Cree lighting Stylus series User manual

Stylus Series

LED Ambient Luminaire

Ceiling/Surface Mount

1 of 6 LPN00644X0007A0_A

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

Installation Instructions are divided into

3 sections:

1. Surface Mounting - Individual Luminaire

2. Surface Mounting - Continuous Row

3. Electrical Connections

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant l’installation.

2. This luminaire must be installed in accordance with the NEC or your local

electrical code. If you are not familiar with these codes and requirements,

consult a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code électrique

local. Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez

contacter un électricien qualié.

3. SUITABLE FOR CONTINUOUS ROW MOUNTING.

PEUT ÊTRE MONTÉ EN RANGÉE CONTINUE.

4. Make sure the equipment is properly grounded.

5. Always de-energize the circuit and/or equipment before connecting to,

disconnecting from or servicing the equipment

SAVE THESE INSTRUCTIONS

FOR FUTURE REFERENCE

ST3-SF

NOTES:

• CAUTION - It is the installers responsibility to ensure that ceiling is structurally capable of supporting the weight of luminaire/luminaire row.

• Endcap kits and joining hardware are packaged separately for continuous rows.

• To Prevent Luminaire Row From Over-Current: By adding the input current of each luminaire section marked on the luminaire, the total current per

power feed must not exceed the maximum line wire amperage rating in the luminaire and the power feed cord/wire amperage rating whichever is

least.

2 of 6 LPN00644X0007A0_A

SECTION 1:

SURFACE MOUNTINGINDIVIDUAL LUMINAIRE

CAUTION: Luminaires should be secured

to structure above to support weight of

luminaire.

STEP 1:

Remove lens and LED/reflector tray and set

aside in order of run placement for reinstalling

later. To remove lens, carefully slide a plastic

card or putty knife between the lens and

extrusion towards the end of the luminaire.

Using the plastic card or putty knife, push the

lens inward until the lens comes free. See

Figure 1 and 2.

STEP 2:

After removing the lens, remove the Phillips

head reflector screws, remove the LED

Reflector Tray, and disconnect the LED

harness. Set lens and LED Reflector tray

aside. See Figure 1.

STEP 3:

Use the luminaire as a template to locate the

mounting holes by centering luminaire over

recessed switch box. Keep the switch box square

to and on center lengthwise, mark each mounting

anchors hole location, See Figure 2. Ensure that

all mounting points are on the same center line

as the switch box installed. Drill appropriate holes

for mounting surface and fasteners to be used.

Securely attach housing to ceiling: See Figure 1.

NOTE: Pre-drilled diameter 5/8" mounting

anchor holes are located 2.13" from the end

of each luminaire. See Figure 3 on the next

page.

STEP 4:

Using the 1.5” diameter hole located in the

center of the luminaire, route the electrical

leads out into customer supplied junction box

and make electrical connections per Section 3

“Electrical Connections”.

STEP 5:

Reconnect LED harness. Replace LED trays

and lens that was removed in Step 1 & 2

above, ensure that no wires are pinched.

Chalk Line

TO INSTALL:

Fasteners

(Supplied By Others)

Lens

Extrusion

Slide Plastic Card

or Putty Knife Here

Fasteners

LED Reflector

Tray

3 of 6 LPN00644X0007A0_A

2’ FIXTURE

4’ FIXTURE

8’ FIXTURE

12’ FIXTURE

6’ FIXTURE

10’ FIXTURE

LUMINAIRE ROW LAYOUT: SINGLE UNIT 2'  12'

***NOTE: Plugged holes provided for feed wire in the center of each luminaire.

24.25"

0.13" Endcap

Thickness

0.13"

48.25"

72.25"

96.25"

120.25"

144.25"

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

0.13" Endcap

Thickness

5/8" Mounting Anchor Holes

2” 1 1/2" Plugged Hole For Feed Wire

5/8" Mounting Anchor Holes

4 of 6 LPN00644X0007A0_A

SECTION 2: SURFACE MOUNTING  CONTINUOUS ROW MOUNTING

CAUTION: Ceiling contractor must provide

appropriate anchors to support weight of ceiling

mount linear luminaires.

CAUTION: Do not attempt to assemble

luminaire rows on the ground and then lift

into position. This may create stress at the

connection points and may result in damage

and/or mechanical failure.

CAUTION: Do not connect power in a run until

all of run is installed, wire harnesses connected,

and luminaire joints completed.

STEP 1:

From center line of lengthwise mounted switch

box(es), snap a lengthwise chalk line on ceiling

to the right of Junction box approximately the

full length of the row to be installed.

STEP 2:

Remove lens and upper LED/reflector tray

and set aside in order of run placement for

reinstalling later. To remove lens, carefully slide

a plastic card or putty knife between the lens

and extrusion towards the end of the luminaire.

Using the plastic card or putty knife, push the

lens inward until the lens come free. After

removing the lens, remove the Philips head

reflector screws, remove the LED Reflector Tray,

and disconnect the LED harness. Set lens and

LED Reflector tray aside. See Figure 1 and 2.

STEP 3:

Locate and install End Cap Kits. In order to install

the end cap on the male end of the luminaire,

replace the male joiner bracket with the female

joiner bracket and remove the alignment pins.

See Figure 4 and 6.

STEP 4:

Attach the first luminaire Right-Hand End of

the Row onto the ceiling per Figure 6. Tighten

mounting screws on luminaire snug as not to

allow luminaire to move when being aligned

with the next luminaire in the row.

STEP 5:

Position second luminaire in row such that it aligns

with joint end (male end) of first luminaire. Attach

using customer supplied hardware to structure

above. Connect the second luminaire to the first

luminaire as shown in Figure 5 and 6. Plug wire

harness together and push excess wire into

luminaire wiring chamber, ensure that wires are

not pinched.

STEP 6:

Push luminaires tightly together while making

sure the alignment pins slide into the interior

tracks of each luminaire and span the luminaire

joint. Secure joint by tightening supplied keps

locknuts on threaded studs of male joiner

bracket. Figure 5 and 6.

STEP 7:

Continue to install and assemble row following

steps 1-6 above. Locate and install Junction box

to be centered on the End unit (Left-Hand End of

Run) luminaire, make electrical connections per

Section 5 “Electrical Connections”.

STEP 7:

Replace LED trays and lens that was removed in

Step 1 above, ensure that no wires are pinched.

4 5

Alignment Pins

Male End

Female End

End Plate Cap (With

Alignment Pins)

End-Plate

Lock Nuts

5/8" Mounting Hole

Slide Screw w/

Lock Nuts

Female Joiner Bracket

First Luminaire

Chalk Line

Male End

Female End

Second Luminaire

5 of 6 LPN00644X0007A0_A

20’ FIXTURE

24’ FIXTURE

8’ UNIT

4’ UNIT

8’ UNIT

16’ FIXTURE

8’ UNIT 8’ UNIT

EXAMPLE 3 FIXTURE CONTINUOUS ROW

FEED LOCATION

Total Row Length (in) Endcap To Endcap

4' 6' 8'

Units End Cap

Kits

192.25

Feet

216.25

240.25

264.25

288.25

312.25

336.25

360.25

384.25

408.25

432.25

456.25

480.25

504.25

528.25

552.25

576.25

600.25

624.25

648.25

672.25

696.25

720.25

744.25

768.25

792.25

816.25

840.25

864.25

168.25

LUMINAIRE ROW LAYOUT: EXAMPLE OF A TWO AND THREE UNIT

16', 20'  24' (CAN BE MOUNTED IN OTHER CONFIGURATIONS)

96 -1/8" 96 -1/8”

192-1/4" End Cap to End Cap

48-1/8""

92” Mounting Center 92” Mounting Center

96 -1/8" 96 -1/8"

92” Mounting Center 92” Mounting Center 44” Mounting Center

96 -1/8" 96 -1/8" 96 -1/8"

92” Mounting Center 92” Mounting Center 92” Mounting Center

240-1/4" End Cap to End Cap

288-1/4" End Cap to End Cap

***NOTE: Plugged holes provided for feed wire in the

center of each luminaire.

6 of 6 LPN00644X0007A0_A

is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree®and the Cree logo are

registered trademarks of Cree, Inc.

www.creelighting.com

SECTION 5:

ELECTRICAL CONNECTIONS

STEP 1:

For 120/277/347V applications make the following Electrical

Connections:

a. Connect the black luminaire lead to the supply lead.

b. Connect the white luminaire lead to the neutral

supply lead.

c. Connect the green or green/yellow ground lead to

the green supply lead.

For 208/240V applications, make the following Electrical

Connections:

a. Connect Hot 1 supply lead to the black lead.

b. Connect Hot 2 supply lead to the white lead

c. Connect the green or green/yellow ground lead to

the supply ground lead.

STEP 2:

a. If Dimming is an option; connect the violet dimming

positive lead to the supply dimming positive lead. If

dimming is not being used, ensure to cap off the violet

lead.

b. If Dimming is an option; connect the grey dimming

negative lead to the supply dimming negative lead. If

dimming is not being used, ensure to cap off the grey

lead.

GREEN

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

DIM (-) GREY

DIM (+) VIOLET VIOLET

GREY

CORD/ SUPPLY WIRING

LUMINAIRE

NEUTRAL OR HOT 2

LINE OR HOT 1

FCC NOTICE

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user