IRSAP THE RADIATOR COMPANY ISEO TRC-IS-O30 User manual

Materials Aluminium
Connections ow and return.
Test pressure 9 Bar
Testing authority EN442
Maximum operating pressure 6 Bar
Maximum working temperature 90 ºC
Packaging Polystyrene Protection in cardboard box
1
2
”
The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company
notified within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be fitted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been fitted.
This includes any consequential loss or cost of fitting.
If The Radiator Company are not notified within 28 days of the date on the signed delivery
note then it will be deemed that The Radiator Company have fully complied with its
obligations and claims will not be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging
to prevent damage prior to installation. The Radiator Company cannot accept responsibility
for items damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make
over to you the benet of any warranty or guarantee given by the manufacturer, which is usually
ve years on most of our range. (Copies of specic guarantees for any of our products are
available on request).
The guarantees in all cases are subject to the products being installed in accordance with British
and or European standards as well as these tting instructions. The guarantees in all cases are
restricted to the free of charge replacement or repair of the failed product only. Our liability will
under no circumstances extend beyond the repair or replacement of the product supplied by us.
Claims for either labour in replacement or damage to property are not admissible. Any goods
that are returned, in the event of a problem, will belong to The Radiator Company.
Technical Specications
Please read these instructions and terms and conditions carefully
prior to installation. Failure to do so may invalidate the warranty
Iseo
Fittings Instructions
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
THE
RADIATOR
COMPANY
ISEO_IR_1.0
PLEASE NOTE: To reduce the possibility of noise caused by rapid heating and cooling
of aluminium radiators; adequate capacity for expansion must be provided within
the overall heating system. Systems using micro bore pipework must have adequate
pressure and flow rates for the number and style of radiators on the system.
If you have any questions please contact us: 01342 302250, www.theradiatorcompany.co.uk A brand of , Italy’s leading manufacturer of design led radiators

Unpack & Inspect
1
Contents
2
Hanging the Radiator
4
Drawing 1 - Fixing positions for brackets
The Radiator Company prides itself on selecting products from
manufacturers who exercise tight quality control measures. We
only select models with excellent standards of welding and
brazing, as well as high quality finishes. All of our products are well
packaged and should reach you in perfect condition. Just in case
however, we offer a minimum 5-year no quibble
guarantee for all radiators and towel rails.
The Radiator Company must be notified of
any shortages or damage within 28 days of
delivery. For further information please see
terms and conditions on back page.
Pipe Centres
Pipe centres left to right
Pipe centres from wall
Depth from wall
Commission
5
Please Note:
In accordance with Part L1 2006 of the Building Regulations
and BS7593:1992 code of practice for the treatment of hot
water and central heating systems, we strongly recommend
flushing the heating system post installation of new radiators
and then adding the correct quantity and type of inhibitor
for use with your radiator and system to prevent corrosion.
Damage caused to systems not protected by a suitable
inhibitor will not be covered by manufacturer’s guarantee.
Width + Valves
38mm - 52mm
111mm - 121mm
Please refer to diagrams opposite when following steps below:
Identifying the Diverter
3
Insert the rubber diverter inside the bottom collector on the flow
side. Using a hex key press approx. 150 mm into the collector (Note
the bottom collector has no hole drilled for the air vent).
.
Fig.1 Bracket Positions (mm)
You will need:
• Tape measure
• Electric drill and bits
• Spirit level
• Airvent key
• Appropriatewallxings
• Spanner for valves & vents
You should have:
• 1 Radiator
• 4 Brackets
• 2 Blanking plugs
• 1 airvent
• 1 Rubber Diverter
1. Accurately mark bracket holes on the wall using a tape
measure and spirit level. The bracket centres are positioned
43mm down from the top of the radiator, and 82.5mm in from
either side. (Height of the radiator from floor: minimum 100mm)
2. Drill holes using suitable drill bits and plugs, insert suitable
wall plugs. To hang the top two brackets, secure the backplate
‘A’ with screws ‘B’ (or other suitable screws) going through into
the wall plugs.
3. Select the pipe distance from wall using options 1A,1B,2A or
2B and Insert the brackets ‘C’ down into the back plate ‘A’ and
secure with the provided screw ‘D’. Then fit the closing cap ‘E’
on top.
4. Hang the radiator and mark the bottom on the wall, take
down the radiator and fit the bottom two brackets with back
plate centred 14mm above the mark (Note the bottom back
plate will be below the radiator) Using the same option as used
on top brackets regarding distance from wall repeat “3”
82,5 82,5
46
14
b
Fig 3. Bracket Hanging measurements
45,76 50,56
Fig 2. Bracket Hanging options
Option. 1
Option. 2
Option. 1
12,05
9,75
A
B
4 pz.
C
D
E
A
B
40,7535,95
Option. 2A Option. 1A
Option. 2B Option. 1B
43
10,50
11,50
47,30 51,50
36,50 41,30