Insportline 18259 User manual

USER MANUAL –EN
IN 18259 Leg Extension Machine Steelflex PlateLoad Line
PLLE

2
CONTENTS
SAFETY INSTRUCTIONS....................................................................................................................... 3
DIAGRAM................................................................................................................................................ 4
CONNECTION MATERIAL ..................................................................................................................... 5
PARTS LIST............................................................................................................................................ 6
ASSEMBLY ........................................................................................................................................... 10
EXERCISE INSTRUCTIONS ................................................................................................................ 14
ENVIRONMENT PROTECTION ........................................................................................................... 15
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS................................................. 15

3
SAFETY INSTRUCTIONS
Please read the manual carefully before using the equipment and keep it for future reference.
•Read the manual carefully before assembly and using the device to avoid injury. Instruct other
users about security.
•Consult your physician before starting exercise. Your physician can advise you on the optimal
load and exercise frequency. Improper use can lead to injury. Consult your condition if you are
taking medicines or have an injury.
•If you experience nausea or another anomaly, stop exercising. Do not exercise if you feel:
chest pain or tension, irregular heartbeat, shortness of breath, nausea or if you are dizzy. If
you observe any health problems, contact your doctor immediately.
•The device may only be used by adults. Do not keep children or pets unattended around the
device.
•Place the machine on a flat and solid surface. Use a protection mat to protect the floor. Keep
away from other equipment in the room min. 0.6 m.
•Make sure all screws are properly tightened before using the device. Replace damaged parts
or worn parts immediately. Proper maintenance will extend the life of the equipment.
•No adjustable part can prohibit movement of user.
•Use the device only in accordance with the manual. Replace worn parts immediately. Do not
exercise on damaged equipment.
•Wear suitable clothes during exercise. Avoid too loose clothes that is easy to be stuck. Wear
sport shoes.
•Do not use the device outdoors or near water.
•The device is not suitable for therapeutic purposes.
•Do not exercise on the device for about 1 hour before and after a meal.
•Before starting an exercise, do warm up exercise.
•Be careful not to injure your back or other body when moving the machine. If necessary, ask
another adult for help.
•Weight: 75 kg
•Maximum user weight: 120 kg
•Weight limit of one arm: 150 kg
•Dimension: l 131 cm × w 126 cm × h 103 cm
•For Olympic weights (50 mm).
•Suitable for commercial and non-commercial use.

4
DIAGRAM

5
CONNECTION MATERIAL
A1. Hex head bolt M10 x 75 –15 pcs
A2. Hex head bolt M10 x 60 –1 pcs (pre-assembled)
A3. Allen screw M10 x 20 –6 pcs (pre-assembled)
A4. Hex head bolt M8 x 75 –3 pcs
A5. Allen screw M8 x 45 –4 pcs
A6. Hex head bolt M8 x 25 –4 pcs
A8. Stud bolt M5 x 5 –18 pcs (pre-
assembled)
A9. Allen screw M8 x 30 –2 pcs
A10. Stud bolt M6 x 6 –8 pcs (pre-
assembled)
B1. Safety nut M10 –16 pcs (pre-assembled
–1 pcs)

6
C1. Washer M10 (Ø 27) –6 pcs (pre-
assembled)
C2. Washer M10 (Ø 19) –2 pcs
C3. Washer M10 (Ø30) –28 pcs
C4. Washer M8 (Ø24) –7 pcs
C5. Spring washer M8 –9 pcs
C6. Spring washer M10 –4 pcs (pre-
assembled)
PARTS LIST
A –1 pcs
B –1 pcs
C –1 pcs
D –1 pcs
E –1 pcs
H –1 pcs

7
F –1 pcs
I –1 pcs
K –1 pcs
M –2 pcs (6730002)
D –7 pcs (8323188)
Q –1 pcs (9111072)
P –1 pcs (9121077)
N –1 pcs (8830023) (pre-assembled)

8
NO
Name
QTY
D1
Copper washer (8520-007)
2
D2
Chrome sleeve (8890-061) –pre-assembled
2
D3
Steel rope (8890-068)
1
D4
End cap (9211-016)
2
D5
End cap (9211-074)
4
D6
End cap (9211-086)
2
D7
End cap 50 x 50 (9211-087)
2
D8
End cap (9211-092)
1
D9
End cap 40 x 80 (9211-113) –pre-assembled
4
D10
End cap 50 x 100 (9211-114)
3
D11
Nylon Washer (9214-008)
2
D12
Rubber base plate (9310-016)
4
D13
Rubber base plate (9310-076)
4
D14
Rubber base plate (9310-078)
2
D15
Safety sleeve (OC-06)
2
D16
Screw head cover (9212-026)
28
D17
Bearing (8510-048) –pre-assembled
4
D18
Nylon insert (9211-047)
1
D19
Foam roller (9161-009)
2

9
D20
End cap (8130-253) –pre-assembled
2
D21
End cap (8130-249) –pre-assembled
2
D22
Axis (8220-184) –pre-assembled
2
D23
Flat safety pin (8250-122G) –pre-assembled
2
D24
Flat safety pin (8250-125) –pre-assembled
1
D25
Chrome protection (8520-003) –pre-assembled
4
D27
Chrome protection (8890-069) –pre-assembled
2
D28
Lever (8890-070) –pre-assembled
1
D29
Foam grip (9162-002) –pre-assembled
2
D30
Foam grip (9162-103) –pre-assembled
2
D31
End cap (9211-157)
2
D32
Pulley spacer (8530-009) –pre-assembled
2
D33
Logo (9260-023) –pre-assembled
2
D34
Pulley spacer (8110-079)
2

10
ASSEMBLY
Step 1
Above shows STEP 1 assembled and completed.