INNOVAPLAS Lumi-O FIESTA 1003 User manual

REV. 04/04/2020 PN: PG:1
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
Fiesta Shell
A
x8 x8 x8
A B C
Contents of Accessory box 1003-HRK
SCREW BAG 140-0009
x8 x8 x8
(1 IN.)
(³⁄4 IN.)
x12
AB C D
x2
x2
x4
x4
x1
Required tools (not included)
Sand
(not included)
Sand
15 lbs
Phillips #2 Phillips #3 7/16 wrench
Phillips bit
3/8 drill bit
Security straps
x2
x2 x2 x2
(3/4 IN.)
x18
2 1/2 IN.)
x2
SCREW BAG 140-0058
(1 IN.)
EA D B C
Contents of the ladder box SKU # 6003
x2
x2
x2
x2
MAXIMUM functional
width is 1/4’’.
A weather-resistant
padlock is recommended
(not included).
FIESTA 1003 WITH CLASSIC LADDER 6003
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
1) Insert the four posts into
the step and secure them in
place with the bolts,
washers, and nuts
provided.
2) Insert the platform over
the two rear posts. Do not
secure.
3) Insert the small and large
handrails as illustrated.
Secure the large handrails
with the screws provided.
Leave the small handrails
floating.
Useful tip!
To ease the installation of
handrails and bolts, use a
Phillips screwdriver to line
up the holes.
x8
D
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM

REV. 04/04/2020 PN: PG:2
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
B
1) Insert the four Step Cups into
the holes under the step.*
x4
B2) With a flat screwdriver, compress the
Step Cup mushroom ring while pushing it
into the hole.
CAUTION
B1) Insert half of the Step Cup mushroom
ring in the hole, at a 45 degree angle.
D
*MINIMUM OF 1"
CAUTION To prevent pool liner puncture, keep a minimum 1" gap
between the pool liner and the rear underside of the step.
B3) Twist the Step Cup to ensure that
the mushroom ring has entirely cleared
the wall thickness. If it has, the suction
cup should rotate freely
C
Failing to install the Step Cup
TM
system will greatly reduce the steadiness of the step and
will void the manufacturer warranty.
Sand
15 LB
Align holes
1) Fill the ballast with sand. The
approximate weight should be
15 lbs.
2) Screw the lid in place and
align the cover ribs with the
holes in the ballast base.
3) Fasten the cover to the
ballast base with the four
screws provided.
x4
D
FIESTA 1003 WITH CLASSIC LADDER 6003
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1) Slowly submerge the step
into the pool. Make sure you do
not damage the pool liner
in the process.
2) Angle the whole step so that
it is entirely under water. Purge
all the air from under the steps.
3) Drop the ballast in the step
hole.
E
Security strap
1) Once the step is in
the pool secure the
platform to the top
seat (see illustration)
using the two straps
provided.
x2
OPTIONAL:
Once the pool step has
been completely
assembled and secured to
the pool, attach the two
screws supplied through
the platform to the top
seat of your pool to
provided a more rigid
assembly.
x2
E

REV. 04/04/2020 PN: PG:3
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
FIESTA 1003 WITH CLASSIC LADDER 6003
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
G
SWING THE LADDER UP
AND LOCK IN PLACE WHEN
THE POOL IS NOT IN USE
TO PREVENT DROWNING
AND UNAUTHORIZED
ENTRY.
WARNING
Use sliding lock as a guide to drill hole into
ladder in up position. Use a 3/8’’ drill bit with
a cordless drill.
**PADLOCK REQUIRED**
1) Attach the ladder to the pivot blocks with
the bolts, washers and nuts provided.
x2
x2
x2
A
B
C
F
E
1) Trace a line on each post at 39 inches from the
ground for 48’’ and 52’’ pools. If you have a 54’’ pool,
trace a line at 40.5 inches from the ground.
2) Slide the pivot blocks onto the posts and line up
with the traced marks. Secure with the screws
provided.
3) Attach the ladder base to the bottom of the posts
with the screws provided.
4) Slide the posts through the platform. Slide the lock
over right post between the platform and the handrail.
Secure the platform using the screws provided.
5) Slide the posts through the handrails. Insert the post
covers into the handrails. If they protrude too much,
raise the handrails until the post covers are seated
securely on the posts. Secure the short handrails in
place with the screws provided.
x18
D
A
D
align for 48''
& 52'' pools
align for 54’’
A
LOCK