IRSAP THE RADIATOR COMPANY Ceres User manual

1
2
”
All products must be inspected once removed from the packaging and The Radiator Company
notified within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be fitted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been fitted.
This includes any consequential loss or cost of fitting.
If The Radiator Company are not notified within 28 days of the date on the signed delivery note
then it will be deemed that The Radiator Company have fully complied with its obligations and
claims will not be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging
to prevent damage prior to installation. The Radiator Company cannot accept responsibility for
items damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make
over to you the benefit of any warranty or guarantee given by the manufacturer, which is usually
five years on most of our range. (Copies of specific guarantees for any of our products are
available on request).
The guarantees in all cases are subject to the products being installed in accordance with British
and or European standards as well as these fitting instructions. The guarantees in all cases are
restricted to the free of charge replacement or repair of the failed product only. Our liability will
under no circumstances extend beyond the repair or replacement of the product supplied by us.
Claims for either labour in replacement or damage to property are not admissible. Any goods
that are returned, in the event of a problem, will belong to The Radiator Company.
Technical Specications
The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
Please read these instructions and terms and
conditions carefully prior to installation.
Failure to do so may invalidate the warranty.
Materials Stainless Steel.
Connections ow and return.
Test pressure 5.2 Bar
Testing authority EN442
Maximum operating pressure 4 Bar
Maximum working temperature 90ºC
Packaging Covered with Polystyrene in a Cardboard box.
Cleaning Use provided cleaning glove or a soft cloth with a
propietary stainless steel cleaning product
This slim prole radiator appears to oat off the
wall.
Ceres
Fittings Instructions
10
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
THE
RADIATOR
COMPANY
CERE2.2
PLEASE NOTE: Systems using micro bore pipework must have adequate pressure and
ow rates for the number and style of radiators on the system.
PLEASE NOTE : This radiator can
be heavy and requires a minimum
of two people to t, on a suitable
wall structure.
If you have any questions please contact us: 01342 302250, www.theradiatorcompany.co.uk A brand of , Italy’s leading manufacturer of design led radiators

Unpack & Inspect
1
4
Contents
5
Diverter
3
Diagrams of Ceres
The Radiator Company prides itself on selecting products from
manufacturers who exercise tight quality control measures. We
only select models with excellent standards of welding and
brazing, as well as high quality nishes. All of our products are
well packaged and should reach you in perfect condition. Just in
case however, we offer a minimum 5-year no quibble guarantee
for all radiators and towel rails.
Please carefully unpack and inspect this radiator and all ttings.
The Radiator Company must be notied of any shortages or
damage within 28 days of delivery. For further information please
see terms and conditions on back page.
Pipe Centres
Commission
Pipe centres left to right width + valves
Pipe centres from wall 55mm to 80mm
Depth from wall 80mm to 105mm
Please Note: In accordance with Part L1 2006 of the Building
Regulations and BS7593:1992 code of practice for the treatment
of hot water and central heating systems, we strongly recommend
flushing the heating system post installation of new radiators and
then adding the correct quantity and type of inhibitor for use with
your radiator and system to prevent corrosion. Damage caused to
systems not protected by a suitable inhibitor will not be covered
by manufacturer’s guarantee.
• 4 wall brackets sleeves
• 4 grub screws
• 2 airvents
1. Loosely attach the bracket sleeves to the xed bracket studs.
2. Position the radiator against the wall and mark the location
of the top bracket sleeves; approx 45mm in from each corner and
25mm down from the top (see diagram opposite).
3. It is essential to accurately
mark these positions as there is
little tolerance for movement on the
brackets. Check the positions are
level and then using the appropriate
drill bits, screws and plugs t the top
wall bracket sleeves.
4. Re-position the radiator
inserting the studs into the top
bracket sleeves, check it is level and
then mark the location of the bottom
bracket sleeves approx 45mm in from
each corner and 25mm up from the
bottom (see diagram opposite).
5. Then using the appropriate drill
bits screws and plugs t the bottom
wall brackets sleeves to the wall and
use a spirit level to check they are
horizontally level.
6. Insert the bracket studs into the
bracket sleeves and secure using the
grub screws provided on the side of
the bracket sleeve.
PLEASE NOTE:
It is essential that all brackets are level to ensure a vertical
alignment for connecting the pipework and that xings are suitable
for the wall material.
2
The Ceres radiator has a diverter tted
on the left hand side (see digrams) to
ensure the correct ow of water, this
should always be at the return end on
the bottom collector.
Fix Brackets and Hang
4
45
25
45
25
25
45
25
45
25
55 to 80
80 to 105
Wall xings are supplied but are
not suitable for all wall types.
Please use suitable xings.
X
X=diverter position
To locate the diverter, look through the end of the bottom collectors;
one will be clear and one will have a blockage (the diverter).
owreturn
continued...