J D Williams Whitehaven Console Unit QN077 User manual

Dimensions
Width - 64cm
Depth - 24cm
Height - 90cm
Important– Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference
464/3944
Whitehaven Console Unit
Issue 1 - 01/09/15
QN077

2
Components -Panels
Please check you have all the panels listed below
Components - Fittings
Note:
may be supplied than are required.
Tools required
Phillips screwdriver
(medium & large)
M x1
L x1K x1J x1
1 x1 2 x1 3 x1 4 x1 5 x1 6 x1 7 x1
8 x1 9 x1 10 x1 11 x1 12 x2 13 x1
A x16 B x16 C x4 D x3 E x2 F x2 G x4 H x24 I x4

3

4
Assembly Instructions
Step 1
Step 2
Step 3
1. Insert 4 x Male
Camlocks A into
Shelf Front 3
and Base front 4
3. Connect Front 3 to
Shelf 4 and Connect
Front 6 to Base Panel
4. Insert 4 x Female
camlocks and tighten
with a suitable
screwdriver
Note: For further details,
please see the“using
camlocks” section at the
front of this instruction
A
B
3
4
A
B
A
B
A
B
6
7
2
AA
A
A
D
D
D
Note:For further details,
please see the“using
camlocks” section at the
front of this instruction
1. Insert 4 x Male
Camlocks into the
underside of Top Panel 1.
2. Connect Top Plinth 2
to Top panel using
3 x Screws D as shown
1. Insert 8 x Male
Camlocks into Side
panels 8 and 9.
9
A
A
A
A
8
A
A
A
A
C
C
C
C
C
C
C
C
C
C
C
C
7
4
9
B
B
B
B
Step 4
1. Connect Base Panel
7 and Shelf 4 to Right
side panel 9.
2. Insert 4 x female
camlocks and
tighten with a suitable
screwdriver
C
A
C
A
C
B
C
B
3
4
C
A
C
A
C
B
C
B
6
7
C
A
C
A
C
A
C
A
C
D
C
D
2
C
D
1
C
A
C
A
C
A
C
A
C
A
C
A
C
A
C
A
9
8
9
C
B
C
B
C
B
C
B
C
A
3
6
3
4
67
C
B
C
A
1
2
1
C
D
C
A
9
8
7
4
7
4
9
C
B
2. Insert 4 x Dowels C
into ends of Parts 3 and
C
C
34

5
Assembly Instructions
Step 5
Step 6
Step 7
2. Connect Top Panel 1
onto side panels 5 and
6 .
3. Insert 4 x Female
Camlocks B into Holes
shown in panels 5 and
6. Tighten with a
suitable Screw driver
Note: For further details,
please see the“using
camlocks” section at the
front of this instruction
1
12
12
13
9
8
12
12
1
B
B
B
B
6
5
C
B
6
5
1. Slide Back panels 12
into position along
grooves in side panels
8 and 9
1. Connect 2 x back
panels 12 together
using 1 x Joint strip 13
12
12
13
1
12
12
C
B
C
B
C
B
C
B
8
9
12
89
12
13
Note: For further details,
please see the“using
camlocks” section at the
front of this instruction
1. Connect Left Side
Panel 8 to Shelf 4
and base panel 7
2. Insert 4 x female
camlocks and
tighten with a suitable
screwdriver
8
B
B
B
B
C
B
C
B
C
B
C
B
8
7
4
84
7
C
B

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers

Assembly Instructions
Step 8
6
Step 9
K
D
J
M
L
1. Connect 1 x Handle E
to door 9 using 1 x
Screw F.
2. Connect 2 x Hinges G
to Door 9 using 4 x
Screws H , 2 screws
per hinge.
3. Connect the door to
the unit using 8 x Screw
H , 4 screws per hinge.
The unit is floor
standing, but it is
recommended that the
unit is secured to the
wall.
1. Connect 1 x wall
strap F to the
the units with 1 x
screws in position
Shown
2.Move the units into
desired position.
3. Mark the wall with a
suitable scribe the
position of the fixing
hole.
4. Drill hole and insert 1 x
wall plug D
5. Secure the straps to the
wall using 1 x screw
Note: To hide the strap
behind the unit, drill the
hole lower than the top of
the unit.
Warning:
Before driling,check
wall for hidden pipes
and cables.
K
M
L
J
Assembly complete
C
E
9
C
F
C
G
9
C
H
C
H
10
E
F
G
G
11
E
F
H
H
G
G
C
E
C
F
10
C
G
C
G
C
H
C
H
C
I
C
I
C
I
C
I
5
11
C
G
C
H
C
H
C
G
C
E
C
F
4 Insert 4 x Shelf supports
and Place Shelf 5
onto these
5. Repeat the above
for remaining door 8
11
C
I5