Insignia KY2216 User manual

www.insigniashowers.com Last Modied: 07/02/2022
INSTALLATION MANUAL
KY2216
Sauna Series
ATTENTION INSTALLERS:
These instrucons must be
le with the customer CHECK ALL CONTENTS BEFORE BUILD COMMENCES. NO RETURNS CAN BE MADE
ONCE THE BUILD HAS STARTED AS IT IS DEEMED ACCEPTANCE OF PRODUCT!
30 Day Technical Support:
Call 01908 317512 and request technical support for aiding your
installaon.
Replacements Parts: Inside of your warranty period visit:
hps://www.insigniashowers.com, click support and make a
warranty claim.
Spares/Replacements Parts: Outside of your warranty period visit
hps://www.insigniashowers.com/replacement-parts.html

www.insigniashowers.com Last Modied: 07/02/2022
02
Contents
Thank you for your purchase 3
Electrical & Tool requirements 4
Box contents 5
Roof Connecon 6
Roof Lights Installaon 8
Roof Connecon 2 9
Floor Connecon 10
Back Panel Connecon 11
Side Panel Connecon 13
Right Side Panel to Back Panel Install 14
Le Side Panel Install 15
Lower Heater Guard Install 16
Heater Guard Install (Right Panel) 17
Heater Guard Install (Back Panel) 18
Upper Bench Install 19
Lower Bench Support Install 20
Lower Bench Install 21
Connecng the Front Framework 22
Framework Install 23
Door Handle Install 24
Door Hinge Install 25
Door Install 26
Heater and Heater Guard Install 27
Accessories Install 29
Electrical Connecons 30
Control Panel Instrucons 31
Sauna Room Safety Guide 33
WEEE Compliance Statement 34

www.insigniashowers.com Last Modied: 07/02/2022
03
Thank you for your recent purchase of an Insignia Sauna. Please read this booklet with
great care to ensure you get the best out of your build and have a Sauna that will last
for many years to come! Like everything, in order to obtain a rst class product that
will serve you well for many years, the eort and correctness put into the assembly
will reect in the quality of your nish.

www.insigniashowers.com Last Modied: 07/02/2022
04
• Scissors
• Knife
• Spirit Level
• Tape Measure
• Philips Screwdriver
• Electric Drill
• Safety Gloves
• Safety Glasses
Tools Required
Voltage Rang 220-240AC
Frequency Rang 50Hz
Power Rang 10880 Was
Amperage 45 .3 Amps
Always consult a qualied Electrician before connecon as to suitability
Always Obtain Relevant Cercaon (minor Works Part P etc)
This Sauna MUST NOT be directly connected to house sockets
Your electrical contractor will understand ALL legal requirements of connecon before undertaking any work or
installaon.
UNDER NO CIRCUMSTANCES UNDERTAKE THIS YOURSELF
Note for electrician:
1) Connect within current laws and IP direcves. Subject to room locaon.
2) (Preferred) Wire into isolated fused feed connecng directly to the house consumer/service box.
Always use protecon against electrical surge. Your shower should be treated the same as a home computer. A
surge protector should eradicate the possibility of either the transformer or control panel being burnt out.
Subject to connecon type, electrical work needs to be signed o by a fully qualied operave by law. Failure to
adhere to this will not only void your electrical warranty for your sauna, but could void your house insurance .
Electrical Requirements Model KY2216

www.insigniashowers.com Last Modied: 07/02/2022
05
What’s in the Boxes?
Contents Quanty
Inner Roof Piece
Floor Piece
Outer Roof Perimeter
Le Side Panel Piece
Right Side Panel Piece
Back Panel Piece
Heater Guard (Small)
Heater Guard (Medium)
Heater Guard (Large)
Heater
Sauna Rocks (Box)
Door Hinge
3
3
4
2
2
2
3
1
2
1
1
2
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
VERY IMPORTANT
Have you got everything? If not please contact the Insignia directly on 01908 317 512.
Remember NEVER book your tradesman unl everything has arrived, been checked and is
present. No replacement/missing parts can be obtained free of charge during or aer the
build. Any claims can only be within the mescale permied (48 hours aer delivery) and
always BEFORE build.
Contents Quanty
Front Framework Piece
Large Fixed Glass
Small Fixed Glass
Heater Guard
Door
Door Handle
Upper Bench
Lower Bench
Screw Pack
4
1
1
1
1
1
1
1
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]

www.insigniashowers.com Last Modied: 07/02/2022
06
Step 1 — Roof Connecon (Base)
8 x 60mm Screws
Locate the 3 roof panels and push them together. Use 8 ST60
Screws and screw the panels together.

www.insigniashowers.com Last Modied: 07/02/2022
07
Step 2 — Roof Connecon (Outer Square)
8 x 60mm Screws
Locate the 4 outer roof perimeter panels and
push them together. Screw 2 ST60 screws in each
corner to secure it together.

www.insigniashowers.com Last Modied: 07/02/2022
08
Step 3 — Roof Lights Installaon
Locate the LED light strip and place around the
inside lip of the outer roof perimeter rectangle.
Locate the securing clips and
screw them into the inner
roof lip to secure the LED
strip into posion.
The LED strip locaon is denoted by the red
dashed line. The circuit of lights will start and end
at this corner as shown.

www.insigniashowers.com Last Modied: 07/02/2022
09
Step 4 — Roof Connecon
12 x 60mm Screws
Place the outer roof perimeter rectangle face down and overlay
the roof and screw them together using ST60 screws.

www.insigniashowers.com Last Modied: 07/02/2022
10
Step 5 — Floor Connecon
12 x 60mm Screws
Locate the 3 oor panels and push them together. Use 8 ST60
Screws and screw the panels together.

www.insigniashowers.com Last Modied: 07/02/2022
11
Step 6 — Back panel connecon
Locate the 2 back panels and the top/boom connecng wooden struts.
The top strut has two grooves cut out for wires to feed through.
The boom strut has plasc feet connected to enable manoeuvrability of the
sauna
Overhead view
Push the panels together, interlocking the grooved cut-outs shown.
Tip: Lay the back panels at for connecon.

www.insigniashowers.com Last Modied: 07/02/2022
12
Step 7 — Back panel connecon
10 x 60mm Screws
Push the boom strut into the connected panels
and screw in posion using 5 ST60 Screws.
Rotate the top strut so the grooves are facing towards the back of the panel.
Push into the connected panels and screw in posion using 5 ST60 Screws.

www.insigniashowers.com Last Modied: 07/02/2022
13
Step 8 — Side Panel connecon
10 x 60mm Screws
Repeat the process from the previous step for the right
hand side panel.
Note the right side panel features the control panel.
Once the right panel has been connected, locate the
remaining side panel pieces and connect

www.insigniashowers.com Last Modied: 07/02/2022
14
Step 9 — Connecng right side panel to the back panel.
Li the side panel and locate the connecon brackets.
Once the brackets have been located, pull down on the
side panel to secure into posion.

www.insigniashowers.com Last Modied: 07/02/2022
15
Step 10 — Connecng le side panel to the back panel.
Li the side panel and locate the connecon brackets.
Once the brackets have been located, pull down on the
side panel to secure into posion.

www.insigniashowers.com Last Modied: 07/02/2022
16
Step 11 — Installing the lower heater guards (back panel)
Locate the four small rectangle heater guards and x them
to the back panel over the horizontal sauna heaters. Use a
spirit level to align and x in place using 16 x ST50 Screws
16 x 50mm Screws

www.insigniashowers.com Last Modied: 07/02/2022
17
Step 12 — Installing the heater guards (right panel)
Locate the heater guards for the triple heater and single
heater, align with a spirit level and screw in posion using
4 ST70 Screws per heater guard.
Locate two more single heater guards for the le side
panel and secure into posion.
16 x 70mm Screws

www.insigniashowers.com Last Modied: 07/02/2022
18
Step 13 — Installing the heater guards (back panel)
Locate the two large heater guards for the double heaters
in the back panel, align with a spirit level and screw in
posion using 4 ST70 Screws per heater guard.
8 x 70mm Screws

www.insigniashowers.com Last Modied: 07/02/2022
19
Step 14 — Installing the upper bench
Locate the upper bench and slide it into posion. The bench will sit on
the upper bench supports located on the back panel and each side
panel. Once in posion secure in place using 6 ST70 screws.
6 x 70mm Screws

www.insigniashowers.com Last Modied: 07/02/2022
20
Step 15 — Installing the lower bench support
6 x 70mm Screws
Locate the lower bench support beams, align with a spirit level and screw
one to each side panel using 3 ST70 Screws. Ensure both supports are
posioned at the same height so the lower bench sits at.