INNOVAPLAS Lumi-O Biltmor 5005 User manual

REV. 12/10/2019 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
BILTMOR DECK 5005
A
2X
GUSSET
INSERT NUT
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Contents of the Biltmor box SKU # 5005
SCREW BAG 140-0021
WARNING
Required tools (not included)
Sand
(not included)
Sand
15 lbs
Sand
15 lbs
Phillips #2 Phillips #3
x4
x2
x2
x4 x2
x2
x6 x6 x6
(1 IN.)
(1 ¹⁄2 IN.)
(³⁄4 IN.)
x2
(³⁄4 IN.)
x24 x12
AB C D E F
x6 x6 x6
A B C
WARNING
Install the step on a flat surface.
Do not jump or dive from the step.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
7/16 wrench
Phillips bit

REV. 12/10/2019 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
BILTMOR DECK 5005
BC
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
D
E
F
G
1) Snap the four post ends into the
step, making sure that the cylindrical
part is vertical and that the ends are
snapped properly in their respective
housings.
2) Snap the two feet to the bottom of
the step.
1) Slowly submerge the
step into the pool. Make
sure you do not damage
the pool liner in the
process.
2) Angle the whole step
so that it is entirely under
water. Purge all the air from
under the steps.
’3
1/4
’
1/4’’
align screws from
center of plate
x20
x2
1) Insert the four posts into the post
ends and secure them in place with the
screws provided.
2) Insert the two deck supports over the
rear posts.
3) Insert the handrails on the four posts
and secure in place.
4)
Fasten the access panel with the screws
provided.
Sand
15 lbs
Sand
15 lbs
1) For installs where the deck support
is located more than 52" (132 cm)
from the bottom of the step, you can
add 2 15 lbs (7 kg) sand bags on
either side of the third step, as
shown.
2) Install the small post
covers.
1) Affix the deck supports
with the screws supplied.
1) Pull the deck
supports (already fixed
to the deck) upwards to
create a spring effect
on the step.
2) Fasten the supports
to the two rear posts
while pushing the entire
step downwards.
x4
F
x12
D
D
D
F
x3
D
E