J D Williams Norton Shoe Rack User manual

Assembly Instructions - Please keep for future reference
Width - 66.4cm
Shoe Storage Cabinet
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534 123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 24cm
Height - 87cm
Rev B - 20/03/2017
045 xx 5525

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 4.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Left hand end (87x24.2cm)
Code - 9808
Right hand end (87x24.2cm)
Code - 9809
Large shoe rail x 4 (62.2x14.1cm)
8320
Code -
Shoe flap x 2 (63x38.6cm)
Code - 0709
Top (63.4x24cm)
8315
Code -
Backpanel (66x30cm)
8322
Code -
8321
Code -
Small shoe rail x 2 (62.2x8.8cm)
8316
Code -
Plinth (63.4x92cm)
8379
Code - .
Not required in build of unit.
Packing Panel (63.4x103cm)

3
Components -Exploded View
Important - Thick lines indicate finished edges
8322
9809
8315
9808
8320
8320
8320
8320
8316
8321
8321
0709
0709

70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components-Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534 123 Please turn to back page
for important information when contacting Customer Helpline.
4
Cross headed screwdriver
( large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
12mm screw x 12- Code 690001008
D
J
13mm screw x 16 - Code 700006002
H
R
L bracket x 1
Code 760001901
Q
12mm screw x 2 - Code 690001099
L
45mm screw x 8 - Code 690001075
G
Panel pin x 10 - Code 760001012
E
Shelf Stop Pin x 4 - Code 680362000 Shelf Pivot x 4- Code 680362000 Pivot x 4 - Code 680362000
Left Hand Bracket x 2
Code 680362000
T
S
UVW
Right Hand Bracket x 2
Code 680362000
2 Pair of Fittings
Cover cap x 8
X
Panel pin guide x 1
Code 684004501
F
Important: Fittings S to W are supplied fastened together.
Handle x 2
Code 643005527
20mm bolt x 4
Code 700002006

Assembly Instructions
5
Fittings you will need for this step:
U
(x4)
Fitting pivot & shelf pin
to left & right end
panels
W
(x4)
9808
9809
U
W
W
W
W
U
U
U
Note: Use a hammer
to knock in pivots
and shelf pins into
holes.
U
W
Step 2
Step 1
Seperate all
components and ensure
all plastic sprue is
removed from fittings
STVW
U
STVW
U

Step 3
Assembly Instructions
6
Fittings you will need for this step:
Attach plinth &
top panel to right hand
end panel.
L
(x4)
9809
8315
8316
L
L
L
Locate screw
through hole in rh end
panel and screw
into hole in plinth .
8316
9809
L
Locate screw through
holes in rh end
panel and screw
into holes in top .
9809
8315
L
Foil Face
Raw Face
L
Step 4
9808 8315
L
L
L
L
8316
Fittings you will need for this step:
L
(x4)
Attach left hand end
panel to plinth &
top panel.
Locate screw
through hole in lh end
panel and screw
into hole in plinth .
8316
9808
L
Locate screw through
holes in lh end
panel and screw
into holes in top .
9808
8315
L

7
Step 5
Assembly Instructions
Square unit up
Attach backpanel to
ends and top
DIAG 1
DIAG 2
DIAG 3
XX
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY
Ensure a tape measure
is used to square up
unit!
Important:
Fittings you will need for this step:
(x1)
E
F
(x10)
E
F
Align backpanel
so that there is an equal
gap from the edge of
end panels and
.
Then secure using panels
pins .
Use the panel pin guide
when locating the
panel pins . This will
hold the panel pins
vertical and ensure the
correct distance from the
edge.
E
F
E
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
8322
9808
9809
XX
YY
YY
XX
Step 6
9808 8322
9809
9808
9809
E
8315
8315

8
Assembly Instructions
Step 7
H
(x12)
Attaching left and
right hand brackets to
flap
0709 x2
T
S
S
(x2) (x2)
Align the left hand
bracket with the
pre-drilled holes of flap
panel .Secure
using screws .
Repeat this to attach the
right hand bracket .
S
0709
H
T
8319 x2
8321
Locate the small rail
in’between the left
& right hand brackets
as shown.
HH
H
H
HH
T
8321
Fittings you will need for this step:
(x8)
D`
D
Secure the small rail
0 to left and right
hand bracket using
screws .
8321
D
D
Fittings you will need for this step:
Step 8
Attaching small and
large rail to left and
right hand brackets
8320
Repeat on remaining
flap.
Locate the large rail
in’between the left
& right hand brackets
as shown.
8320
D
Secure the large rail
0 to left and right
hand bracket using
screws .
8320
D
D
Warning.
DO NOT OVERTIGHTEN
Before commencing
ensure step 1
has been followed
fully.
Important:
Warning.
DO NOT OVERTIGHTEN

9
Step 9
Assembly Instructions
Important:
2 people
required.
Attach flap assemblies
a: Carefully stand the
unit upright.
Position the flap into the
main unit as shown.
a:
b:
b: Carefully pull the
brackets in the direction
shown by the arrows.
This will allow you to line
the curved slot in the
brackets up with shelf
stop pins already
inserted in end panels.
c: Carefully pull the
brackets in the direction
shown by the arrows.
This will lock the brackets
onto the shelf stop pins
.
U
U
U
U
c:
U
Continued on next page.
Curved slot
Warning.
Ensure fitting already
inserted in end panels
is not dislodged.
W

10
Assembly Instructions
Step 9 - Continued Fittings you will need for this step:
V
(x2)
H
(x2)
To fix the flap
assemblies to the lh end
panel and right
hand end panel
through lh and rh brackets
Firstly, using a screwdriver
insert into . As
shown in ( diag 1 ).
9808
9809
H
H
V
V
d:
H
V
Repeat step 9a - 9e
on the remaining
flap.
(x4)
D`
8320
e:
D
e: Secure the large rail
0 to left and right
hand bracket using
screws .( diag 4 )
8320
D
D
Fittings you will need for this step:
d:
9808
W
W
HV
( diag 1 )
( diag 2 )
Now,While one person
lines up the hole in the
brackets with fitting
already inserted in end
panels, the other person
inserts and secures
and . (diag 2 ).
H
V
W
H
W
9809
V
Warning.
Ensure rail is inserted fully
into slot in brackets.
See diag 1,2 and 3.
Warning.
DO NOT OVERTIGHTEN
( diag 1 ) ( diag 2 )
( diag 3 )
Position rail into slots. To ensure the rail fits
correctly into the bottom
slot, push the bracket
on the area as shown
above.
Note the rail now sits
flush up to the slot.
Slot
DO NOT OVERTIGHTEN
( diag 4 )
Warning.
DO NOT OVERTIGHTEN
Warning.

11
Assembly Instructions
Step 10 Fittings you will need for this step:
J
(x2)
G`
(x4)
Secure handles to
flap panels
using bolts .
J
G
0709
G
G
J
0709
Attach handles

12
Assembly Instructions
Step 11 Fittings you will need for this step:
(x8)
Cover exposed screw
heads using caps .
X
X

13
Assembly Instructions
Step 12 Fittings you will need for this step:
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
R
(x1)
Q
(x2)
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
Warning:
2 people to lift.
Lift with care.
With help move the
unit into position.
Warning:

14
Congratulations! Your unit is complete
Note: Please turn over for
important information.

15
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534 123
Please have the following information: Unit Description, Product Code, Product Colour,
Place of Purchase, Catalogue Ref. No., Item Code, and have the assembly instructions close
to hand.
You can also e-mail your requests to us at: [e-mail]
Simply contact us on CUSTOMER HELPLINE : 01709 534123 Between 8am - 4.30pm
Monday to Thursday and 8am - 2.30p.m friday. Your statutory rights are not affected.
Alternatively Write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
Important Information