ISHIDA SR-2000 alpha User manual

Automatic Scale Register
SR-2000α
USER’S MANUAL
CAUTION
READ AND UNDERSTAND THIS MANUAL
•Thoroughly read and understand this manual before installing, operating, inspecting, and
servicing the machine.
•Keep this manual in a safe place where you can refer to it whenever necessary.
•Consult your ISHIDA representative if you have any questions or comments.
PN 89061

2004 ISHIDA Co., Ltd.
COPYRIGHT AND COPY PERMISSION
This manual shall not be copied without permission.
This manual is protected by copyright and is intended solely for use in conjunction with the machine.
Please notify us before copying or reproducing this manual in any manner, for any other purpose.
© ISHIDA CO., LTD., 2004

SAFETY PRECAUTIONS
SAFETY PRECAUTIONS
Important Notice
Those who handle the machine must be aware of the hazards involved. These dangers may not be
obvious, so it is imperative to follow the instructions detailed in this manual when installing, operating,
inspecting, or servicing the machine. Therefore, we recommend that you thoroughly read and
understand this manual before installing, operating, inspecting, or servicing the machine.
ISHIDA is not liable for any damage, loss or injury that results from incorrect operation, insufficient
caution, unauthorized modifications to the machine, or failure to follow the instructions contained in
this manual.
In the recent weighing industry, the latent hazards involved with handling the machine have increased
due to new materials, new processing methods, and higher processing speeds, and it is impossible to
predict all of the possible dangers.
Likewise, there are far too many operations which cannot or should not be performed to fully describe
all of them in the manual. Please assume that any operation not specifically described in this manual
should never be performed.
Safety countermeasures should be carefully considered and implemented before performing any
installation, operation, inspection, or maintenance procedure not specifically described in this manual
or indicated on the machine itself.
Change in Specifications
Machine specifications and accessories may be changed at any time due to improvements or other
reasons. Consult with your ISHIDA representative at any time to confirm the actual specifications of
the purchased machine.
Errors and Omissions
The information in this manual has been carefully checked and is believed to be accurate; however,
no responsibility is assumed for clerical, typographical or proofreading errors, or omissions.
Limitations of Liability
ISHIDA assumes no responsibility for special, indirect, or consequential damages, loss of profits or
commercial loss in any way connected with the machine, whether such claim is based on contract,
warranty, negligence, or strict liability.
ISHIDA shall assume responsibility for problems with the machine or the system based on an
individual maintenance contract. However, ISHIDA shall not be responsible for secondary problems.
ISHIDA assumes no responsibility for the user's programming of this machine, or any consequence
thereof.
In no event shall ISHIDA be responsible for warranty, repair, or other claims regarding the machine
unless ISHIDA’s analysis confirms that the machines were properly handled, stored, installed, and
maintained and not subject to contamination, abuse, misuse, or inappropriate modification or repair.
Tornado and Compact-VJE are used in this machine.•
•
•
Tornado is a trademark of Wind River Systems, Inc.
Compact-VJE is a trademark of VACS Corporation.
SR-2000αUser’s Manual (No. 0000A) i

SAFETY PRECAUTIONS
Meanings of Signal Words
This machine is manufactured for use according to proper procedures by a qualified person and only
for the purposes described in this manual. The following conventions are used to indicate and classify
precautions depending on the level of danger, or seriousness of potential injury. Always heed the
information provided in this manual. Failure to heed precautions can result in personal injury or
property damage.
The following signal words are used in this manual.
Indicates a potentially hazardous situation which, if not avoided, will result in
minor or moderate injury, or may result in serious injury or death. Additionally,
there may be significant property damage
Indicates a potentially hazardous situation where, if not avoided, may result
in minor or moderate injury or in property damage.
ii SR-2000αUser’s Manual (No. 0000A)

SAFETY PRECAUTIONS
Precautions for Safe Use
Do not allow the machine, terminals, etc. to
come in contact with water.
Doing so may result in fire or cause the machine to
break down.
Do not give a strong shock to the machine as it
is a precision machine.
Doing so may cause the machine to break down.
Do not disassemble, modify, or attempt to repair
the machine.
Doing so may damage the original safety functions.
Do not hold the cover when carrying the
machine.
Dropping the machine may result in injury or cause
the machine to break down.
Do not hold the operation panel when carrying
the machine.
Doing so may cause the operation panel to break
down.
Do not drop the cassette.
Dropping the cassette may result in injury or cause
the cassette to break down.
•
•
•
•
•
•
SR-2000αUser’s Manual (No. 0000A) iii

SAFETY PRECAUTIONS
Handle with care when removing or inserting the
cassette.
Careless cassette handling may result in injury or
cause the cassette to break down.
Do not block off the ventilation opening.
Doing so may result in fire or cause the machine to
break down.
•
•
iv SR-2000αUser’s Manual (No. 0000A)

SAFETY PRECAUTIONS
Do not press the touch panel with an edged
thing.
Doing so may scratch the panel and cause the
machine to break down.
Do not install any other application.
Doing so may cause the machine to break down.
Use a soft cloth or the neutral detergent when
cleaning this machine. Do not use thinner,
benzene, etc.
Doing so may deform the machine or cause it to
break down.
•
•
•
SR-2000αUser’s Manual (No. 0000A) v

CONTENTS
CONTENTS
Chapter 1 BEFORE USING THE MACHINE........................................... 1-1
1.1 PART NAMES AND FUNCTIONS............................................................................ 1-2
Front View........................................................................................................................... 1-2
Rear View ........................................................................................................................... 1-2
Keypad................................................................................................................................ 1-3
1.2 MACHINE INSTALLATION ...................................................................................... 1-4
Precautions for Installation.................................................................................................. 1-4
Level Adjustment................................................................................................................. 1-5
1.3 LABEL ROLL INSTALLATION ................................................................................ 1-6
1.4 PAPER ROLL INSTALLATION ................................................................................ 1-8
1.5 CLEANING ............................................................................................................. 1-10
Cautions for Using Cleaning Fluid......................................................................................1-10
Air Intake Filter Cleaning....................................................................................................1-11
Operation Panel and Main Body Cleaning .........................................................................1-12
Chapter 2 OPERATION MODE ............................................................... 2-1
2.1 OPERATION FLOW ................................................................................................. 2-2
2.2 BASIC SCREENS .................................................................................................... 2-3
Initial Screen ....................................................................................................................... 2-3
PLU Select Screen.............................................................................................................. 2-4
Weighing Product Screen ................................................................................................... 2-4
Fixed Price Product Screen ................................................................................................ 2-4
2.3 WEIGHING PRODUCT SALES ............................................................................... 2-5
2.4 FIXED PRICE PRODUCT SALES ........................................................................... 2-7
2.5 TARE WEIGHT SUBTRACTION.............................................................................. 2-9
Actual Tare Weight ..............................................................................................................2-9
Input Tare Weight................................................................................................................ 2-9
Preset Tare Keys................................................................................................................2-10
2.6 DISCOUNT OPERATIONS......................................................................................2-11
Amount Discount................................................................................................................2-11
Percent Discount................................................................................................................2-11
Special Price ......................................................................................................................2-11
2.7 TEMPORARY DATA CHANGE .............................................................................. 2-12
Unit Price Change..............................................................................................................2-12
Weighing Product Change to Fixed Price Product .............................................................2-12
Fixed Price Product Change to Weighing Product .............................................................2-13
Date Change......................................................................................................................2-13
2.8 POP MESSAGE PRINT.......................................................................................... 2-15
Unit Price Change..............................................................................................................2-15
2.9 VOID LAST TRANSACTION ................................................................................. 2-16
2.10 DAILY TOTAL DISPLAY......................................................................................... 2-17
2.11 AUTOMATIC / ADVANCED LABELING ................................................................ 2-18
Automatic Labeling for Weighing Products ........................................................................2-18
Automatic Labeling for Fixed Price Products .....................................................................2-19
Advanced Labeling for Fixed Price Products .....................................................................2-20
vi SR-2000αUser’s Manual (No. 0000A)

SAFETY PRECAUTIONS
Chapter 3 TOTAL ADJUSTMENT MODE ............................................... 3-1
3.1 NUMBER ADD.......................................................................................................... 3-2
3.2 WEIGHING ADD....................................................................................................... 3-5
3.3 NUMBER SUBTRACT ............................................................................................. 3-7
3.4 WEIGHING SUBTRACT ........................................................................................ 3-10
Chapter 4 TOTAL MODE ........................................................................ 4-1
4.1 DAILY TOTAL ........................................................................................................... 4-2
Total Production .................................................................................................................. 4-3
Sales Per Department......................................................................................................... 4-4
Sales Per Group .................................................................................................................4-5
Sales By PLU...................................................................................................................... 4-6
Gross Profit By PLU............................................................................................................ 4-7
Markdown Item ...................................................................................................................4-8
Designated PLU..................................................................................................................4-9
PLU Analysis......................................................................................................................4-10
Hourly Analysis ..................................................................................................................4-13
Sales per Sell Impossible PLU...........................................................................................4-15
Sales per Expired PLU.......................................................................................................4-16
Sales per Discard PLU.......................................................................................................4-17
Sales per Rewrap PLU ......................................................................................................4-18
4.2 WEEKLY TOTAL .................................................................................................... 4-19
Sales per Day ....................................................................................................................4-20
Hourly Analysis ..................................................................................................................4-21
4.3 CUMULATIVE TOTAL ............................................................................................ 4-23
Various Totals.....................................................................................................................4-24
4.4 31 DAYS TOTAL..................................................................................................... 4-26
4.5 NON-MOVEMENT PLU.......................................................................................... 4-28
4.6 PRESET REPORT.................................................................................................. 4-30
4.7 TOTAL CLEAR ....................................................................................................... 4-31
Chapter 5 PROGRAMING MODE ........................................................... 5-1
5.1 PLU DATA REGISTRATION .................................................................................... 5-2
Starting PLU Data Registration ........................................................................................... 5-2
PLU Data Registration 1/3 .................................................................................................. 5-4
PLU Data Registration 2/3 .................................................................................................. 5-8
PLU Data Registration 3/3 .................................................................................................5-10
Finishing PLU Data Registration ........................................................................................5-12
5.2 PLU PRICE CHANGE ............................................................................................ 5-13
5.3 PLU NAME REGISTRATION ................................................................................. 5-15
5.4 CAMPAIGN MESSAGE REGISTRATION ............................................................. 5-16
5.5 STORE NAME AND ADDRESS REGISTRATION................................................. 5-20
Store Name ........................................................................................................................5-20
Store Address.....................................................................................................................5-22
Print Selection of Store Name/Address..............................................................................5-23
5.6 DATE/TIME REGISTRATION................................................................................. 5-24
SR-2000αUser’s Manual (No. 0000A) vii

CONTENTS
viii SR-2000αUser’s Manual (No. 0000A)
5.7 PRESET KEYS REGISTRATION........................................................................... 5-25
PLU Preset Key Registration .............................................................................................5-25
PLU Name Edit ..................................................................................................................5-28
Key Color Change..............................................................................................................5-30
Key Layout Change ...........................................................................................................5-32
Function Key Registration..................................................................................................5-35
Page Copy .........................................................................................................................5-38
Page Delete .......................................................................................................................5-40
5.8 ADVERTISEMENT MESSAGE .............................................................................. 5-42
Message Table Allocation...................................................................................................5-42
Message Edit .....................................................................................................................5-45
Message Deletion ..............................................................................................................5-47
5.9 OPERATOR NAME REGISTRATION .................................................................... 5-49
5.10 NUTRITION REGISTRATION ................................................................................ 5-51
5.11 EXTRA MESSAGE 1 - 3......................................................................................... 5-53
5.12 COUPON MESSAGE ............................................................................................. 5-55
5.13 FREE MESSAGE 1 - 5 ........................................................................................... 5-57
5.14 DEPARTMENT NAME REGISTRATION ............................................................... 5-59
5.15 GROUP NAME REGISTRATION ........................................................................... 5-61
5.16 POP MESSAGE ..................................................................................................... 5-63
5.17 CHECK LABEL ...................................................................................................... 5-65
APPENDIX TEXT EDITING ............................................................................................A-1
Single Function Buttons ...................................................................................................... A-1
Multiple Function Buttons.................................................................................................... A-2

Chapter 1 BEFORE USING THE MACHINE
Chapter 1
BEFORE USING THE MACHINE
SR-2000αUser’s Manual (No. 0000A) 1-1

Chapter 1 BEFORE USING THE MACHINE
1.1 PART NAMES AND FUNCTIONS
This section explains the name of each part and the function of this machine.
As this manual uses the following names to give further explanation, remember the part names described
here, and read the following pages.
Front View
Rear View
1-2 SR-2000αUser’s Manual (No. 0000A)

Chapter 1 BEFORE USING THE MACHINE
Keypad
Used to change a unit price. Also used to change a fixed price
product to a unit price product.
Used to change a fixed price. Also used to change a unit price
product to a fixed price product.
Used to subtract a tare weight.
Used to issue a label.
Used to multiply a unit price of the fixed price product.
Used to call a registered product data.
Used to delete an entered numerical value. Also used to
release an error condition.
SR-2000αUser’s Manual (No. 0000A) 1-3

Chapter 1 BEFORE USING THE MACHINE
1.2 MACHINE INSTALLATION
Precautions for Installation
Install the machine horizontally to use.
Accurate measurements cannot be performed if it is
not installed horizontally.
Do not connect the machine power input with
an AC power supply exceeding the rated voltage.
Doing so may cause the machine to break down
and/or may result in danger such as electric shock.
Connect the grounding wire to protect against
electric shock.
Make sure to connect the attached grounding wire to
the grounding terminal.
•
•
•
Do not install the machine near a TV set or radio.
Doing so may cause static to the TV set and/or radio
as this machine emits week electric wave.
Do not use this machine in location that receives
direct sunlight for a long time.
Doing so may cause the machine to break down.
•
•
1-4 SR-2000αUser’s Manual (No. 0000A)

Chapter 1 BEFORE USING THE MACHINE
Level Adjustment
Be sure to turn off the power switch before placing the machine on a stable platform, and adjust the
machine inclination by turning the four level adjusters so that the level bubble is located at the center of the
window.
SR-2000αUser’s Manual (No. 0000A) 1-5

Chapter 1 BEFORE USING THE MACHINE
1.3 LABEL ROLL INSTALLATION
1. Raise the Thermal Head Cover,
and pull the Cassette to draw out of
the main body.
Confirm that the label
roll can turn gently with
the space from 0.5 to
2mm between the roll
and the Roll Stopper.
2. Load a new label roll around the
Roll Holder and raise the Roll
Stopper to fix the roll position.
For smoother passing,
fold the paper end a
little.
3. Pass the roll paper 1through 5as
shown in the figure.
4. Fix the paper end with the backing
paper stopper, and gently turn the
Winding Bobbin counterclockwise
until the label becomes tight.
1-6 SR-2000αUser’s Manual (No. 0000A)

Chapter 1 BEFORE USING THE MACHINE
5. Slide the Label Guide to fit the
paper width.
Push the Cassette
slowly so as not to get
your fingers caught
between the Cassette
and the main body.
6. Push the Cassette straight into the
main body to return to its original
position, and lower the Thermal
Head Cover.
Confirm that the
backing paper is wound
up smoothly.
If the backing paper is
wound up diagonally,
reconfirm on the label
passing, label stop
position with the
Backing Paper Stopper,
and the Label Guide
width.
7. Touch [FEED] on the screen to
issue a label.
At this time, confirm that the label is
completely peeled off.
SR-2000αUser’s Manual (No. 0000A) 1-7

Chapter 1 BEFORE USING THE MACHINE
1.4 PAPER ROLL INSTALLATION
1. Raise the Thermal Head Cover,
and pull the Cassette to draw out of
the main body.
Confirm that the paper
roll can turn gently with
the space from 0.5 to
2mm between the roll
and the Roll Stopper.
2. Load a new paper roll around the
Roll Holder and raise the roll
stopper to fix the roll position.
3. Pass the paper end 1through 3
as shown in the figure.
4. Slide the label guide to fit the paper
width.
1-8 SR-2000αUser’s Manual (No. 0000A)

Chapter 1 BEFORE USING THE MACHINE
Push the Cassette
slowly so as not to get
your fingers caught
between the Cassette
and the main body.
5. Push the Cassette straight into the
main body to return to its original
position, and lower the Thermal
Head Cover.
6. Cut the paper that comes out of the
outlet.
SR-2000αUser’s Manual (No. 0000A) 1-9

Chapter 1 BEFORE USING THE MACHINE
1.5 CLEANING
Cautions for Using Cleaning Fluid
Use a soft cloth and a neutral detergent to clean the machine.
Do not use thinner, benzene, etc. Doing so may damage the original safety functions.
For some parts, use cleaning fluid (isopropyl alcohol).
Read the cautions below before using the cleaning fluid.
 Do not use cleaning fluid near fire as the fluid is flammable.
 Do not use cleaning fluid in a poorly ventilated area. Always provide adequate
ventilation when cleaning.
Take the following actions in the event of an accident:




If the fluid gets in your eye
 Immediately wash your eye(s) with water for at least 15 minutes, and consult your doctor.
 If you wear contact lenses, remove and wash them.
If the fluid comes into contact with your skin
 Immediately rinse the area of contact with water, and then wash with soap.
 If you notice any skin abnormalities at the area of contact, or if any pain persists, consult
your doctor.
If the fumes of the fluid are inhaled
 Immediately move the victim to an area where fresh air is available, and have the victim lie
down and keep warm.
 If breathing becomes difficult or stops, provide artificial respiration and seek medical
attention immediately.
If the fluid is swallowed
 Do not try to induce vomiting.
 Do not give the victim anything to drink, and do not rinse the mouth.
 If vomiting occurs naturally, have the victim lean forward to reduce risk of aspiration.
 Keep the victim warm and seek medical attention.
1-10 SR-2000αUser’s Manual (No. 0000A)