J D Williams 2 Drawer Entertainment Center 033 7162... User manual

Assembly Instructions - Please keep for future reference
Width - 97.6cm
2 Drawer Entertainment Center
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534 123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 38.8cm
Height - 49.6cm
033 xx 7162
MADE IN
GREAT BRITAIN
Rev C - 12/01/2017

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Left End Panel
(32.4x36.8cm)
0534
Right End Panel
(32.4x36.8cm)
0535
Divider Panel
(32.4x36.8cm)
0536
Backpanel x 2
(46.3x15.8cm)
0541
Lh Draw Front
(48.2x15.7cm)
0539
Rh Draw Front
(48.2x15.7cm)
0540
Top (97.6x38.8cm)
0532
Lh Shelf Panel
(46.3x36.7cm)
0537
Rh Shelf Panel
(46.3x36.7cm)
0538
Bottom (97.6x38.8cm)
0533
Left drawer side x 2
(30.0x10.0cm)
Drawer back x 2
(41.4x10.0cm)
Right drawer side x 2
(30.0x10.0cm)
622xx7002
624xx7005
623xx7002
Drawer Bottom x 2
(42.6x29.8cm)
4472

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534 123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 14
Code 760001103
Metal dowel x 18
Code 760003004
ABC
E
DF
I
Small cam x 4
Code 760003005
8mm screw x 8
Code 700003510
GH
Left Bracket x 2
Code 760xx7000
Right Bracket x 2
Code 760xx7000
Right Runner x 2
Code 760xx7000
Left Runner x 2
Code 760xx7000
KN
Wooden dowel x 6
Code 770001006
L1 R1
R2
L2
12mm screw x 32
Code 690001008
Leg x 4
Code 721077160
Handle x 2
Code 640073515
20mm bolt x 2
Code 700002006
2” Woodscrew x 6
Code 690004529
Leg Bracket x 4
Code 760007160
J
Panel Holder x 4
Code 680003505

Exploded View
4
0532
0537
0536
0538
0535
0533
0522
0541
0534
0541
4472
4472
622xx7002
624xx7005
623xx7002
622xx7002
623xx7002
624xx7005
0540
0539

0532
G
G
Step 1
Assembly Instructions
5
B
x6
B
Fitting dowels to top
panel.
B
B
x4
B
B
B
B
B
B
Step 2
Fitting cams, metal and
wooden dowels to the
end panels.
Insert 6 metal dowels
into the top panel 0532
Note: Tighten metal
dowels up fully against
the panel.
Do not over-tighten.
A
B
A
x4
G
G
x4
A: Insert 2 metal cams
2 wooden dowels ,
and 2 metal dowels
into right end panel
0535
A
A
A
A
A
0535
0534
G
G
A
B
B
B
B
B
G
B: Insert 2 metal cams
2 wooden dowels ,
and 2 metal dowels
into left end panel 0534
A
B

0534
Assembly Instructions
6
Step 3
B
x1
E
E
N
x2
N
x1
Attaching the left
bracket to the left end.
Using 2 screws ,
secure the bracket to
the left end panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
E
E
L1
L1
0534
Step 4
E
N
Attaching the right
bracket to the right end.
Using 2 screws ,
secure the bracket to
the right end panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
R1
0535
x1
E
x2
N
x1
R1
0535
E
Diagram 1
Diagram 2
L1
Diagram 1
Diagram 2
N
N
R1
E
1ST
L1
R1
1ST
Insert 2nd screw into
corresponding hole
Insert 2nd screw into
corresponding hole

Step 5
Assembly Instructions
7
B
x2
Fitting cams, metal and
wooden dowels to the
divider panel.
A
x2
G
G
x2
A: Insert 2 metal cams
2 wooden dowels
and 2 metal dowels
into divider panel 0536
A
A
A
0536
G
G
B
B
B
E
Step 6
E
N
Attaching the right
bracket to the divider.
Using 2 screws ,
secure the bracket to
the divider panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
R1
0536
x1
E
x2
N
x1
R1
0536
E
Turn the divider over
Diagram 1
Diagram 2
N
R1
R1
1ST
Insert 2nd screw into
corresponding hole

Assembly Instructions
8
Step 7
Step 8
0536
B
x1
E
E
N
x2
N
x1
Attaching the left
bracket to the divider.
Using 2 screws ,
secure the bracket to
the divider panel
as shown in diagram 1.
Use 1 screw to
secure the front of the
bracket.
E
E
L1
L1
0536
0536
B
B
x2
Fitting metal dowels
to the divider panel.
Insert 2 metal dowels
into divider panel 0536
B
B
B
Important:
We recommend you
do this on the packaging
the unit came in to
protect your floor.
Diagram 1
Diagram 2
L1
N
E
1ST
L1
Insert 2nd screw into
corresponding hole

0537
Assembly Instructions
9
Step 9
A
A
A
A
A
A
A
A
A
x8
Fitting cams to the
shelf panels.
A: Insert 4 metal cams
into shelf panels
& .
0537
0538
A
0538

Assembly Instructions
10
Step 10
Fitting dowels to the
drawer fronts.
B
Insert 2 metal dowels
into the the drawer
fronts . Repeat on
.
0539
0540
x4
B
x4
C
Step 11
H
x2
I
x2
B
C
A
B
Left hand side
Right hand side
622xx7002
623xx7002
622xx7002
623xx7002
C
C
B: Insert wooden dowels
in drawer back
into holes in
left
right hand
drawer sides.
Right hand side
Left hand side Drawer Back
624xx7005
622xx7002
623xx7002
623xx7002
624xx7005
622xx7002
0539
B
0539
4472
Foil surface facing upwards.
Plain chipboard surface
to underside.
C: Sit drawer bottom
into groove on
drawer front .
Ensure foil on the
drawer bottom is facing
upwards.
0539
4472
A: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.

Assembly Instructions
D
E
D:Locate the metal
dowels (already inserted)
in the drawer front into the
small cams in the left and
right hand drawer sides.
Ensure drawer sides are
pressed against drawer
front.
Turn the cam 180 degrees
to lock.
E:
Fit bolt through
the pre-drilled holes in
the drawer front
and connect to the handle
.
H
I
0539
Using 6 screws
secure the left runner
and the right runner
to the drawer box.
Ensure that the wheel on
the runners is to the
back of the drawer box.
11
N
N
L2
L2
R2
R2
x12 x2
Step 12 x2
Turn drawer upside
down
H
I
0539
N
N
N
L2
L2
R2
H
0539
Repeat on .
0540
Repeat on .
0540

Assembly Instructions
12
Step 13
Connect the dowels in
the left hand end panel
to the cams in the
shelf panel.
Turn cams 180 degrees
clockwise to lock.
Connect the left end
and divider to shelf.
0534
0537
Step 14
0534
0537
0536
0536
Connect the dowels in
the divider panel
to the cams in the
shelf panel.
0536
0537
Connect the dowels in
the right hand end panel
to the cams in the
shelf panel.
Turn cams 180 degrees
clockwise to lock.
Connect the right end
and divider to shelf.
0535
0538
Connect the dowels in
the divider panel
to the cams in the
shelf panel.
0536
0538
0538
0535
Groove to this side
Groove to this side

Assembly Instructions
13
Step 16
Step 15
x6
F
Fit the backpanels
into shelves and bottom
grooves. Secure
bottom panel
Slot backpanels
into grooves on shelf
panels &
Lower bottom panel
onto dowels in ends and
divider panels ensuring
backpanels slot into
groove.
0541
0537 0538
0533
Connect the dowels in
the top panel to the
cams in the left ,right
and divider panels
& .
Turn cams 180 degrees
clockwise to lock.
Connect the top panel
to the left, right and
divider panels.
0532
0535
0534
0536
0534
0532
0535
Overhang
Overhang
Lay the unit on its top.
2 people may be
required.
Groove to this side
0536
0541
0534
0536
0535
0541
0533
0537
0538
2 people may be
required.
F
F
F
F
F
F
Using 6 screws attach
the bottom panel to
the left end panel
right end panel
and divider panel .
0533
0534
0535
0536
F

0533
Assembly Instructions
14
Step 17
x4
N
x16
K
Attach leg bracket
to the bottom panel.
Attach the leg bracket
to the bottom panel
with 4 screws .
0533
N
K
K
N N
N N
N
N
N
N
IMPORTANT :
Please ensure the
brackets are attached
as shown (Dia. 1).
Front of unit
Leg Bracket Leg Bracket
Dia.1
N N
N N
K
N N
N N
K
N N
N N
K
K
Step 18
Secure the legs to the
leg bracket.
Screw legs into brackets
until tight.
x4
D
D
K
D
D
D
K
K
K
K
D
Lay the unit on its front
2 people reccomended.

Assembly Instructions
15
Step 19
Step 20
DIAG 1 DIAG 2 DIAG 3
XX
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY
Measure to
external corners
Squaring up the unit.
IMPORTANT!
Ensure a tape
measure is used
to square unit up. XX
XX
YY
YY
x4
Add stability blocks.
Slide the thin point of the
stability blocks
between the back panel
and the grooves in the
bottom and shelf panels.
Once inserted fully,
tighten the screws in the
stability blocks.
J
J
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
J
J
J
J
Stand the unit upright
2 people reccomended.
J

Assembly Instructions
16
Step 21
Fit the drawers.
Tilt the drawer as
shown and slide onto the
runner brackets.
0539
0540

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534 123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)