Insignia MXOS1700 User manual

www.insigniashowers.com Last Modied: 20/12/2023
ATTENTION INSTALLERS:
These instrucons must be
le with the customer
30 Day Technical Support:
Call 01908 317512 and request technical support for aiding your
installaon.
Replacements Parts: Inside of your warranty period visit:
hps://www.insigniashowers.com, click support and make a
warranty claim.
Spares/Replacements Parts: Outside of your warranty period visit
hps://www.insigniashowers.com/replacement-parts.html
CHECK ALL CONTENTS BEFORE BUILD COMMENCES. NO RETURNS CAN BE MADE
ONCE THE BUILD HAS STARTED AS IT IS DEEMED ACCEPTANCE OF PRODUCT!
INSTALLATION MANUAL
MXOS1700—3rd Generaon
Hybrid Sauna

www.insigniashowers.com Last Modied: 20/12/2023
02
Contents
Thank you for your purchase 3
Electrical & Tool requirements 4
Box contents 5
Installing Instrucons 6
Creang the base 7
Installing the back panel 8
Installing the back le upright 9
Installing the right side panel 10
Installing the le side panel 11
Installing the two front posts 12
Installing the oor 13
Installing the electric box 14
Fing the top post beam 15
Installing the bench 16
Installing the bench seats 18
Installing the ed glass 19
Installing the inner roof 20
Installing the wall lamp 21
Installing the big roof 22
Installing the door 23
Installing the Door Handle 24
Installing the accessories 25
Stove installaon 26
Control Panel Instrucons/Operaon 27
Before First Use—IMPORTANT 30
Sauna Room Safety Guide 31
WEEE Compliance Statement 32

www.insigniashowers.com Last Modied: 20/12/2023
03
Thank you for your recent purchase of an Insignia Sauna. Please read this booklet with
great care to ensure you get the best out of your build and have a Sauna that will last
for many years to come! Like everything, in order to obtain a rst class product that
will serve you well for many years, the eort and correctness put into the assembly
will reect in the quality of your nish.
IMPORTANT!
OUTDOOR SAUNAS
CHOOSE BUILD DAYS WITH LOW HUMIDITY / NO RAIN / WET WEATHER IN COMING DAYS.
ALWAYS WOOD TREAT EXTERNAL PANELLING WITHIN 24 HOURS OF COMPLETION.
(Failure to do so can cause panel warp)

www.insigniashowers.com Last Modied: 20/12/2023
04
• Scissors
• Knife
• Spirit Level
• Tape Measure
• Philips Screwdriver
• Electric Drill
• Safety Gloves
• Safety Glasses
Tools Required
Stove
Harvia 4kW 240 volt 3 phase dedicated feed connecon or 240 volt single phase opon
Infrared Heaters
4 x 330 wa (1320 as total) 240 volt single phase connecon
Other
LED lighng, radio, Bluetooth etc 240 volt single phase 120 was
Total rang 5792 was
Amperage 24.2 amps
Always consult a qualied Electrician before connecon as to suitability Your electrical contractor will
understand ALL legal requirements of connecon before undertaking any work or installaon.
UNDER NO CIRCUMSTANCES UNDERTAKE THIS YOURSELF. ALWAYS USE AN ELECTRICAL
CONTRACTOR AND ENSURE LEGAL CERTIFICATION IS GIVEN ON COMPLETION
The MXOS1700 has provision for 240 volts. The 4kW stove has facility for the connecng opons. Your
qualied electrician will advise on the method they feel bests suits your situaon and electrical supply
along with any potenal benet either may have.
Electrics

www.insigniashowers.com Last Modied: 20/12/2023
05
What’s in the Boxes?
Contents Quanty
Back Panel
Le Panel
Side Panel
Fixed Glass
Door
Inner Roof
Big Roof
Sauna Heater
Heater tray
Heater Guard
1
1
1
1
1
1
1
1
1
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
VERY IMPORTANT
Have you got everything? If not please contact the Insignia directly on 01908 317 512.
Remember NEVER book your tradesman unl everything has arrived, been checked and is
present. No replacement/missing parts can be obtained free of charge during or aer the
build. Any claims can only be within the mescale permied (48 hours aer delivery) and
always BEFORE build.
Contents Quanty
Light
Door Handle
Sauna Rocks
Bench Top
Bench Vercal Supports
Under Bench Support
Screw Pack
1
1
1
1
1
1
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]

www.insigniashowers.com Last Modied: 20/12/2023
06
Please note : Like all mber products, such as garden sheds and fencing,
garden saunas require full exterior wood weatherproong treatment aer
installaon to ensure long life and prevenon of water ingress.
Maintenance Instructions
Installation Instructions
Please note : Must be installed on a solid and level base. Use bearers to allow gap to
prevent damp transfer.

www.insigniashowers.com Last Modied: 20/12/2023
07
Step 1 — Creang the base
Create a square using the 4 boom struts.
Note: The front strut has a groove cut out
for the front xed glass panel. Make sure
this strut is at the front of the square.

www.insigniashowers.com Last Modied: 20/12/2023
08
Step 2 — Installing the back panel
Place the back panel onto the base and slot
the right post beam up to lock in posion.

www.insigniashowers.com Last Modied: 20/12/2023
09
Step 3 — Installing the back le upright
Tilt the back panel up in order to get the back le upright to slot
into the brackets. Connect and push the le back upright down
and secure into posion.
There will be 3 screw connecons on two faces of the upright.
They should face towards the back boom strut and right boom
strut.

www.insigniashowers.com Last Modied: 20/12/2023
10
Step 4 — Installing the right side panel
Li the right side panel and slide the brackets
up the screw xings and lock into posion.
Also ensure you push the panel down onto
the right boom strut and ensure they lock
together.

www.insigniashowers.com Last Modied: 20/12/2023
11
Step 5 — Installing the le side panel
Li the le side panel and
slide the brackets up the
screw xings and lock into
posion. Also ensure you push
the panel down onto the le
boom strut and ensure they
lock together.

www.insigniashowers.com Last Modied: 20/12/2023
12
Step 6 — Installing the two front posts
Install the two front beams by sliding down the
slots and securing in posion ensuring they are
locked in the boom beam.

www.insigniashowers.com Last Modied: 20/12/2023
13
Step 7 — Installing the oor
Place the back part of the oor into posion
rst. This insert will have square cutouts which
are posioned towards the back of the sauna.
Place the front part of the oor into posion
next. This insert will have curved cutouts which
are posioned towards the front of the sauna.

www.insigniashowers.com Last Modied: 20/12/2023
14
Step 8 — Installing the electric box
Place the electric box on the oor of the sauna
and posion where the bench will enclose it.
Drill hole in the sauna wall to accommodate the
electric box cable.
Connect all electrics within the sauna.
Please note :
Once the connecons are made, ip the wooden
box over, ensuring no excess water enters the
electrics.

www.insigniashowers.com Last Modied: 20/12/2023
15
Step 9 — Installing the top beam
Locate the top framework into posion. Do not ghten unl the
next step as you need to li the framework slightly.

www.insigniashowers.com Last Modied: 20/12/2023
16
Step 10 — Installing the bench
Place the front bench piece in posion and screw into place.

www.insigniashowers.com Last Modied: 20/12/2023
17
Step 11 — Installing the bench—connued
Locate the bench support frame and screw into posion behind the
bench front piece.
Secure the bench front piece to the adjoining panels using the
screws.

www.insigniashowers.com Last Modied: 20/12/2023
18
Step 9 — Installing the bench seats
Locate the bench seat and slot into posion onto the bench front.

www.insigniashowers.com Last Modied: 20/12/2023
19
Step 12 — Installing the ed glass
Insert the xed glass into the groove cut-outs
in the framework, li the top framework up,
then slot back down once it is in posion.
Overhead view (right)
With the framework in posion ghten the nut and
washer from above.
Note: Be careful not to drop the hex nut and
washer down the upright.

www.insigniashowers.com Last Modied: 20/12/2023
20
Step 13 — Installing the inner roof
Locate the thermo probe and feed through the inner
roof. Please note you will need to pierce through the
insulaon to allow the thermo probe to be fed through
the roof. Secure in posion using silicone from above.
Ensure the probe extends approximately 75% out.
Ensure that the speakers are posioned towards the back. Please note
insulaon will need to be cut to allow bolts to secure. Once in posion,
take all cabling from the back and side panel and connect on top of the
inner roof.