J D Williams Shelving Unit 011 9428 Series User manual

Assembly Instructions - Please keep for future reference
Width - 120.0cm
Shelving Unit
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 20.5cm
Height - 35.0cm
Rev A - 17/06/2019
011 xx 9428
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
1461
End Panel x2 (25.0x18.8cm)
1462 Shelf (110.0x19.0cm)
1463
Back Panel (120.0x35.0cm)

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some cases more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
ABC
45mm screw x 12
Code 690001075
Eye protection
(when using a
hammer)
Large Cross
Headed
Screwdriver
Small Hammer Tape Measure
12mm screw x 4
Code 690001008
Plate fitting x 2
Code 760008660

Exploded View
4
1461
1463
1463
1462

Step 1
Assembly Instructions
5
B
B
x2
Fitting plate fittings
to the back panel.
Step 2
C
Fitting plate fittings to
the back panel.
Insert 2 plate fittings
to the pre drilled holes in
the back panel
Insert 4 screws into
the plate fittings to
secure them to the back
panel
1461
1461
B
B
x4
C
1461
1461
C
C
B
BB
C
C
B
B
C

Assembly Instructions
6
Step 3
Connect the end panels
to the back panel.
Connect the end panels
to the back panel
using the screws
provided.
Step 4
Attach the shelf panel
to the back panel.
Connect the shelf panel
to the back panel
using screws
provided.
1461
1463
1461
A
AA
A
A
A
x4
1463
1463
A
A
A
A
A
1462
1461
1461
1462
A
x4
groove to the bottom
groove to the bottom

Assembly Instructions
7
Step 5
1462
Secure end panels to
shelf panel.
Secure the end panels
to the shelf panel
using screws .
1463
1462
A
A
x4
A
A
A
A
1463
1463

Assembly Instructions
8
Step 6
This unit is designed to
be fixed to a suitable
wall using the back plates
already attached.
No wall fixings are
provided as they will need
to suit the wall type.
Please ensure that the
fixings used are
appropriate to your wall
type.
We do not specify exact
location for mounting the
unit, this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
With help move the
unit into position.
Warning:
2 people required.
Lift with care.
Warning:
1000mm
Please refer to following
page on how to attach
the unit to the wall.

Assembly Instructions
9
A Guide to wall mounting
and fixings.
Make sure that the screws and wall plugs being used are suitable for supporting your unit.
Consult a qualifed tradesperson if you are unsure.
1. General purpose wall plug
3. Cavity Fixing wall plug 4. Cavity Fixing-Heavy Duty wall plug
6. Shield Anchor wall plug - Heavy loads
2. Plasterboard wall plug
5.Hammer Fixing wall plug
Generally aerated blocks
should not be used to
support heavy loads,
this case. For light loads,
general purpose wall
plugs can be used.
For use with
plasterboard
partitions
or hollow wooden
doors.
For use when
heavy loads such
as shelving, wall
cabinets and coat
racks.
For use with
heavier loads
such as TV & HiFi
speakers and
satelite dishes etc.
For use with
plasterboard
partitions
or hollow
wooden doors.
For use with walls stuck
with plasterboard. The
wall rather than the
plasterboard. Always
to the retaining wall.
Types of walls:
Important:
When drilling into walls always check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug if you are not sure.
2: Ensure you use the recommended drill bit to match the wall plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure wall plugs are inserted beyond the
thickness of the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well tted and are a tight t in the drilled hole.If plastic wall plugs are supplied with your
product:These are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for
your wall,seek professional advice. Failure of the product due to using incorrect xings is the responsibility of
the installer.

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)

Notes;