J D Williams Corner Desk 021 9438 Series User manual

Assembly Instructions - Please keep for future reference
Width - 99.6cm
Corner Desk
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 49.0cm
Height - 72.1cm
Rev A - 06/06/2019
021 xx 9438
MADE IN
GREAT BRITAIN
Shelf section on the left
Shelf section on the right

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Top (65x32.8cm)
1452 Bottom (61.6 x 32cm) 1453
Shelf (61.6x32cm)
1455
Divider x 2 (32x31.6cm)
1456
End Panel x 2 (69.1x32.4cm)
1454
Top (99.6x49cm)
1457
End Panel (70.6x35.4cm)
1458
Back (70.6x33.8cm)
1459

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
ABC
E
DF
Eye protection
(when using a
hammer)
Large Cross
Headed
Screwdriver
Small Hammer
25mm Screw x 1
Code 690001021
Large cam x 26
Code 760001103
Metal dowel x 26
Code 760003004
25mm bolt x 4
Code 700009438
Plastic insert x 4
Code 680009438
Glide foot x 1
Code 720076003
GH
L Bracket x 1
Code 760001901
12mm Screw x 2
Code 690001099

9096
Exploded View
4
1459
1454
1456
1457
1458
1456
1452
1455
1453
1454
LH Exploded view

Step 1
Assembly Instructions
5
Fitting dowels to the
top panel.
Step 2
B
Fitting dowels and
cams to the shelf panel.
Insert 6 metal dowels
into the top panel .
Insert 2 dowels and
4 cams into the shelf
panel .
Flip the panel over.
Insert 2 dowels into
the shelf panel .
1452
1455
Step 3
Fitting cams into the
divider panels.
Insert 4 cams into the
divider panel .
Repeat on the second
divider .
B
B
x6
B
A
A
A
B
B
B
B
B
B
B
B
A
A
Do not over tighten
1452
B
x4
A
x4
A
A
A
A
A
1455
NOWTURN PANEL OVER
B
B
1455
B
1455
1456 x2
1456
1456
A
A
x8

Assembly Instructions
6
Step 4
Fitting cams and dowels
to the end panels.
Insert 2 cams and 4
dowels into the end
panel .
Repeat on the other end
panel .
Fitting cams and dowels
into the bottom panel.
Insert 4 cams into
the bottom panel .
Flip the panel over.
Insert 2 dowels into
the bottom panel .
1454
A
B
x8
A
x4
A
A
B
B
B
B
Step 5
1454 x2
1454
A
B
B
x2
A
x4
B
1453
1453
A
A
A
A
1453
1453
Step 6
A
A
A
A
B
B
A
A
Fitting cams and dowels
into the end panel and
the back rail.
Insert 4 cams into the
back rail .
Insert 2 cams and 2
dowels into the end
panel .
1459
1458
1458
1459
A
B
A
B
x2
A
x6
NOWTURN PANEL OVER
B
B

Assembly Instructions
7
Step 7
Step 8
Fit divders to the shelf
panel.
Connect the cams in the
divider panels to the
dowels in the shelf panel
.
Turn cams 180 degrees to
lock.
1456
1455
1455
1456
1456
Attach the bottom
panel to the divider
panel.
Connect the cams in the
divider panel to the
dowels in the bottom panel
.
Turn cams 180 degrees to
lock.
1456
1453
1456
1453
Step 9
Attach the end panels
to the bottom and shelf
panels.
Connect the cams in the
shelf and bottom
panel to the dowels
in the end panels .
Turn cams 180 degrees to
lock. 1453
1455
1454
1454
1455
1453
1454

Assembly Instructions
8
Step 10
Step 11
E
x1
Screw the foot onto the
bottom panel using
screw .
Stand the unit upright.
Fit the foot.
Attach the top panel
to the end and divider
panels.
Insert the cams in the
end panels and
divider panel into the
dowels in the top panel
.
C
1456
1452
1454
1452
1454
1454
1456
E
C
x1
E
C
1453
1453
Step 12
Fit the back panel to
the end panel.
Insert the cams on the
back rail into the
dowels on the end panel
.
1459
1458
1459
1458

Assembly Instructions
9
Step 13
Insert dowels and
plastic inserts into the
top panel.
Insert 4 dowels and 4
plastic inserts into the
top panel .
1457
Step 14
IMPORTANT!
Only follow the 2 steps on
this page if you are going to
have the shelf section on the
left. If you are going to have
the shelf section on the right,
follow the 2 steps on the next
page.
B
x4
D
x4
B
B
B
B
D
D
D
D
B
D
1457
Attach the back rail and
end panel to the top
panel.
Insert the cams in the back
rail and end panel
onto the dowels in
the top panel .
1457
1457
1459
1458
1459
1458

Assembly Instructions
10
Step 15
Insert dowels and
plastic inserts into the
top panel.
Insert 4 dowels and 4
plastic inserts into the
top panel .
1457
Step 16
IMPORTANT!
Only follow the 2 steps on
this page if you are going to
have the shelf section on the
right. If you are going to have
the shelf section on the left,
follow the 2 steps on the
previous page.
B
x4
D
x4
B
B
B
B
D
D
D
D
B
D
1457
Attach the back rail and
end panel to the top
panel.
Insert the cams in the back
rail and end panel
onto the dowels in
the top panel .
1457
1457
1459
1458
1459
1458

Assembly Instructions
11
Step 17
Insert dowels and
plastic inserts into the
top panel.
Lower the desktop
onto the shelf top .
Using bolts screw up
through the shelf top
and into the plastic inserts
in the desktop .
1457
IMPORTANT!
Only follow this step if you are going to
have the shelf section on the
left. If you are going to have
the shelf section on the right,
follow the next step.
F
x4
D
F
1452
1452
1457
1452
1457
F
F
F
F

Assembly Instructions
12
Step 18
Insert dowels and
plastic inserts into the
top panel.
Lower the desktop
onto the shelf top .
Using bolts screw up
through the shelf top
and into the plastic inserts
in the desktop .
1457 IMPORTANT!
Only follow this step if you are going to
have the shelf section on the
right. If you are going to have
the shelf section on the left,
follow the previous step.
F
x4
D
F
1452
1457
1452
1457
F
F
F
F
1452

Assembly Instructions
13
Step 19
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
With help move the
unit into position.
Warning:
2 people required.
Lift with care.
Warning:
H
x1
G
x2
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
An attachment device is provided with your
product. However you will need to source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
Always ensure the wall to be drilled is free
from hidden electrical wires, water and gas
pipes.
Use the wall attachment device provided.
Never allow children to climb or hang on
drawers, doors or shelves.
Place heaviest items in the lower drawers
or shelves.
Unless specifically designed to accomodate,
do not set TV’s or other heavy objects on
top of this product.
Never open more than one drawer at a time.
WARNING
Shelf section on the left
Shelf section on the right

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, SouthYorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)

Notes;