Insportline Oberon 4464 User manual

User’s manual – EN
IN 4464 Up-right bike inSPORTline Oberon

Safety Instructions
• To ensure the best safety of the exerciser, regularly
check it on damages and worn parts.
• If you pass on this exerciser to another person or if
you allow another person to use it, make sure that
that person is familiar with the content and
instructions in these instructions.
• Only one person should use the exerciser at a time .
• Before the first use and regularly make sure that all
screws, bolts and other joints are properly tightened
and firmly seated.
• Before you start your work out, remove all
sharp edged objects around the exerciser.
• Only use the exercise for your work out if it works
flawlessly.
• Any broken, worn or defective part must immediately
be replaced and/or the exerciser must no longer be
used until it has been properly maintained and
repaired.
• Parents and other supervisory persons should be
aware of their responsibility, due to situations which
may arise for which the exerciser has not been
designed and which may occur due to children’s
natural play instinct and interest in experimenting.
• If you do allow children to use this exerciser, be sure
to take into consideration and assess their mental
and physical condition and development, and above
all their temperament. Children should use the
exerciser only under adult supervision and be
instructed on the correct and proper use of the
exerciser. The exerciser is not a toy.
• Make sure there is sufficient free space around
the exerciser when you set it up.
• To avoid possible accidents, do not allow children
to approach the exerciser without supervision,
since they may use it in a way for which it is not
intended due to their natural play instinct and
interest in experimenting.
• Please note that an improper and excessive
work out may be harmful to your health.
• Please note that levers and other adjustment
mechanisms are not projecting into the area of
movement during the work out.
• When setting up the exerciser, please make
sure that the exerciser is standing in a stable
way and that any possible unevenness of the
floor is evened out.
• Always wear appropriate clothing and shoes
which are suitable for your work out on the
exerciser. The clothes must be designed in a
way so that they will not get caught in any part
of the exerciser during the work out due to their
form (for example, length). Be sure to wear
appropriate shoes which are suitable for the
work out, firmly support the feet and which are
provided with a non slip sole.
• Be sure to consult a physician before you start
any exercise program. He may give you proper
hints and advice with respect to the individual
intensity of stress for you as well as to your
work out and sensible eating habits.

Important Notes
• Assemble the exerciser as per assembly instructions
and be sure to only use the structural parts provided
with the exerciser and designed for it. Prior to the
assembly, make sure the content of the delivery is
complete by referring to the parts list of the
assembly and operating instructions.
• Be sure to set up the exerciser in a dry and even
place and always protect it from humidity. If you wish
to protect the place particularly against pressure
points, contamination, etc., it is recommended to put
a suitable, non slip mat under the exerciser.
• The general rule is that exercisers and training
devices are no toys. Therefore, they must only be
used by properly informed or instructed persons.
• Stop your work out immediately in case of dizziness,
nausea, chest pain or any other physical symptoms. In
case of doubt, consult your physician immediately.
• Children, disabled and handicapped persons should
use the exercise only under supervision and in
presence of another person who may give support
and useful instructions.
• Be sure that your body parts and those of other
persons are never close to any moving parts of the
exerciser during its use.
• When adjusting the adjustable parts, make sure
they are adjusted properly and note the marked,
maximum adjusting position, for example of the
saddle support, respectively.
• Do not work out immediately after meals!

Exploded Drawing
19
2
51 53
75
69
66
74
73
70
71
72
59
58
61
60 63
62
3
4
5
10
11
9
6
7
8
12
15
13
14
47
48
49
16R
86R
16L
17 20 21 18 24
1
26
28
27
25
29
32
40
39
35
30
31
37
363438
33
22
23 42
41
43
50
54
55
56 57 49 48
65
64
67
68
46
7776 78 79 80
80 81
8583 84
86L
45
44

Part List
Part No.
Description Qty Part No.
Description Qty
1 Main frame 1 45 Cross screw ST4.2x1.4x20L 9
2
Balling knob
D50xM16x22xD8 1 46 Handlebar post 1
3 Inner plug D66xD52x170L 1 47 Inner allen bolt M8*1.25*20L 4
4
Idle fixed plate
155*62.2*5T 1 48
Spring washer D15.4
XD8.2x2T 8
5 Inner allen bolt M10*35L 1 49
Curved washer
D22*D8.5*1.5T 8
6 Bushing D20*D14*11.5T 1 50 Stabilizer 40*80*1.5T*480L 1
7 Idle wheel D23.8xD38x24 1 51 Stabilizer 40*80*1.5T*480L 1
8 Nylon nut M10x1.5x10T 1 53 Front foot cap 1
9 Spring D2.2*D14*65 1 54 Front foot cap 1
10 Allen bolt M8*1.25*30L 1 55 Adjustable foot cap 2
11
Plastic flat washer
D10*D24*0.4T 2 56
Square neck bolt
M8*1.25*55L 4
12
Flat washer
D30*D8.5*2.0T 1 57 Domed nut M8*1.25*15L 4
13 Allen nut M8*1.25*6T 1 58 Seat 1
14 Nylon nut M8*1.25*8T 1 59
Seat adjustable tube welding
set 1
15 Plastic cover D4*30L 2 60 Seat tube welding set 1
16L Left crank 6 1/2"x9/16" 1 61 End cap 25*50*32L 2
16R Right crank 6 1/2"x9/16" 1 62 Flat washer D28*D8.5*3T 1
17 C ring S 17(1T) 1 63 Knob D60x32L(M8x1.25) 1
18
Flat washer
D23*D17.2*1.5T 1 64 Flat washer 3
19 Bearing #6003ZZ 2 65 Nylon nut 3
20
Waved wahser
D22xD17x0.3T 2 66 Handlebar 1
21 Bushing D22.5*D17.2*6.4T
1 67 Foam D20*7T*620L 2
22 Allen bolt M8x1.25x25( 2 68 End cap D7/8"x20L 2
23 Bolt cover D23x6.5 2 69 Hand pulse TP 012,直立式 2
24 Crank bearing welding set 1 Pulse cable 600L 2
25 Belt PJ5 1092L 1 70 T knob M8x1.25x65 1
26 Belt wheel D280*21 1 71 Flat washer D16xD8.5x1.2T 1
27 Allen bolt M6x1.0x15L 4 72 Spring washer
D15.4xD8.2x2T 1
28 Nylon nut M6x1.0x6T 4 73 Bushing D8.2xD12.7x33 1
29 Flywheel 1 74 Protective cover 1
30
Anit lose nut
3/8" 26UNFx6.5T 2 75 Computer TZ 6139P 1

31 Bolt cover D35*8 1 76 Upper computer cable 1000L 1
Part No. Description Qty Part No. Description Qty
32 Magnetic fixed plate 1 77 Lower computer cable 1250L 1
33 Spring D1.2*55L 1 78 Round magnetic 1
34 Flat washer D13*D6.5*1.0T
1 79 Sensor cable 150L 1
35 Allen bolt M6*65L 1 80 Cross screw M5x0.8x12L 1
36
Nylon washer
D6*D19*1.5T 1 81 Motor 1
37 Allen nut M6*1*6T 1 82 Cross screw ST4.2*1.4*15L 4
38 Nylon nut M6*1*6T 1 83 Electric cable 1
39 Allen bolt M8*52L 1 84 Tension cable D1.5*260L 1
40 Nylon nut M8*1.25*8T 1 85 Adaptor 1
41 Left chain cover 1 86L/R Pedal 1
42 Right chain cover 1 Inner allen cross spanner 1
43 Round cover 2 Spanner 1
44 gasket around cover 1

Chec List
X 4
56
X 1
X 1
X 4
47
X 8
48
X 8
49
X 4
57
M8*1.25*20L D15.4*D8.2*2T D22*D8.5*1.5T
M8*1.25*55L M8*15L
1
X 1
51
50
X 1
X 1
58
46 74 50
59 73
72
71
70
75 85
86L&R
60
X 1
X 1
X 1
X 1
X 1
X 1 X 1
X 1
X 1
X 1 X 1

Step 1
50
57
49
48
51
56
M8*15L
M8*55L D15.4
D22
x4
56 49 48 57
A
1
Assemble the front stabilizer (51) and the rear stabilizer (50) on the main frame (1) by using
the Square nec bolt (56), the Domed nut (57), the spring washer (48) and the curved
washer (49).

Step 2
63
62
64
60
B
DOWN
UP
BACKWARD
FRONTWARD
A
B
x3
65
64
58
59
1
1) Assemble the seat (64) on the seat adjustable tube (60) by using the flat washer (62)
and the nob (63).
2) Insert the seat post welding sets (60) into the main frame (1) and use the ball
quic -release nob (2) to loc the seat post.
3) The seat (64) could be adjusted to different heights by rotating the ball quic -release
nob (2), and adjusted bac ward and frontward.

Step 3
47
48
49
46
76
77
M8*20L D15.4 D22
x4
56 4948
C
1) Assemble the handlebar post (46) on the main frame (1) by using the curved washer
(49), spring washer (48) and the inner allen bolt (47).
2) Connect the upper computer cable (46) and lower computer cable (47).