J D Williams Norton TV Unit TD465 User manual

Assembly Instructions - Please keep for future reference
Width - 98.4cm
2 Door Entertainment Unit
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 38.8cm
Height - 41.5cm
Rev B - 20/03/17
033 xx 5520
MADE IN
GREAT BRITAIN

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Bottom
(95.0x36.9cm)
9656
Left End
(40.0x38.6cm)
9657
Right End
(40.0x38.6cm)
9658
Left Divider
(30.7x36.9cm)
9659
Right Divider
(30.7x36.9cm)
9660
Door x 2
(31.6x24.7cm)
0706
Back x 2
(33.3x26.3cm)
9664
Top
(98.4x38.8cm)
9678
Small Shelf x 2
(23.6x36.8cm)
9663
Large Shelf
(44.5x36.8cm)
9662
Plinth
(95.0x7.6cm)
9148
If you have damaged or missing panels, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 20
Code 760001103
Metal dowel x 20
Code 760003004
ABC
E
DF
I
Panel pin x 28
Code 760001012
Panel pin guide x 1
Code 684004501
GH
JKL
Fully cranked 26mm
hinge x 4
Code 652001120
Hingeplate x 4
Code 653006000
Screw x 8
Code 690001008
Shelf Support x 8
Code 681003001
Bradawl
20mm bolt x 4
Code 700002006
Wooden dowel x 4
Code 770001006
45mm screw x 4
Code 690001075
Handle x 2
Code 643005527

Exploded View
4
9664
9664
9678
9657
9658
9659
9660
9663
9663
9662
9656
0706
0706
9148

Step 1
Assembly Instructions
5
A
x4
A
Fitting cams to the
bottom panel.
Insert 4 metal cams
into the bottom panel
.
Note: Ensure cam arrow
points towards the edge
with the hole.
9656
A
A
x4
Step 2
Fitting cams to the
plinth panel.
Insert 4 metal cams
to the plinth panel .
9148
A
A
A
A
9148
A
B
B
B
B
B
B
B
B
Step 3x8
B
Fitting dowels to the
top panel.
B
B
Insert 8 metal dowels
into the top panel
Note: Insert metal
dowels as far as
shown by arrows. Do not
over tighten.
9655
B
9655
A
A
A
A
9656

Assembly Instructions
6
Step 4
Step 5
B
B
B
B
B
B
B
B
B
H
H
H
H
A
A
A
A
Insert 4 metal dowels ,
2 hinges and 2
cams into the left end
panel .
Repeat on the right end
panel .
Attach dowels, cams
and hinges to both of
the end panels.
B
A
H
Insert 2 cams into
the right divider panel
.
Turn the panel over.
Insert 2 metal dowels
and 2 wooden dowels
into the right divider
panel .
Repeat on the left divider
panel .
Attach dowels, cams
and hinges to both of
the divider panels.
B
9657
9658
9660
9660
9659
x8
B
x4
B
A
x4
A
A
x4
x4
H
A
A
J
J
J
J
x4
Holes not used at
this stage.
9660
9657
9658
9660

Assembly Instructions
7
Step 6
Attach hinges and
handles to the doors
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
G
c: Secure hinges to
doors using screws .
G
K
d: Secure handle to
doors using bolts
Repeat on the second
door.
E
I
G
G
x4
K
x8
E
x4
I
x2
0706
I
A
B
C
D
G
G
K
K
K
K
E
E
0706
0706
0706
Bradawl
90
Correct
98
Incorrect

Assembly Instructions
8
Step 7
Step 8
Step 9
Connect the top panel
to the left end panel
and the divider panels.
Connect the dowels in the
top panel to the
dowels in the left end
panel , the left
divider panel and
the right divider panel
.
9657
9659
9660
9678
Connect the divider
panels to the large
shelf panel.
Connect the dowels in the
left divider and
right divider to the
cams in the shelf panel
.
9659
9660
9662
A
x4
Fitting cams to the
shelf panel.
Insert 4 metal cams
to the plinth panel .
9662
A
A
A
A
A
9662
9662
9659
9659
9657
9660
9660
Edged face
Turn cams 180 degrees to
lock.
9678
Edged face

Assembly Instructions
9
Step 10
Step 11
Connect the bottom
and the plinth panel to
the left end panel.
Connect the dowels in the
left end panel to
the cams in the bottom
panel and the
plinth panel .
9657
9656
9148
Connect the right end
panel to the top,
bottom and plinth
panel.
Connect the dowels in
the top panel to
the cams in the right end
panel .
Connect the dowels in
the right end panel
to the cams in the bottom
panel and the
plinth panel .
9678
9658
9658
9656
9148
9656
9656
9678
9657
9658
9148
9148

Assembly Instructions
10
Step 12
Secure the bottom
panel to the divider
panels.
Using 4 screws ,
secure the bottom panel
to the left divider
and the right
divider .
9656
9659
9660
L
9656
9659
9660
x4
L
L
L
L
L
Step 13
Measure to
external corners
Squaring up the unit.
Ensure a tape
measure is used
to square up unit!
Important:
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
DIAG 1 DIAG 2 DIAG 3
XX
XX
XX
YY
YY
XX
YY
YY
XX
XX
YY
YY
XX
XX
YY
YY

Assembly Instructions
11
Step 14
Attach the backpanel
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
D
x28
F
x1
D
F
Step 15
Insert 8 shelf supports .
Once inserted, seat the
shelves on top of the shelf
supports.
Fitting the shelf
supports.
D
D
x8
C

Assembly Instructions
12
Step 16
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
Hanging doors
b: Tighten screw shown
to lock hinges in
position.
See ‘Hinge adjustment’
page if the doors
need adjusting.
The doors can be fitted
to either side depending
on your preference.
Repeat the process on
the remaining door.
B
B
B
Ensure the underside of screw
B slides into slot on hingeplate.
Hinge correctly attached to
hingeplate.
Hinge incorrectly attached to
hingeplate.
Diagram 1
Diagram 2
Diagram 3
AB
0706

Assembly Instructions
13
Step 17
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
Hinge adjustment
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
A
B
C

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)