INNOVAPLAS Fiesta User manual

REV. 03/05/2020 PN: PG:1
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
Fiesta Shell
A
x8 x8 x8
A B C
Contents of Accessory box 1001-HRK
SCREW BAG 140-0008
x2
x2
x4
x4
x1
x2
Required tools (not included)
Also needed but not included
Sand
15 lbs
Phillips #2 Phillips #3 7/16 wrench
Phillips bit
Contents of the Self-Latching box SKU # 9600
MAXIMUM functional
width is 1/4’’.
A weather-resistant
padlock is recommended
(not included).
FIESTA/OPERA WITH SELF-LATCHING 9600
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
1) Insert the four posts into
the step and secure them in
place with the bolts,
washers, and nuts
provided.
2) Insert the platform over
the two rear posts. Do not
secure.
3) Insert the small and large
handrails as illustrated.
Secure the large handrails
with the screws provided.
Leave the small handrails
floating.
Useful tip!
To ease the installation of
handrails and bolts, use a
Phillips screwdriver to line
up the holes.
x8
D
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
x8 x8 x8
(1 IN.)
(1 ¹⁄2 IN.)
(³⁄4 IN.)
x16 x12
AB C D E
Opera Shell
Security straps
x2
x2 x2
(3/4 IN.)
x12
(2 1/2 IN.)
x2
SCREW BAG 140-0016
(2 1/2 IN.)
FG D C
x2
x4
x3
Fiesta with Self-Latching

REV. 03/05/2020 PN: PG:2
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
B
1) Insert the four Step Cups into
the holes under the step.*
x4
B2) With a flat screwdriver, compress the
Step Cup mushroom ring while pushing it
into the hole.
CAUTION
B1) Insert half of the Step Cup mushroom
ring in the hole, at a 45 degree angle.
D
*MINIMUM 1"
CAUTION To prevent pool liner puncture, keep a minimum 1" gap
between the pool liner and the rear underside of the step.
B3) Twist the Step Cup to ensure that
the mushroom ring has entirely cleared
the wall thickness. If it has, the suction
cup should rotate freely
C
Failing to install the Step Cup
TM
system will greatly reduce the steadiness of the step and
will void the manufacturer warranty.
Sand
15 LB
Align holes
1) Fill the ballast with sand. The
approximate weight should be
15 lbs.
2) Screw the lid in place and
align the cover ribs with the
holes in the ballast base.
3) Fasten the cover to the
ballast base with the four
screws provided.
x4
D
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1) Slowly submerge the step
into the pool. Make sure you do
not damage the pool liner
in the process.
2) Angle the whole step so that
it is entirely under water. Purge
all the air from under the steps.
3) Drop the ballast in the step
hole.
E
Security strap
1) Once the step is in
the pool secure the
platform to the top
seat (see illustration)
using the two straps
provided.
x2
OPTIONAL:
Once the pool step has
been completely
assembled and secured to
the pool, attach the two
screws supplied through
the platform to the top
seat of your pool to
provided a more rigid
assembly.
x2
F
FIESTA/OPERA WITH SELF-LATCHING 9600

REV. 03/05/2020 PN: PG:3
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
FIESTA/OPERA WITH SELF-LATCHING 9600
H
F G
1) Insert the two posts into
the rear holes of the step.
2) Force the posts to a
vertical position flush with
the rear surface and
secure in place with the
bolts and nuts provided.
3) Insert the two post
covers.
x2
x2
G
C
1) Slide the Self-Latching
posts through the
platform and small
handrails.
2) Secure the platform
using the screws
provided.
3) Secure the small
handrails to the posts
with the screws provided.
4) Insert the four post
covers on the handrails.
x12
D
WARNING
LOCK THE DOOR TO THE
STEP WITH A PADLOCK
WHEN THE POOL IS NOT
IN USE TO PREVENT
DROWNING AND
UNAUTHORIZED ENTRY.