Insignia KY001 Series User manual

www.insigniashowers.com Last Modied: 11/12/2023
INSTALLATION MANUAL
KY001 Infrared
Sauna Series
30 Day Technical Support:
Call 01908 317512 and request technical support for aiding your
installaon.
Replacements Parts: Inside of your warranty period visit:
hps://www.insigniashowers.com, click support and make a
warranty claim.
Spares/Replacements Parts: Outside of your warranty period visit
hps://www.insigniashowers.com/replacement-parts.html
ATTENTION INSTALLERS:
These instrucons must be
le with the customer CHECK ALL CONTENTS BEFORE BUILD COMMENCES. NO RETURNS CAN BE MADE
ONCE THE BUILD HAS STARTED AS IT IS DEEMED ACCEPTANCE OF PRODUCT!

www.insigniashowers.com Last Modied: 11/12/2023
02
Contents
Thank you for your purchase 3
Electrical & Tool requirements 4
Box contents 5
Screw Pack Contents 6
Sauna Side Panel and Back Panel Install 7
Side Panel Install 8
Bench Heater Install 9
Bench Seat Install 10
Back Rest Install 11
Door Frame Install 12
Heater Install 13
Roof Install 17
Corner Post Install 18
Door Handle Install 19
Securing the Electrics 20
Roof Cover Install 21
Electrical Connecons 22
Sauna Control Panel Instrucons 23
Remote Control Instrucons 24
Sauna Room Safety Guide 25
WEEE Compliance Statement 26

www.insigniashowers.com Last Modied: 11/12/2023
03
Thank you for your recent purchase of an Insignia Sauna. Please read this booklet with
great care to ensure you get the best out of your build and have a Sauna that will last
for many years to come! Like everything, in order to obtain a rst class product that
will serve you well for many years, the eort and correctness put into the assembly
will reect in the quality of your nish.

www.insigniashowers.com Last Modied: 11/12/2023
04
•Scissors
•Knife
•Spirit Level
•Tape Measure
•Philips Screwdriver
•Electric Drill
•Safety Gloves
•Safety Glasses
Tools Required
Voltage Rang 220-240AC
Frequency Rang 50Hz
Power Rang 1787 Was Sauna
Total Amperage 7.5amps
Indoor saunas with power consumpon under 3KW have been designed for easy installaon,
allowing for a simple plug-in directly into a standard household power circuit.
Installaon Notes:
1. (Recommended) Consult with a qualied Electrician before connecon to assess
suitability.
2. Ensure all parts are connected safely and correctly.
Always use protection against electrical surges by means of an RCD unit.
If you are uncertain about the installaon process or have any quesons, please feel
free to reach out to our friendly technical support for general advice. For anything more
specic to the electric installaon, please consult with a cered electrician.
Electrical Requirements Model KY001

www.insigniashowers.com Last Modied: 11/12/2023
05
What’s in the Boxes?
Contents Quanty
Roof
Le Panel
Back Panel
Right Panel
Front Panel Glass Door
Slaed Back Rest
Floor Insert
1
1
1
1
1
1
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
VERY IMPORTANT
Have you got everything? If not please contact the Insignia directly on 01908 317 512.
Remember NEVER book your tradesman unl everything has arrived, been checked and is
present. No replacement/missing parts can be obtained free of charge during or aer the
build. Any claims can only be within the mescale permied (48 hours aer delivery) and
always BEFORE build.
Contents Quanty
Door Handles
Bench Front Cover
Bench Top Cover
Heat Cover
Bench Frame
Roof Cover
Corner Posts
1
1
1
1
2
1
4
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]

www.insigniashowers.com Last Modied: 11/12/2023
06
Screw Pack Contents
Contents Quanty
ST 60mm Screws
ST 70mm Screws
ST 35mm Screws
ST 18mm Screws
ST 12mm Screws
Rubber pads for Heater
M 45mm Bolts
Wire Fixers
8
16
32
18
10
2
2
10
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
VERY IMPORTANT
Have you got everything? If not please contact the Insignia directly on 01908 317 512.
Remember NEVER book your tradesman unl everything has arrived, been checked and is
present. No replacement/missing parts can be obtained free of charge during or aer the
build. Any claims can only be within the mescale permied (48 hours aer delivery) and
always BEFORE build.

www.insigniashowers.com Last Modied: 11/12/2023
07
Step 1 — Installing the Back and Le Panels
4 x ST70mm Screws
Connect the le and back panels using the ST 70mm
screws found in the screw pack. Slot in the oor insert.

www.insigniashowers.com Last Modied: 11/12/2023
08
Step 2 — Installing the Right Panel
4 x ST70mm Screws
Repeat Step 1 with the right panel

www.insigniashowers.com Last Modied: 11/12/2023
09
Step 3 — Installing the Bench Heater
4 x ST18mm Screws
Using the ST 18mm screws found in the screw pack,
connect the bench heater behind the bench frame
as shown in the diagram.

www.insigniashowers.com Last Modied: 11/12/2023
10
Step 4 — Installing the Bench Seat
Once the bench panel is in place, locate the splier cable in the
screw bag & connect the heater wires as shown in the dia-
gram. The earth wire is secured on the back of the heater un-
der the bolt. Once installed, slot the bench top cover into

www.insigniashowers.com Last Modied: 11/12/2023
11
Step 5 — Installing the Back Rest
4 x ST35mm Screws
Install the back rest panel using the ST 35mm screws provided
in the screw pack.

www.insigniashowers.com Last Modied: 11/12/2023
12
Step 6 — Installing the Door Frame
4 x ST70mm Screws
Secure the front frame using the ST 70mm
screws supplied in the screw pack.

www.insigniashowers.com Last Modied: 11/12/2023
13
Step 7 — Installing the Heater
Screw the heater at the back of the heater cover using the ST
35mm screws.
4 x ST35mm Screws
4 x ST70mm Screws

www.insigniashowers.com Last Modied: 11/12/2023
14
Step 8 — Installing the Heater — connued
2 x ST70mm Screws
Hold the boom insert in place while securing with the ST
70mm screws.

www.insigniashowers.com Last Modied: 11/12/2023
15
Step 9 — Installing the Heater — connued
Once the heater has been screwed to the cover, connect the
wires into the backwall panel and screw in the earth wire.
Rest the heater on the boom insert, making sure the wires are
tucked underneath the slats.
(Above View)

www.insigniashowers.com Last Modied: 11/12/2023
16
Step 10 — Installing the Heater — connued
Firstly screw the heater to
the boom insert using the
ST 70mm screws.
6 x ST70mm Screws
Place the top insert on top the
heater and screw into place us-
ing the ST 70mm screws.
Lastly screw the heater into the
top insert upwards.

www.insigniashowers.com Last Modied: 11/12/2023
17
Step 11 — Installing the Roof
8 x ST60mm Screws
Carefully place the roof insert on the top of the sauna, holding in place
while securing with the ST 60mm screws provided in the screw pack.

www.insigniashowers.com Last Modied: 11/12/2023
18
Step 12 — Installing the Corner Posts
16 x ST35mm Screws
16 x Nuts and Washers
Connect the corner posts using the ST 35mm
screws and nuts and washers provided in the
screw pack as shown in the diagram.

www.insigniashowers.com Last Modied: 11/12/2023
19
Step 13 — Installing the Door Handle 2 x M45mm Screws
2 x Nuts and Washers
Connect the front piece and the rst part of the
back piece for the inside of the door, and ghten
using the nuts. Connect the second part of the
back piece and secure using the M 45 screws.

www.insigniashowers.com Last Modied: 11/12/2023
20
Step 14 — Securing the Electrics
10 x ST 12mm Screws
10 x Wire Securers
Secure the wires of the electrics on top of the roof using the wire xers.