Insportline AX1001 User manual

HOME FITNESS GYM
AX1001
ASSEMBLY INSTRUCTIONS

EXPLODED DIAGRAM

PART LIST
NUMBER DESCRIPTION QUANTITY
1 LEFT BASE 1
2 RIGHT BASE 1
3 LEFT MAIN UPRIGHT 1
4 RIGHT MAIN UPRIGHT 1
5 REAR LEFT UPRIGHT 1
6 REAR RIGHT UPRIGHT 1
7 LEFT SLIDE FRAME 1
8 RIGHT SLIDE FRAME 1
9 GUIDE ROD 4
10 SHORT GUIDE ROD 2
11 PLATE SUPPORT 2
12 TOP FRAME 2
13 BOTTOM CROSS FRAME 1
14 MIDDLE CROSS FRAME 1
15 TOP CROSS FRAME 1
16 WEIGHT BAR 1
17 PULL BAR 1
18 LEFT SUPPORT 1
19 RIGHT SUPPORT 1
20 LEFT HOLD SUPPORT 1
21 RIGHT HOLD SUPPORT 1
22 LEFT BARBELL SUPPORT 1
23 RIGHT BARBELL SUPPORT 1
24 LEFT SLIDER 1
25 RIGHT SLIDER 1
26 DOUBLE PULLEY BRACKET 2
27 SLIDE SUPPORT 2
28 LEFT HOOK 1
29 RIGHT HOOK 1
30 BAR HOLDER 1
31 SINGLE PULLEY BRACKET 2
32 PLATE BAR 2
33 OLYMPIC PLATE BAR 6
34 SHORT OLYMPIC PLATE BAR 2
35 CLOSED HOOK 1
36 HOOK 4
37 ROTATION SUPPORT 1
38 BAR SUPPORT 1
39 AXIS 1
40 BUSHING 2
41 CIRCLE HOOK 2

42 REINFORCEMENT PLATE 4
43 REINFORCEMENT PLATE 6
44 M10 BOLT CAP 2
45 ROUND PLUG 8
46 RUBBER CIRCLE 8
47 RUBBER BUMPER 6
48 SPIRNG CLIP-REGULAR 8
49 SPIRNG CLIP-OLYMPIC 8
50 LOCK PIN 2
51 BEARING 2
52 CIRCLE FOR HOLE 2
53 PULLEY 16
54 LARGE PULLEY 2
55 NYLON BUSHING 1
56 CLIP 2
57 CABLE 2
58 PLUM SHAPED SCREW 1
59 SLIDER PIN 2
60 M8*8 SOCKET SCREW 2
61 M10*16 SOCKET CAP SCREW 4
62 M10*25 SOCKET CAP SCREW 14
63 M10*30 HEXAGONAL HEAD SCREW 2
64 M10*50 SOCKET CAP SCREW 18
65 M10*70 SOCKET CAP SCREW 20
66 M10*75 SOCKET CAP SCREW 20
67 M10*105 SOCKET CAP SCREW 2
68 M12*105 SOCKET CAP SCREW 1
69 10MM WASHER 138
70 12MM WASHER 2
71 M8 LOCK NUT 2
72 M10 LOCK NUT 58
73 M12 LOCK NUT 1
74 M12 NUT 2
83 HOLDER 2
84 PULL PIN 4
85 FOAM ROLLER 2
86 FOAM COVER 2
87 CABLE STOPPER 4

STEP 01
1．Attach the right main upright (4) and reinforcement plate (43) to the right base (2) using two
M10*75 screws (66), four 10mm washers (69) and two M10 lock nuts (72).
2．Attach the rear right upright (6) and reinforcement plate (43) to the right base (2) using two
M10*75 screws (66), four 10mm washers (69) and two M10 lock nuts (72).
3．Attach the top frame (12) to the right main upright (4) using two M10*70 screws (65), two
M10*16 screws (61), six 10mm washers (69) and two M10 lock nuts (72).
4．The assembly step of left side is the same as the right one. (STEP 01)

STEP 02
1. Attach the bottom cross frame (13) and reinforcement plate (42) to rear left and right upright
(5、6) using four M10*70 screws (65), four M10*75 screws (66), sixteen 10mm washers (69)
and eight M10 lock nuts (72).
2. Attach the middle cross frame (14) and reinforcement plate (42) to rear left and right upright
(5、6) and top frame (12) using four M10*75 screws (66), four M10*25 screws (62), twelve
10mm washers (69) and four M10 lock nuts (72).
3. Attach the top cross frame (15) and reinforcement plate (43) to top frame (12) using four
M10*70 screws (65), eight 10mm washers (69) and four M10 lock nuts (72).
4. Attach the closed hook (35) to the top cross frame (15) using 10mm washers (69) and M10
lock nut (72).
5. Insert one holder (83) into hole on the middle cross frame (14).

STEP 03
1. Slide the left and right hook (28、29) onto the weight bar (16).
2. Slide the slide support (27) onto the weight bar (16).
3. Insert the short guide rod (10) into hole of the slide support (27) and rubber bumper (47),
attach the short guide rod (10) to the left and right main upright (3、4) and the top frame (12)
using four M10*70 screws (65) and four 10mm washers (69).
4. Hook the left and right hook (28、29) to left and right main upright (3、4) and secure with
M8*8 screw (60).
5. Slide the left and right slider (24、25) onto the left and right slide frame (7、8), secure with
slider pin (59).
6. Attach the double pulley bracket (26) to the left and right slider (24、25) using bushing (40),
two M10*105 screws (67), four 10mm washers (69) and two M10 lock nuts (72).
7. Attach the left slide frame (7) to the left base (1) and top frame (12) using two M10*75
screws (66), four 10mm washers (69) and two M10 lock nuts (72).
8. Attach the right slide frame (8) to the right base (2) and top frame (12) using two M10*75
screws (66), four 10mm washers (69) and two M10 lock nuts (72).

STEP 04
1. Attach the bar holder (30) to rear left upright (5) using two M10*30 screws (63) and two
10mm washers (69). Push the M10 bolt cap (44) onto screws (63).
2. Slide rubber bumper (47) and the plate support (11) onto the guide rod (9). Insert the guide
rod (9) into hole of the left and right base (1、2) and secure the rod to the top frame (12) using
four M10*70 screws (65) and four 10mm washers (69).
3. Attach the plate bar (32) to the rear upright (5、6) using two M10*25 screws (62) and two
10mm washers (69).
4. Slide the Olympic plate bar (33) onto the weight bar (16), the plate support (11) and the plate
bar (32), secure with six M10*25 screws (62) and six 10mm washers (69). Slide the short
Olympic plate bar (34) onto the plate support (11), secure with two M10*25 screws (62) and
two 10mm washers (69). Push round plug (45) into Olympic plate bars (33、34).
5. Attach the hooks (36) to the bottom and middle cross frame (13、14) using four M10 lock
nuts (72) and four 10mm washers (69).
6. Thread a nut M12 (74) onto the singe pulley bracket (31). Insert the singe pulley bracket (31)
into the plate support (11). Do not tighten! This will be adjusted later.
7. Attach sixteen pulley (53) and two large pulley (54) into the pulley brackets using eighteen
screws M10*50 (64), thirty-six 10mm washers (69) and sixteen M10 lock nuts (72). The top
four pulleys have cable stopper (87).

STEP 05
1. Attach the rotation support (37) and nylon bushing (55) to main upright (3、4) or slide frame
(7、8) use axis (39). Then lock with lock pin (50).
2. Attach the bar support (38) to the rotation support (37) using M12*105 screw (68), two
12mm washers (70) and M12 lock nut (73).
3. Attach the plum shaped screw (58) to the bar support (38).
4. Attach the left and right barbell support (22、23), the left and right hold support (20、21) and
the left and right support (18、19) to slide frame (7、8).
5. Lock the left and right barbell support (22、23), the left and right hold support (20、21) with
pull pin (84).

STEP 06
Bring the threaded end of the cable (57) from A→B→C→D→E→F→G→H→24.
NOTE: From F→G, the cable is IN the tube.
Repeat the steps to route the cable through the right tower.
Attach the pull bar (17) to cables (57) with clip (56).