J D Williams OSLO 3 DRAWER User manual

Assembly Instructions - Please keep for future reference
Width - 66.8cm
3 Drawer Chest
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 33.0cm
Height - 59.2cm
Rev C - 03/10/2016
002 xx 6651
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Top (66.8x33.0cm)
5516
Left End Panel
(57.7x32.8m)
0266
Plinth (63.4x7.6cm)
8553
Right End Panel
(57.7x32.8cm)
0267
Backpanel (51.0x66.0cm)9200
Draw Front x 3
(63.0x15.7cm)
0155
Drawer Bottom x 3
(61.2x29.8cm)
5671
Left drawer side x 3 (30x10cm)
Drawer back x 3 (60.1x10cm)
Right drawer side x 3 (30x10cm)
622xx7002
624xx7010
623xx7002
Bottom (63.4x32.7cm)
0268

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 12
Code 760001103
Metal dowel x 18
Code 760003004
ABC
E
DF
I
Small cam x 6
Code 760003005
8mm screw x 12
Code 700003510
Panel pin x 24
Code 760001012
Panel pin guide x 1
Code 684004501
G
20mm bolt x 3
Code 700002021
Runner x 6
Code 760001040
H
Handle x 3
Code 640003511
J
9mm bolt x 6
Code 690001078

5671
Drawers x3
Exploded View
4
8553
622xx7002
623xx7002
624xx7010
0266
5516
9200
0155
0268
0267

A
Step 1
Assembly Instructions
5
B
x4
B
A
x8
Fitting dowels to top
panel.
Step 2
B
A
B
x8
B
B
5516
B
B
Step 3
A
A
A
A
A
A
A
A
Fitting cams to the
plinth and bottom
panels.
Fitting cams and
dowels to the end
panels.
Insert 4 metal dowels
into the top panel 5516
B
a: Insert 2 metal cams
and 4 metal dowels
into left end panel
.
0266
A
Insert 4 cams into the
plinth panel .
Insert 4 cams into the
bottom panel .
Note: Tighten metal
dowels up fully against
the panel.
Do not over-tighten.
8553
B
0266
0267
A
B
A
x4
A
B
b: Insert 2 metal cams
and 4 metal dowels
into right end panel
.
0267
A
B
B
B
B
B
B
A
A
8553
A
A
0268
0268
B

Assembly Instructions
6
Step 4
H
E
H
E
Front of Runner
Back of Runner
A
B
H
x6
E
x12
Attaching runners to
the end panels.
Position the runner so
that the second hole
from the front of the
runner lines up with the
pre-drilled hole nearest
to the edge of the panel.
Use screws to secure
the runner.
Slide the runner forward
revealing the back of the
runner. The second hole
to the back of the runner
will now line up with
the second pre-drilled
hole.
E
Front of runner
0266
0267
E
E
H
E
E
H
E
E
H
E
E
H
E
E
H
E
E
H
x6
A: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole. Left hand side
Right hand side
622xx7002
623xx7002
622xx7002
623xx7002 A
C
C
C
Step 5
B: Insert wooden dowels
in drawer back
into holes in
left
right hand
drawer sides.
623xx7002
624xx7010
622xx7002
B
A
B
x6
B
Left hand side
622xx7002
Drawer Back
624xx7010
Right hand side
623xx7002

Fitting the handles
to drawer fronts.
Secure the handle with
bolt .
Repeat on the remaining
2 drawer fronts.
Assembly Instructions
7
D: Slide drawer bottom
into grooves in the left
and right drawer sides
and the drawer back.
C
E:Locate the metal
dowels (already inserted)
in the drawer front into the
small cams in the left and
right hand drawer sides.
Turn cams 180 degrees to
lock.
Repeat on all drawers.
D
E
Step 6
G
I
C: Insert 2 metal dowels
into the the drawer
fronts .
0155
x3
G
x3
I
B
B
B
0155
SLIDE!
5671
Foil surface facing upwards.
Plain chipboard surface
to underside.
622xx7002
5671
622xx7002
623xx7002
623xx7002
624xx7010
624xx7010
0155
G
I
0155

8553
Assembly Instructions
8
Step 7
Step 8
Connect the dowels in
the left end to the
cams in the plinth panel
and bottom panel
.
Turn cams 180 degrees to
lock.
Connect left end to
the plinth and bottom
panels.
0266
0268
8553
Connect the dowels in
the right end 7 to the
cams in the plinth panel
and bottom panel
.
Turn cams 180 degrees to
lock.
Connect right end to
the plinth and bottom
panels.
0267
0268
8553
Step 9
Ensure plinth is
not overhanging.
Ensure plinth sits
flush.
Connect the dowels in
the top panel to
the left end and
right end
Connect the top panel.
5516
0266
0267
0266
5516
0266
0268
0268
0267
8553
0268
0267
8553

Assembly Instructions
9
Step 11
Step 10
DIAG 1 DIAG 2 DIAG 3
XX
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY
Measure to
external corners
Squaring up the unit.
IMPORTANT!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
Ensure a tape
measure is used
to square unit up. XX
YY YY
D
F
D
x16
F
x1
Secure the back panel
to the unit.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
XX
9200
0268

Assembly Instructions
10
Step 12
Fit the drawers.
Stand the unit up.
For this step we
recommend you follow
the helpful hints on the
next page.
2nd Hole
J
x6
J

Assembly Instructions
11
Step 13
a: Pull sliding part of
drawer runners out
so they are fully
extended.
Locate drawers helpful
hints
H
b: Locate drawer onto
runners.
c: Locate screwdriver
into second threaded
hole in drawer runner .
d: Keeping screwdriver
in place push the drawer
closed.The screwdriver
will push against the end
panel and extend the
drawer runner .
e: Pull drawer out slowly
and line the hole in the
drawer side with the 2nd
threaded hole in the
runner . Now insert
bolts through the
drawer side and
into threaded hole in
runner .
J
J
f: Now insert bolts
through the drawer side
and into threaded hole in
runner .
J
l
J
J
D
EF
AB
C
2nd Hole
H
2nd Hole
J
L
L
L
L
L
L
L
L
J
J
H
H
H
H
H
H
H
H

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)