 4-1: Peripheral Interface Connectors...............................................................................29
Table 4-2: Battery Connector Pinouts........................................................................................29
Table 4-3: CPU Fan Connector Pinouts .....................................................................................29
Table 4-4: System Debug Connector Pinouts ...........................................................................30
Table 4-5: EC Debug Connector Pinouts ...................................................................................30
Table 4-6: EC Flash Connector Pinouts.....................................................................................30
Table 4-7: Power Button Connector Pinouts.............................................................................30
Table 4-8: SATA Connector Pinouts...........................................................................................31
Table 4-9: AT/ATX Power Mode Switch Pinouts........................................................................31
Table 4-10: BIOS Programming Connector Pinouts .................................................................31
Table 4-11: Clear CMOS Button Pinouts....................................................................................32
Table 4-12: Flash Descriptor Security Override Jumper Pinouts............................................32
Table 4-13: Rear Panel Connectors ............................................................................................33
Table 4-14: HDMI Connector Pinouts .........................................................................................33
Table 4-15: LAN Connectors Pinouts.........................................................................................34
Table 4-16: LAN Connectors LEDs .............................................................................................34
Table 4-17: RS-232/422/485 Serial Port Connector Pinouts.....................................................35
Table 4-18: RS-232 Serial Port Connector Pinouts ...................................................................35
Table 4-19: USB 3.2 Gen 2 Connectors Pinouts........................................................................36
Table 4-20: USB 2.0 Type-A Connectors Pinouts......................................................................36

Page 1
TANGO-3010 Embedded System
Chapter
1
1Introduction

Page 2
`
TANGO-3010 Embedded System
1.1 Overview
Figure 1-1: TANGO-3010 Series-J6412
The TANGO-3010 Series is an embedded system with Intel® Celeron®J6412 processor
and 8GB LPDDR4X on-board memory. It is equipped with three 2.5 GbE LAN ports, two
USB 3.2 Gen 2 (10Gb/s) ports, two USB 2.0 ports, one RS-232 (3T5R) port and one
RS-232/422/485 port.
The TANGO-3010 Series has two HDMI 1.4b ports supporting up to 4k@ 30Hz resolution,
and includes one M.2 2230 A-key slot and one M.2 2280 M-key slot for expansions.

Page 3
TANGO-3010 Embedded System
1.2 Features
The TANGO-3010 Series features are listed below:
Intel® Celeron®J6412 2.0 GHz processor (up to 2.6 GHz, quad-core, TDP
10W) and 8GB LPDDR4X on-board memory
Dual independent displays with high resolution support
Rich high-speed I/O interfaces
One 2.5" HDD/SSD SATA 6Gb/s bay (supports up to 9.5 mm SSD)
One M.2 A-key and M.2 M-key expansion
1.3 Front Panel
The front panel of the TANGO-3010 Series has the following features (See Figure 1-2):
Figure 1-2: Front Panel

Page 4
`
TANGO-3010 Embedded System
1.4 Rear Panel
The rear panel of the TANGO-3010 Series is shown below (See Figure 1-3).
Figure 1-3: Rear Panel
1.5 Left Side Panel
The left side panel of the TANGO-3010 Series is shown below (See Figure 1-3).
Figure 1-4: Left Side Panel

Page 5
TANGO-3010 Embedded System
1.6 Technical Specifications
The TANGO-3010 Series technical specifications are listed in Table 1-1, Table 1-2
Specifications
Chassis
Color
Black C & grey (Pantone 430C)
Dimensions (WxDxH) (mm)
139 x 137 x 39.8
System Fan
Fanless
Chassis Construction
ABS Plastic + Aluminum
Motherboard
CPU
Intel® Celeron®J6412 2GHz (up to 2.6GHz, TDP 10W)
Chipset
SoC
System Memory
LPDDR4X on board 8GB (up to 16G)
Storage
Hard Drive
1 x 2.5" HDD/SSD SATA6Gb/s bay (supports up to 9.5 mm SSD)
I/O Interfaces
Ethernet
3 x RJ-45 2.5 GbE by I225V controller
USB
2 2 x USB 3.2 Gen 2 (10Gb/s)
3 2 x USB 2.0
Display
2 x HDMI 1.4b with CEC support (up to 4K @ 30Hz)
COM
1 x RS-232 (DB9)
1 x RS-232/422/485 (DB9)
Wireless
INTEL AX210 WiFi 6E & Bluetooth 5.2 Module built-in 2T2R
antenna

Page 6
`
TANGO-3010 Embedded System
TPM 2.0
Intel® PTT
Expansions
M.2
1 x 2230 A-key (PCIe 1/USB2.0)(preinstalled WIFI Module)
1 x 2280 M-key (PCIe 4)
Power
Power Input
DC jack: 12 V DC
Power Consumption
[email protected] (Intel® Celeron J6412 with 8GB memory)
Reliability
Mounting
60.6 x 11.55 With conversion vesa75/100 bracket
Operating Temperature
0 ~ 40°C with air flow (SSD)
Operating Humidity
10% ~ 95%, non-condensing
Storage Temperature
-10°C ~ 60°C with air flow (SSD)
Storage Humidity
10% ~ 90%, non-condensing
Operating Shock
Half-sine wave shock 5G, 11ms, 100 shocks per axis (SSD)
Operating Vibration
MIL-STD-810G 514.6C-1 (with SSD)
Weight (Net/Gross)
0.57/1.35kg
Safety/EMC
CE/RED/FCC
Watchdog Timer
Programmable 1~255 sec/min
Others
Switch
1 x Power Button (with LED)
1 x Reset Button

Page 7
TANGO-3010 Embedded System
OS
Supported OS
Microsoft® Windows® 10 / Windows® 11
Linux
Table 1-1: Technical Specifications
Technology
Frequency range/MHz
Max.E.I.R.P/dBm
WLAN 2.4GHz
2400-2483.5
20
WLAN 5GHz
5150-5250
23
WLAN 5GHz
5250-5350
23
WLAN 5GHz
5470-5725
23
WLAN 5GHz
5725-5850
13.98
WLAN 6GHz
5945-6425
14
Bluetooth BR/EDR
2402-2480
20
Bluetooth LE
2402-2480
20
Table 1-2:WLAN/Bluetooth Frequency range and power

Page 8
`
TANGO-3010 Embedded System
3.1 Physical Dimensions
The physical dimensions of the TANGO-3010 are shown in Figure 1-4.
Figure 1-4: Physical Dimensions

Page 9
TANGO-3010 Embedded System
Chapter
2
4Unpacking

Page 10
`
TANGO-3010 Embedded System
4.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during installation may result in
permanent damage to the TANGO-3010 Series and severe injury to
the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the TANGO-3010 Series. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the TANGO-3010 Series or any other electrical component
is handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the TANGO-3010 Series, place it
on an antic-static pad. This reduces the possibility of ESD damaging the
TANGO-3010 Series.
4.2 Unpacking Precautions
When the TANGO-3010 Series is unpacked, please do the following:
Follow the anti-static precautions outlined in Section 4.1.
Make sure the packing box is facing upwards so the TANGO-3010 Series
does not fall out of the box.
Make sure all the components shown in Section 4.2 are present.

Page 11
TANGO-3010 Embedded System
4.3 Unpacking Checklist
NOTE:
If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the TANGO-3010 Series from or contact an IEI
sales representative directly. To contact an IEI sales representative,
please send an email to [e-mail].
The TANGO-3010 Series is shipped with the following components:
Quantity
Item and Part Number
Image
Standard
1
TANGO-3010 Series
1
VESA mounting kit
1
Mounting screw pack
1
Power cord