Impex IRON GRIP SPORT IGS-08 User manual

NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
IGS-08
Retain This
Manual for
Reference
02-08-02
OWNER'S
MANUAL
IGS-08
NARROW BENCH
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE IDENTIFIER.....…....................................................................... 3
ASSEMBLY INSTRUCTIONS........................................................................... 4
EXPLODED DIAGRAM……………………………………………………………... 8
PARTS LIST……………………………………………………………………….. 9
WARRANTY.................................................................................................… 10
ORDERING PARTS......................................................................................... 10
BEFORE YOU BEGIN
Thank you for selecting the IRON GRIP SPORT IGS-08 Narrow Bench
by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this
manual carefully before using the machine. As a manufacturer, we are
committed to provide you complete customer satisfaction. If you have
any questions, or find there are missing or damaged parts, we guarantee
you complete satisfaction through direct assistance from our factory. To
avoid unnecessary delays, please call our TOLL-FREE customer
service number. Our Customer Service Agents will provide immediate
assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions
apply whenever you operate a piece of exercise equipment. Be sure to read the
entire manual before you assemble or operate your machine. In particular, note the
following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

3

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Adjustable Wrench and Allen
Wrench
NOTE: It is strongly recommended this machine to be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Rear Stabilizer (#11) to the bottom of the Upright Beam (#9). Secure it
with one Bracket (#15), four M10 x 2 ¾” Carriage Bolts (#12), ∅¾” Washers
(#13) and M10 Aircraft Nuts (#14). Repeat the same step for the other side.
B.) Place the Backrest Adjustment Bar (#7) on the selected bar holder on the Upright
Beam (#9) to obtain desired incline of Backrest.
C.) Insert two Crutches (#4) into the top openings on the Upright Beams (#9). Secure
them with two Lock Knobs (#6) through selected holes to obtain desired height of
the Crutches. Make sure both sides are at the same height. DIAGRAM 1
4

STEP 2 (See Diagram 2)
A.) Attach the rear of the Main Seat Support (#25) to the Upright Beam (#9). Secure
it with two M10 x 2 ¾” Allen Bolts (#16), four ∅¾” Washers (#13), and two M10
Aircraft Nuts (#14). Do not tighten the nuts and bolts yet.
B.) Slide the Sliding Block (#22) onto the Main Seat Support (#25). Secure it with a
Lock Knob (#6).
C.) Attach the Front Stabilizer (#40) to the Main Seat Support. Secure it with three
M10 x 2 ¾” Allen Bolts (#16), six ∅¾” Washers (#13), and three M10 Aircraft
Nuts (#14).
D.) Insert one Lock Knob (#6) into the hole on the back of Front Stabilizer (#40).
E.) Securely tighten all the nuts and bolts previously installed. DIAGRAM 2
5

STEP 3 (See Diagram 3)
A.) Attach two Seat Supports (#20), one on each side, to the pivot on the Sliding Block
(#22). Secure the Seat Supports (#20) to the two rear holes on the Seat Pad (#1)
using two M8 x 1 3/4” Allen Bolts (#18) and ∅½” Washers (#19).
B.) Attach the Seat Incline Adjustment (#27) to the two front holes on the Seat Pad.
Secure it with two M8 x 1” Allen Bolts (#26) and ∅1/2” Washers (#19). Place the
Seat Incline Adjustment onto the Sliding Block. Insert a L-shaped Pin (#28) into the
selected holes on the Seat Incline Adjustment to hold the desired incline.
C.)Attach two Backrest Supports (#17), one on each side, to the pivot on the Sliding
Block (#22). Place Backrest Board (#2) onto the Backrest Supports (#17). Secure it
with four M8 x 1 ¾” Allen Bolts (#18) and ∅½” Washers (#19).
DIAGRAM 3
6

STEP 4 (See Diagram 4)
A.) Insert the Leg Developer Holder (#41) into the opening on the Front Stabilizer (#40).
Secure it with the Lock Knob (#6).
B.) Attach the Leg Developer (#38) to the bracket on the Leg Developer Holder (#41). Secure
it with a M12 x 2 3/8” Axle (#36) and M12 Allen Bolt (#45).
C.) Secure the Leg Developer (#38) with a 4” Lock Pin (#36). Remove the Pin when using the
Leg Developer.
D.) Insert a Foam Roll Tube (#32) halfway through the hole on the Leg Developer Holder
(#41). Insert two Foam Roll Tubes (#32) halfway through the holes on the Leg Developer
(#38).
E.) Push six Foam Rolls (#33) onto the Tubes from both sides. Plug six Foam Roll End Caps
(#34) to the ends.
F.) Attach the Olympic Sleeve (#5) onto the weight post on the Leg Developer. Attach the
Spring Clip (#44) onto the Olympic Sleeve.
DIAGRAM 4
7

8

PARTS LIST
KEY NO. DESCRIPTION Q’ty
1 Seat Pad 1
2 Backrest Board 1
3 2” x 2 ¾” Sleeve 2
4 Crutch 2
5 Olympic Sleeve 1
6 Lock Knob 4
7 Backrest Adjustment Bar 1
8 1 ½” Square End Cap 2
9 Upright Beam 1
10 2” End Cap 6
11 Rear Stabilizer 2
12 M10 x 2 ¾” Carriage Bolt 8
13 ∅¾” Washer 18
14 M10 Aircraft Nut 13
15 Bracket 2
16 M10 x 2 ¾” Allen Bolt 3
17 Backrest Support 2
18 M8 x 1 ¾” Allen Bolt 6
19 ∅½” Washer 8
20 Seat Support 2
21 1” Square End Cap 4
22 Sliding Block 1
23 Sliding Block Sleeve 2
24 M10 x 3” Allen Bolt 2
25 Main Seat Support 1
26 M8 x 1” Allen Bolt 2
27 Seat Incline Adjustment 1
28 L-shaped Pin 1
29 Bearing 2
30 2” Square Sleeve 1
31 1 ¾” Square End Cap 1
32 Foam Roll Tube 3
33 Foam Roll 6
34 Foam Roll End Cap 6
35 4” Lock Pin 1
36 M12 x 2 3/8” Axle 1
37 Spring Clip Sleeve 2
38 Leg Developer 1
39 1 3/8” x 2 3/8” End Cap 2
40 Front Stabilizer 1
41 Leg Developer Holder 1
42 Rubber End Cap 1
43 Allen Set Screw 1
44 Spring Clip 1
45 M12 Allen Bolt 1
46 Handle Grip 2
9