Impex MARCY IVT-450 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
IVT-50
Retain This
Manual for
Reference
05-27-09
OWNER'S
MANUAL
MARCY®CLASSIC
INVERSION TABLE
IVT-450
IMPEX®INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................…. 1
IMPORTANT SAFETY NOTICES..................................................................…. 2
HARDWARE IDENTIFIER.....…....................................................................…. 4
ASSEMBLY INSTRUCTIONS........................................................................…. 5
EXPLODED DIAGRAM………………………………………………………………. 11
PARTS LIST...............................................................................................……. 12
WARRANTY.................................................................................................…. 13
ORDERING PARTS.......................................................................................… 13
BEFORE YOU BEGIN
Thank you for selecting the MARCY CLASSIC IVT-450 Inversion Table by
IMPEX®INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call
our TOLL-FREE customer service number. Our Customer Service Agents
will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.
5. Keep hands and feet away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm
up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. This machine is designed and intended for home and consumer use only, not for
commercial use.
14. Make sure the Foot Lock securely locks both feet.
15. When doing inversion exercises, please hold onto the Handles with both hands.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS. 2

WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Rear Support Frame. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
3

HARDWARE IDENTIFIER
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4

ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine
to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Attach Front Support Frame (#1) to Rear Support Frame (#2). Secure them together
with one M10 x 1” Allen Bolt (#34), two Ø ¾” Washers (#45), and one M10 aircraft Nut
(#43) on each end.
C.)Attach a Ø ¾” Rubber Spacer (#24) to the lower hole on Rear Support Frame. Attach
one Short Horizontal Support to the Spacer. Align the holes. Secure the Short
Horizontal Support, Spacer, and Rear Support Frame together with one M8 x 2 5/8”
Allen Bolt (#37), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43). Repeat the
same procedure to install the Right Long Horizontal Support (#4) to Front Support
Frame.
D.)Connect the Short and Long Horizontal Support together with one M6 x ½” Allen Bolt
(#33), one Ø ½” Washer (#47), and one M6 Aircraft Nut (#44).
E.) Repeat Procedure C & D to install the other side.
F.) Press down the Short and Long Horizontal Support completely to stabilize the Front
and Rear Support Frame.
G.)Securely tighten all Nuts and Bolts installed.
5

DIAGRAM 1
6

STEP 2 (See Diagram 2)
A.) Attach the two Pivot Brackets (#12) to the Backrest Frame (#7) from each side.
B.) Secure each Pivot Bracket to the Backrest Frame with two M8 x ¾” Allen Bolts (#38)
and two Ø ¾” Washers (#45).
C.)Lift the Backrest Frame and insert the two Pivot Brackets into the open slot on Rear
Support Frame (#2). Make sure the groves on the Pivot are attached on the slots
completely and the Pivots can swing smoothly.
D.)Cover the two open slots on the Rear Support Frame with Left & Right Swivel Cover
(#30 & #31) to prevent finger trapped in the openings. DIAGRAM 2
7

STEP 3 (See Diagram 3)
A.) Attach the Left Handle (#8) to Front Support Frame (#1). Secure it with one M8 x ¾”
Allen Bolt (#35), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43).
B.) Attach the Left Handle to the Rear Support Frame (#2). Secure it with one M8 x 1 ¾”
Allen Bolt (#36), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43).
C.)Repeat Procedures A & B to install the Right Handle (#9).
DIAGRAM 3
8

STEP 4 (See Diagram 4)
A.) Pull up the Foot Adjustment Lock Pin (#23). Insert the Foot Lock Frame (#13) into the
Adjustment Fame (#11). Push down the Pin to securely lock the Foot Lock Frame in
position.
B.) Insert the Foot Support (#6) into the bottom of Adjustment Frame. Secure it with one M8 x
1 5/8” Allen Bolt (#40), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43).
C.)Insert the Foam Tube halfway through the hole on Adjustment Frame. Push two Foam
Rolls (#17) onto the Tube from both ends.
D.)Push two Curved Foam Rolls (#16) onto the tube on Foot Lock Frame from both ends.
DIAGRAM 4
9

STEP 5 (See Diagram 5)
A.) Pull out the Backrest Adjustment Lock Pin (#22). Insert the Adjustment
Frame (#11) into the opening on the vertical frame on the back of Backrest
Frame (#7). Push back the Pin into the selected hole on Adjustment
Frame.
B.) Insert the Ring Lock Pin (#21) through the hole on the vertical frame and
hole on Adjustment Frame to securely lock the Adjustment Frame.
C.)Attach hook on Inversion Adjustment Belt (#15) to Front Support Frame
(#1) and to the vertical frame on Backrest Frame. Adjust the length of the
Belt to adjust the extension of inversion.
D.)Attach one side of U-shaped Lock Pin (#14) on front of Adjustment Frame,
insert the other side into hole on Front Support Frame and secure with one
M8 Aircraft Nut to lock Inversion Table for usage.
E.) When using the Inversion Table, remove the side of U-shaped Lock Pin off
from Adjustment Frame. DIAGRAM 5
10

EXPLODED DIAGRAM
11

PARTS LIST
KEY NO. DESCRIPTION QUANTITY
1 Front Support Frame 1
2 Rear Support Frame 1
3 Short Horizontal Support 2
4 Right Long Horizontal Support 1
5 Left Long Horizontal Support 1
6 Foot Support 1
7 Backrest Frame 1
8 Left Handle 1
9 Right Handle 1
10 Foam Tube 1
11 Adjustment Frame 1
12 Pivot Bracket 2
13 Foot Lock Frame 1
14 U-shaped Lock Pin 1
15 Inversion Adjustment Belt 1
16 Curved Foam Roll 2
17 Foam Roll 2
18 Hook 2
19 Backrest 1
20 Ø 1 ¼” End Cap 4
21 Ring Lock Pin 1
22 Backrest Adjustment Lock Pin 1
23 Foot Adjustment Lock Pin 1
24 Ø ¾” Rubber Spacer 4
25 Rubber Bumper 1
26 Handle Grip 2
27 Foam Roll End Cap 4
28 ¾” x 2 3/8” End Cap 2
29 1” Square End Cap 1
30 Left Swivel Cover 1
31 Right Swivel Cover 1
32 Ø 1 ¼” End Cap 2
33 M6 x ½” Allen Bolt 2
34 M10 x 1” Allen Bolt 2
35 M8 x ¾” Allen Bolt 2
36 M8 x 1 ¾” Allen Bolt 2
37 M8 x 2 5/8” Allen Bolt 4
38 M8 x ¾” Allen Bolt 4
39 M6 x 1 5/8” Allen Bolt 1
40 M8 x 1 5/8” Allen Bolt 1
41 M6 x 5/8” Philips Screw 1
42 M10 Aircraft Nut 2
43 M8 Aircraft Nut 10
44 M6 Aircraft Nut 3
45 Ø ¾” Washer 8
46 Ø 5/8” Washer 9
47 Ø ½” Washer 3
12

IMPEX®INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase.
This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited
to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights for products return to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused
by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided
by an IMPEX authorized service center or for products used for commercial or rental purposes. No other
warranty beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic
loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation
or other consequential damages or whatsoever natures. Some states do not allow the exclusion or
limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to
state. Register on-line www.impex-fitness.com
IMPEX®INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-
8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
[e-mail]
When ordering replacement parts, always give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase
13