IPC CT46B User manual

CT46 B - C Quick Guide
This Guide is intended for quick consultation only and does not replace the Use and Maintenance
Manual. Before using the machine, read the Use and Maintenance Manual contained in the machi-
ne packaging thoroughly and rigorously respect all the instructions.
PREPARATION/
OPERATION
Fill the detergent tank. Press the ON button.
Press the brush button to activate
suction and water delivery.
Operate the drive lever.
Begin working.
When you have nished cleaning,
proceed as follows:
• Press the brush button.
• Turn the machine off by pres-
sing the ON button for at least 4
seconds.
• Raise the squeegee.
• Close the detergent tank tap.
• If needing to recharge the batte-
ries, connect the power cable to
the battery charger or connect the
external battery charger to the
connecter highlighted in the photo.
Adjust the slope of the handle by pul-
ling the handle release lever.
Open the detergent tank tap.
DAILY MAINTENANCE
Empty the dirty water tank.
Clean the dirty water tank.
Lower the squeegee using the lever.
1
PLDC03819
IP Cleaning S.p.A. - Viale Treviso, 63 30026 Summaga di Portogruaro - www.ipcworldwide.com

CT46 B - C Quick Guide
THE MACHINE DOES NOT
COME ON/START UP
CHECK THE BATTERY CHARGE (BATTERY VERSION)
CHECK THE POWER CABLE IS PLUGGED INTO A FUNCTIONING SOCKET (CABLE
VERSION)
THE MACHINE LEAVES THE
FLOOR WET
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THERE IS NO DEBRIS IN THE SUCTION HOSE
CHECK THE DIRTY WATER TANK IS NOT FULL
CHECK THE DETERGENT TANK LID IS CLOSED CORRECTLY
CHECK THE SUCTION HOSE IS CORRECTLY ATTACHED TO THE SQUEEGEE
THE MACHINE LEAVES THE
FLOOR DIRTY
CHECK THE TYPE OF BRUSH IN USE IS SUITABLE FOR THE TYPE OF DIRT AND
FLOOR.
THE MACHINE LEAVES
STRIPES OF WET FLOOR
CHECK THE FLOOR HAS BEEN BRUSHED BEFORE USING THE MACHINE
CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES
CHECK THE SQUEEGEE BLADES ARE NOT WORN
CHECK THE SQUEEGEE IS CORRECTLY ADJUSTED
Check the detergent output lter is
undamaged and clean.
Clean the brush. Check the battery charge (BATTERY
VERSION).
If needing to recharge the batteries,
connect the power cable to the battery
charger or connect the external battery
charger to the connecter highlighted in
the photo.
Check the squeegee is clean and the
blades are not damaged.
Check the dirty water tank oat is un-
damaged and clean and moves freely
on the pin.
REPLACING THE SQUEEGEE BLADES
• Release the clip
• Remove the two blade retainers by pushing them towards the outside of the squeegee then extracting them.
• Remove the blade.
• Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it
onto the screws on the body of the squeegee.
• Reposition the two blade retainers by centring the widest part of the slots over the xing screws on the squeegee body, then pushing the blade
retainers inwards.
• Fasten the clip.
AUTOMATIC BRUSH ATTACHMENT
Attaching the brush:
• rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, cen-
tring it with the brush cover. Action the drive lever repeatedly until the brush engages..
Removing the brush:
• Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the
brush is released and falls to the ground..
2
PLDC03819
IP Cleaning S.p.A. - Viale Treviso, 63 30026 Summaga di Portogruaro - www.ipcworldwide.com