J D Williams 023 9433 Series User manual

Assembly Instructions - Please keep for future reference
Width - 47.2cm
2 Drawer Filing Cabinet
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 38.8cm
Height - 56.1cm
Rev A- 22/05/19
023 xx 9433
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Top (47.2x38.8cm)
1390
Left End Panel
(54.6x35.5m)
1391
Plinth (43.8x6.0cm)
1394
Right End Panel
(54.6x35.5 cm)
1392
Backpanel (48.7x44.8cm)1397
Drawer Front
(46.4x15.7cm)
1396
Drawer Bottom
(40.1x29.8cm)
8079
Left drawer side (30.0x10.0cm)
Drawer back (39.0x10.0cm)
Right drawer side (30.0x10.0cm)
622xx7002
624xx7008
623xx7002
Drawer Bottom
(40.1x32.6cm)
7622
Drawer Front
(46.4x32.0cm)
1395
Left drawer side (33.0x25.0cm)
622xx7004
Right drawer side (33.0x25.0cm)
623xx7004
Drawer back (39.0x25.0cm)
624xx7009
Bottom (43.8x35.5cm)
1393

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 8
Code 760001103
Metal dowel x 14
Code 760003004
ABC
E
DF
I
Small cam x 6
Code 760003005
8mm screw x 8
Code 700003510
Panel pin x 5
Code 760001012
Panel pin guide x 1
Code 684004501
G
18mm bolt x 4
Code 700002021
H
N
Handle x 2
Code 643003506
Panel Holder x 3
Code 680003505
Left Bracket x 2
Code 760xx7000
Right Bracket x 2
Code 760xx7000
Right Runner x 2
Code 760xx7002
Left Runner x 2
Code 760xx7000
L1 R1
R2
L2
12mm screw x 16
Code 690001008
O
Wooden dowel x 4
Code 770001006
P
Filing Trim x 2
Code 680071872

Exploded View
4
1397
1393
1392
1390
1391
1394
622xx7002 624xx7008
623xx7002
1395
1396
8079
7622
623xx7004
622xx7004 624xx7009

Step 1
Assembly Instructions
5
B
x4
B
O
x4
Fitting dowels to top
panel.
Step 2
B
A
B
x4
B
B
1390
B
B
Step 3
A
A
Fitting wooden dowels
to the plinth panels.
Fitting cams and
dowels to the end
panels.
Insert 4 metal dowels
into the top panel 1390
B
a: Insert 2 metal cams
and 2 metal dowels
into left end panel
.
1391
O
Insert 4 wooden dowels
into the plinth panel
Note: Tighten metal
dowels up fully against
the panel.
Do not over-tighten.
1394
1392
A
B
A
x4
A
B
b: Insert 2 metal cams
and 2 metal dowels
into right end panel
.
1392
A
B
B
O
O
O
O
1394
B
B
A
A
1391

Assembly Instructions
6
Step 4
x2
E
E
N
x4
N
x2
Attaching the left
bracket to the left end.
Using 2 screws ,
secure the bracket to
the left end panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
Repeat on all brackets.
E
Corresponding
Hole
1ST
Diagram 1
Diagram 2
L1
L1
L1
L1
1391
Step 5
E
N
Attaching the right
bracket to the right end.
Using 2 screws ,
secure the bracket to
the right end panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
Repeat on all brackets.
R1
1392
x2
E
x4
N
x2
R1
1391
E
Step 6
Inserting cams into the
bottom panel.
Insert 4 cams into the
bottom panel .
A
A
A
A
1393
1393
A
A
x4
E
E
E
E
N
1392
2ND
1ST
Diagram 1
Diagram 2
E
E
N
R1
R1
E
E
E
E

a: Insert dowels into
drawer front .
Note: Insert metal
dowels as far as
shown by arrows.
Repeat on
Do not over tighten.
7
Drawer assembly
B
B
C
Step 7
c: Insert wooden dowels
in drawer back
into holes in
left
right hand
drawer sides.
Repeat the following steps
on drawer sections,
and
B
b: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.
C
C
B
B
C
C
a:
b:
c:
Right hand side
Left hand side Drawer Back
Continued on next page.
1396
1396
624xx7008
622xx7002
623xx7002
622xx7002
623xx7002
623xx7002
624xx7008
622xx7002
Assembly Instructions
x2
x6
I
G
x2
x4 x2 x2
N
x12
L2
R2
Right hand side
623xx7002
Left hand side
622xx7002
622xx7004 623xx7004
624xx7009
1395

e:Insert cams already
inserted in left and right
drawer sides onto
dowels in drawer
front .
8
Drawer assembly
Continued...
C
Assembly Instructions
Step 7- Continued
d: Slide drawer bottom
into grooves in
left,right drawer sides
and drawer back.
Ensure foil on the
drawer bottom is facing
upwards.
B
Turn cam 180 degrees
to lock
f: Secure handle to
drawer front
using bolts
C
G
G
d:
e:
f:
8079
8079
1396
1396
1396
FOIL FACE
g: Using 12 screws
secure the left runner
and the right runner
to the drawer box.
Ensure that the wheel on
the runners is to the
back of the drawer box.
Repeat steps with other
drawer.
N
N
N
N
g:
L2
L2
R2L2
R2
I
I
Turn Drawer upside
down.
1396
G

Assembly Instructions
9
Step 8
Step 9
Connect the dowels in
the left end to the
cams in the bottom panel
and the wooden
dowels in the plinth panel
.
Turn cams 180 degrees
to lock.
Connect left end to
the bottom and plinth
panel
1391
1394
Connect the dowels in
the right end to the
cams in the bottom panel
and the wooden
dowels in the plinth .
Connect right end to
the bottom and
plinth panel
1392
1394
Step 10
Ensure plinth is
not overhanging.
Ensure plinth sits
flush.
Connect the dowels in
the top panel to
the left end and
right end .
Connect the top panel.
1390
1391
1392
1391
1392
1391
1390
1394
1393
1393
1394
1393
1393
1392

Assembly Instructions
10
Step 12
Step 11
DIAG 1 DIAG 2 DIAG 3
XX
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY
Measure to
external corners
Slide back panel into
grooves and Squaring
up the unit.
IMPORTANT!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
Ensure a tape
measure is used
to square unit up.
XX
YY
YY
D
F
D
x4
F
x1
Secure back panel
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
Slide the back panel into
the grooves in the end
panels and top panel.
XX
1397
1393

Assembly Instructions
11
x3
Step 13
Add stability blocks.
Slide the thin point of the
stability blocks
between the back panel
and the grooves.
Once inserted fully,
tighten the screws in the
stability blocks.
1397
H
H
H
H
H
Step 14
Fit the drawers and
filing trims.
Stand the unit up.
Tilt the drawers as
shown and slide onto the
runner brackets.
Place the filing trims
onto drawer sections
and
.
H
1397
x2
P
622xx7004
623xx7004
P
P
P
622xx7004
623xx7004
IMPORTANT!
Please ensure that the
stability blocks are used
correctly to secure the
back panel in place.

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)