ISHIDA Uni-5 User manual

User’s Manual
Ver. 1.02
IMPORTANT
•Read this manual thoroughly, and do not perform installation,
operation, maintenance, or inspection unless you fully
understand all of the contents.
•Keep this manual in a safe place where you can refer to it
easily while installing, operating, and carrying out
maintenance or inspections.
RS-61004-11 1.02

© ISHIDA Co., Ltd. 2008 All rights are reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means
mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA.

Chapter 12 ADJUSTMENT MODE
ADJUSTMENT MODE
12.1 ADJUSTMENT MODE ENTRY
1. Make sure that the initial screen is displayed.
2. Press the [MODE] key on the key sheet.
The Operation Mode screen appears. Then, press the [ADJUST] button on the screen
3. The Adjustment Menu Select screen appears.
12
UNI-5 User’s Manual 12-1

Chapter 12 ADJUSTMENT MODE
12.2 DATE / TIME ADJUSTMENT
1. Press the “TIME / DATE SET” field on the Adjustment Menu Select screen.
2. The Time/Date Set screen appears.
3. To change the date, enter a new date and press the “DATE” field.
EXAMPLE 22 June, 2007
12-2 UNI-5 User’s Manual

Chapter 12 ADJUSTMENT MODE
4. To change the time, enter a new time and press the “TIME” field.
EXAMPLE 13:50:00
5. To register new date and time, press the [SET] button.
6. The confirmation screen appears. Then, press the [EXEC] button for execution.
UNI-5 User’s Manual 12-3

Chapter 12 ADJUSTMENT MODE
12.3 TOUCH PANEL ADJUSTMENT
1. Press the “TOUCH PANEL” field on the Adjustment Menu Select screen.
2. The Touch Panel screen appears.
3.
Press the [+] button on the upper left of the screen.
4. Press the [+] button on the lower right of the screen.
12-4 UNI-5 User’s Manual

Chapter 12 ADJUSTMENT MODE
5. Press the [SET] button to confirm calibration.
UNI-5 User’s Manual 12-5

Chapter 12 ADJUSTMENT MODE
12.4 DISPLAY CHECK
1. Press the “DISPLAY CHECK” field on theAdjustment Menu Select screen.
2. The Display Check (Vertical) screen appears.
Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer
displays.
3. Press the [HORIZONTAL] button to change to the horizontal display check screen.
4. The Display Check (Horizontal) screen appears.
Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer
displays.
12-6 UNI-5 User’s Manual

Chapter 1 BEFORE USE
BEFORE USE
1.1 SPECIFICATIONS
Items Descriptions
Use conditions Temperature: 5 to 35°C
Humidity: 30 to 85%, Non condensing.
Power supply: AC100 – 240V, 50 / 60Hz
Power consumption 1.0A/0.5A
Weight Bench type: Approx.11.5 kg
Pole type: Approx.12.5 kg
Weighing capacity 15 kg: 0 to 6/0.002 kg, 6 to 15/0.005 kg
Weighting accuracy 1/3000
Operator/Customer display 7.0 inch color, monochrome liquid crystal with back light, 480 X
234dots
Printing method Direct thermal method
Thermal head 2 inches (448dots) and 8 dots/mm
Printing speed 100mm/second, 120mm/second
Note: The printing speed may vary according to label conditions.
Printing effective size 56mm
Label size Label width: 30mm to 60mm
Label length: 20mm to 150mm
Number of label cassettes 7 cassettes
Input/Output LAN 1 channel
USB 1 channel
CF 1 channel
Drawer 2 channels
Program store medium Flash ROM (32M bytes)
1
UNI-5 User’s Manual 1-1

Chapter 1 BEFORE USE
1.2 MODEL VARIATIONS
Bench Type
Pole Type Elevated Type
Self-service Type
1-2 UNI-5 User’s Manual