IRSAP THE RADIATOR COMPANY Athena User manual

The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company notied
within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be tted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been tted. This
includes any consequential loss or cost of tting.
If The Radiator Company are not notied within 28 days of the date on the signed delivery note then it
will be deemed that The Radiator Company have fully complied with its obligations and claims will not
be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging to
prevent damage prior to installation. The Radiator Company cannot accept responsibility for items
damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make over to
you the benet of any warranty or guarantee given by the manufacturer, which is usually ve years on
most of our range. (Copies of specic guarantees for any of our products are available on request).
The guarantees in all cases are subject to the products being installed in accordance with British and or
European standards as well as these tting instructions. The guarantees in all cases are restricted to the
free of charge replacement or repair of the failed product only. Our liability will under no circumstances
extend beyond the repair or replacement of the product supplied by us. Claims for either labour in
replacement or damage to property are not admissible. Any goods that are returned, in the event of a
problem, will belong to The Radiator Company.
Technical Specications
Please read these instructions and terms and
conditons carefully prior to installation.
Failure to do so may invalidate the warranty
Athena
horizontal
Fittings Instructions
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
THE
RADIA
TOR
COMPANY
ATHEH_IR_1.0
PLEASE NOTE: Systems using micro bore pipework must have adequate pressure and ow rates
for the number and style of radiators on the system.
Materials Steel
Connections 1/2” ow and return, underneath connections
Test Pressure 6 Bar
Testing Authority EN442
Maximum operating pressure 4 Bar
Maximum working temperature 95oC
Packaging Polystyrene protection in cardboard box
If you have any questions please contact us: 01342 302250, www.theradiatorcompany.co.uk A brand of , Italy’s leading manufacturer of design led radiators

Diagrams of Athena Horizontal Pipe Centres Fix Brackets
3
PLEASE NOTE:
It is essential that all brackets are
level to ensure a vertical alignment for
connecting the pipework.
Hang Radiator & Commission
4
Please Note:
In accordance with Part L1 2006 of the Building Regulations
and BS7593:1992 code of practice for the treatment of hot
water and central heating systems, we strongly recommend
flushing the heating system post installation of new radiators
and then adding the correct quantity and type of inhibitor
for use with your radiator and system to prevent corrosion.
Damage caused to systems not protected by a suitable
inhibitor will not be covered by manufacturer’s guarantee.
Unpack & Inspect
1
You should have:
• 1 Radiator
• 4 Wall bracket Nipples
• 4 Wall brackets Sleeves
• 4 Grub Screws
• 1 Airvent
• 1 Blanking Plug
You will need:
• Tape measure
• Electric drill
• Suitable drill bit and plugs
• Spirit level
Contents
2
The Radiator Company prides itself on selecting products
from manufacturers who exercise tight quality control
measures.
We only select models with excellent standards of welding
and brazing, as well as high quality finishes.
All of our products are well packaged and should reach
you in perfect condition. Just in case however, we offer a
minimum 5-year no quibble guarantee for all radiators and
towel rails.
The Radiator Company must be notified of any shortages or
damage within 28 days of delivery.
For further information please see
terms and conditions on back page.
Pipe centres left to right width minus 70mm
Pipe centres from wall 45mm to 53mm
Depth from wall 67mm to 75mm
1. Insert bracket nipples into threaded holes on the back of
the radiator.
2. The fixing positions for the two top brackets are measured
down 77.5mm from the top of the radiator and 35mm
in from the edges of the radiator. Mark the positions on
the wall and hold up your radiator to check the positions.
3. Ensure the markings are level, and using a suitable drill bit
and plugs, fix the top two bracket sleeves to the wall.
4. For accuracy, we suggest hanging the radiator on the top
two brackets, then marking the bottom bracket positions.
5. Remove the radiator off the wall and fix the bottom two
brackets to the wall.
6. Hold up the radiator to the wall and slot the four bracket
nipples into the bracket sleeves.
7. Use the provided grub screws to secure the radiator by
inserting and tightening on the side of the brackets.
35
77.5
Bracket Positions
35
77.5
77.5
35
77.5
35
67-75
45-53

The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company
notified within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be fitted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been fitted.
This includes any consequential loss or cost of fitting.
If The Radiator Company are not notified within 28 days of the date on the signed delivery note
then it will be deemed that The Radiator Company have fully complied with its obligations and
claims will not be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging
to prevent damage prior to installation. The Radiator Company cannot accept responsibility for
items damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make
over to you the benefit of any warranty or guarantee given by the manufacturer, which is usually
five years on most of our range. (Copies of specific guarantees for any of our products are
available on request).
The guarantees in all cases are subject to the products being installed in accordance with British
and or European standards as well as these fitting instructions. The guarantees in all cases are
restricted to the free of charge replacement or repair of the failed product only. Our liability will
under no circumstances extend beyond the repair or replacement of the product supplied by us.
Claims for either labour in replacement or damage to property are not admissible. Any goods
that are returned, in the event of a problem, will belong to The Radiator Company.
Technical Specications
Please read these instructions and terms and
conditons carefully prior to installation.
Failure to do so may invalidate the warranty
Athena Vertical
Fittings Instructions
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
ATHEV_IR_1.0
PLEASE NOTE: Systemsusingmicroborepipeworkmusthaveadequatepressureandowratesfor
the number and style of radiators on the system.
Materials Steel
Connections 1/2”owandreturn
Test Pressure 6 Bar
Testing Authority EN442
Maximum operating pressure 4 Bar
Maximum working temperature 95oC
Packaging Polystyrene protection in cardboard box
If you have any questions please contact us: 01342 302250, www.theradiatorcompany.co.uk A brand of , Italy’s leading manufacturer of design led radiators
THE
RADIATOR
COMPANY

Diagrams of Athena Vertical Pipe Centres Fix Brackets
3
PLEASE NOTE:
It is essential that all brackets are
level to ensure a vertical alignment for
connecting the pipework.
Hang Radiator & Commission
4
Please Note:
In accordance with Part L1 2006 of the Building Regulations
and BS7593:1992 code of practice for the treatment of hot
water and central heating systems, we strongly recommend
flushing the heating system post installation of new radiators
and then adding the correct quantity and type of inhibitor
for use with your radiator and system to prevent corrosion.
Damage caused to systems not protected by a suitable
inhibitor will not be covered by manufacturer’s guarantee.
Unpack & Inspect
1
You should have:
• 1 Radiator
• 4 Wall bracket Nipples
• 4 Wall brackets Sleeves
• 4 Grub Screws
• 1 Airvent
• 1 Blanking Plug
You will need:
• Tape measure
• Electric drill
• Suitable drill bit and plugs
• Spirit level
Contents
2
The Radiator Company prides itself on selecting products
from manufacturers who exercise tight quality control
measures.
We only select models with excellent standards of welding
and brazing, as well as high quality finishes.
All of our products are well packaged and should reach
you in perfect condition. Just in case however, we offer a
minimum 5-year no quibble guarantee for all radiators and
towel rails.
The Radiator Company must be notified of any shortages or
damage within 28 days of delivery.
For further information please see
terms and conditions on back page.
Pipe centres left to right width minus 70mm
Pipe centres from wall 45mm to 53mm
Depth from wall 67mm to 75mm
1. Insert bracket nipples into threaded holes on the back of
the radiator.
2. The fixing positions for the two top brackets are measured
down 77.5mm from the top of the radiator and 35mm in
from the edge of the radiator. Mark the positions on the
wall and hold up your radiator to check the positions.
3. Ensure the markings are level, and using a suitable drill bit
and plugs, fix the top two bracket sleeves to the wall.
4. For accuracy, we suggest hanging the radiator on the top
two brackets, then marking the bottom bracket positions.
5. Remove the radiator off the wall and fix the bottom two
brackets to the wall.
6. Hold up the radiator to the wall and slot the four bracket
nipples into the bracket sleeves.
7. Use the provided grub screws to secure the radiator by
inserting and tightening on the side of the brackets.
35
77.5
Bracket Positions
67-75
45-53
77.5
35
77.5
35
77.5
35