Insignia KY3000 Series User manual

www.insigniashowers.com Last Modied: 16/03/2022
INSTALLATION MANUAL
KY3000
Sauna Series
30 Day Technical Support:
Call 01908 317512 and request technical support for aiding your
installaon.
Replacements Parts: Inside of your warranty period visit:
hps://www.insigniashowers.com, click support and make a
warranty claim.
Spares/Replacements Parts: Outside of your warranty period visit
hps://www.insigniashowers.com/replacement-parts.html
ATTENTION INSTALLERS:
These instrucons must be
le with the customer CHECK ALL CONTENTS BEFORE BUILD COMMENCES. NO RETURNS CAN BE MADE
ONCE THE BUILD HAS STARTED AS IT IS DEEMED ACCEPTANCE OF PRODUCT!

www.insigniashowers.com Last Modied: 16/03/2022
02
Contents
Thank you for your purchase 3
Electrical & Tool requirements 4
Box contents 5
Roof Connecon 6
Back Panel Connecon 9
Side Panel Install 10
Bar Install 11
Curved Front Fixed Panel Install 12
Door Frame Install 13
Floor posioning 14
Lower Heater Guard Install 15
Upper Heater Guard Install 16
Bench Framework Install 17
Bench Seat Install 18
Bar Front Install 19
Roof Install 21
Electrics Install 22
Roof Topper Install 23
Door Handle Install 24
Control Panel Instrucons 25
Sauna Room Safety Guide 26
WEEE Compliance Statement 27

www.insigniashowers.com Last Modied: 16/03/2022
03
Thank you for your recent purchase of an Insignia Sauna. Please read this booklet with
great care to ensure you get the best out of your build and have a Sauna that will last
for many years to come! Like everything, in order to obtain a rst class product that
will serve you well for many years, the eort and correctness put into the assembly
will reect in the quality of your nish.

www.insigniashowers.com Last Modied: 16/03/2022
04
• Scissors
• Knife
• Spirit Level
• Tape Measure
Tools Required
Voltage Rang 220-240AC
Frequency Rang 50Hz
Power Rang 6097 Was
Amperage 25.404 amps
Always consult a qualied Electrician before connecon as to suitability
Always Obtain Relevant Cercaon (minor Works Part P etc)
This Sauna MUST NOT be directly connected to house sockets
Your electrical contractor will understand ALL legal requirements of connecon before
undertaking any work or installaon.
UNDER NO CIRCUMSTANCES UNDERTAKE THIS YOURSELF
Note for electrician:
1) Connect within current laws and IP direcves. Subject to room locaon.
2) (Preferred) Wire into isolated fused feed connecng directly to the house consumer/service
box.
Always use protecon against electrical surge. Your shower should be treated the same as a
home computer. A surge protector should eradicate the possibility of either the transformer or
control panel being burnt out.
Subject to connecon type, electrical work needs to be signed o by a fully qualied operave
by law. Failure to adhere to this will not only void your electrical warranty for your sauna, but
could void your house insurance
Electrical Requirements Sauna Model No KY3000
You will require:
• Philips Screwdriver
• Electric Drill
• Safety Gloves
• Safety Glasses

www.insigniashowers.com Last Modied: 16/03/2022
05
What’s in the Boxes?
Contents Quanty
Back Wall (three pieces)
Floor (three pieces)
Roof (four pieces)
Side Panel
Panel Connectors
Bar
Bar front
Bar Floor
Door Handle
Heater Guard
Screw Pack
1
1
1
2
2
1
1
1
1
9
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
VERY IMPORTANT
Have you got everything? If not please contact the Insignia directly on 01908 317 512.
Remember NEVER book your tradesman unl everything has arrived, been checked and is
present. No replacement/missing parts can be obtained free of charge during or aer the
build. Any claims can only be within the mescale permied (48 hours aer delivery) and
always BEFORE build.
Contents Quanty
Bar Support
Bench Legs
Bench Frame
Bench Top
Curved Front Fixed Glass Panel
Front Frame/Door
Roof Topper (four pieces)
1
4
3
3
2
1
1
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]

www.insigniashowers.com Last Modied: 16/03/2022
06
Step 1 — Connecng the Roof
5 x 60mm Screws
Locate the roof pieces and posion together and
secure by screwing together using ST60 Screws.

www.insigniashowers.com Last Modied: 16/03/2022
07
Step 1 — Connecng the Roof connued
5 x 60mm Screws
Locate the roof pieces and posion together and
secure by screwing together using ST60 Screws.

www.insigniashowers.com Last Modied: 16/03/2022
08
Step 1 — Connecng the Roof connued
5 x 60mm Screws
Locate the roof pieces and posion together and
secure by screwing together using ST60 Screws

www.insigniashowers.com Last Modied: 16/03/2022
09
Step 2 — Le side panel and back panel connecon
Locate the three back panel pieces, two top bar
connectors and two boom bar connectors. The
top bar connectors have grooves cut out for the
wires. Slot the back panels together and push the
to and boom connectors in. Screw the top and
boom connectors in using ST60 Screws
12 x 60mm Screws

www.insigniashowers.com Last Modied: 16/03/2022
10
Step 3 — Back panel to side panel connecon
Locate the screw xings and screw them into the
side panel.
Li the side panel and locate the screw xing and
recessed bracket together and push the panel down
to lock it into posion.

www.insigniashowers.com Last Modied: 16/03/2022
11
Step 4 — Bar Panel Install
Locate the screw xings and screw them into the
side panel.
Li the bar panel and locate the screw xing and
recessed bracket together and push the panel down
to lock it into posion.

www.insigniashowers.com Last Modied: 16/03/2022
12
Step 5 — Front curved panel install
Locate the screw xings and screw them into the
right side panel and the bar panel.
Li the curved xed glass panels and locate the
screw xing and recessed bracket together and push
the panel down to lock it into posion.

www.insigniashowers.com Last Modied: 16/03/2022
13
Step 6 — Door Install
Locate the screw xings and screw them into both
curved xed glass panels.
Li the door and locate the screw xing and
recessed bracket together on both sides and push
the door down to lock it into posion.

www.insigniashowers.com Last Modied: 16/03/2022
14
Step 7 — Floor posioning
Locate the three oor pieces and
posion into the sauna.

www.insigniashowers.com Last Modied: 16/03/2022
15
Step 7 — Lower heater guard install
16 x 35mm Screws
Locate the four lower heater covers and screw them
in posion using ST35 Screws.

www.insigniashowers.com Last Modied: 16/03/2022
16
Step 8 — Upper heater guard install
20 x 35mm Screws
Locate the ve upper heater covers and screw them
in posion using ST35 Screws.
Note: The heater panels are dierent sizes:
• Le side panel = 940mm
• Back panel (le guard) = 1040mm
• Back panel (middle guard) = 460mm
• Back panel (right guard) = 1040mm
• Right side panel = 1220mm

www.insigniashowers.com Last Modied: 16/03/2022
17
Step 9 — Bench framework install
20 x 35mm Screws
Locate the bench legs and support
framework and place into posion. The
unique bench leg sits centrally on the back
panel bench framework.
The bench legs have cut-outs for the bench
support to t around. The leg posioning is
highlighted.
Secure the bench framework by screwing to
the legs and panels all around using ST35
Screws.

www.insigniashowers.com Last Modied: 16/03/2022
18
Step 10 — Bench Top install
Locate the bench tops and place into posion.

www.insigniashowers.com Last Modied: 16/03/2022
19
Step 11 — Bar Install
Locate the screw xings and screw them into
the door frame.
Li the bar front, locate the screw xing and recessed
bracket together on the door panel and the bar sides and
push the door down to lock it into posion.

www.insigniashowers.com Last Modied: 16/03/2022
20
Step 12 — Bar Topper and Support Install
Place the Bar Topper on the Bar body and locate the ‘L’
shaped support brackets and screw to the underside of
the bar topper using ST12 Screws.
Locate the cylindrical
upright and place on top
of the bar in the groove
that is recessed. Screw
from underneath to
secure in posion using
an ST60 Screw.