J D Williams Oliver Storage Unit User manual

Dimensions
Width - 30cm
Depth - 30cm
Height - 86.5cm
Important– Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference
Issue 1 - 23/10/17
Oliver Storage Unit
YO828
464/3944

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers
WARNING
In order to help prevent overturning –
To help prevent product toppling over please follow the below steps:-
Do not allow children to climb or hang on the furniture
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
You will need to provide wall plugs and screws applicable for your wall type

2
Components -Panels
Please check you have all the panels listed below
Top Panel x 1
(30(w) x 30(d) cm)
Middle Panel x 1
(30(w) x 30(d) cm)
Left Side Panel x 1
(56.5(h) x 29.8(d) cm)
Right Side Panel x 1
(56.5(h) x 29.8(d) cm)
Base Panel x 1
(23.8(w) x 29.8(d)
Upright Bars x 4
(24(w) x 3(d) cm)
Shelf Panel x 1
(23.5(w) x 26.4(d) cm)
Door Panel x 1
(46(h) x 23.2(d) cm)
Back Panel x 1
(47(h) x 24.6(d) cm)

Tools required
Phillips screwdriver
(medium & large)
Ruler – Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
Note:
may be supplied than are required.
3
12 12 14mm Screw x 6
Dowel x 12 Hinges x 2
14mm Screw x 1
Wall Strap x 1
50mm Screw x 4 Camlock covers x 4
Shelf Supports x 4
Panel Stiffeners x 6
Washer x 2
14mm Screw x 12
Handle x 1 18mm Screw x 1

a: b: c:
a: To move the top panel up
or down, loosen screws
shown and move top panel to
suit
b.To move the top panel in or
out, loosen screws shown
and move top panel to suit.
Retighten screws
C:To move the top panel left
or right, adjust screws
shown.
Adjusting Hinges
Hinge adjustment:
4

5
Assembly Instructions
Step 1
Step 2
1. Into the underside of
Top Panel 1 Middle Panel
and Side panels 3 and 4,
insert a total of
12 x Male Camlocks
as shown.
A
AA
A
A
AA
A
A
A
A
A
1
2
3
4
6
6
6
6
N
N
N
N
2
D
D
D
B
O
6
B
O
O
B
BB
1
12
34
A
1. Insert 4 x Dowels into
the ends of 4 x Upright
Bars
2. Connect Upright Bars 6
to Top Panel 1 as shown.
Insert 4 x Female Camlocks
as shown. Use a
screwdriver to turn the
Female Camlocks
Clockwise to lock
For more information refer
to the Using Camlocks
Section
3. Cover Female Camlocks
with 4 x Camlock Covers Q
4. Connect Middle Panel 2
to Uprights using 4 x Screws
N
D
6
6
1
B
O
2
N

6
Assembly Instructions
Step 3
Step 4
.
Step 5
1. Into Base Panel 2 insert
4 x Dowels D as shown.
2. Connect Side Panels 3
and 4 to base Panel 5
3. Into the underside of
Base Panel 5 Insert
4 x Female Camlocks
as shown. Use a
screwdriver to turn the
Female Camlocks
Clockwise to lock
For more information refer
to the Using Camlocks
Section
D
3
4
5
D
D
D
D
BB
B
B
9
1
2
D
D
D
BB
B
B
5
D
3
45
5
B
1.Slide Back Panel 9
into position
9
1. Into Side Panels 3 and
4 insert a total of 4 x
Dowels D
2. Locate Middle Panel 2
onto Side Panels
3. Into holes shown in
Side Panels 3 and 4
Insert 4 x Female
Camlocks as shown.
Use a screwdriver to turn
the Female Camlocks
Clockwise to lock
For more information refer
to the Using Camlocks
Section 34
3
4
D
2
34
B

Assembly Instructions
Step 6
7
Step 7
1. On the reverse of the
unit install 6 x Panel
Stiffeners M as shown
using 6 x Screws C
2. To Top Panel 1 fit 1 x
Wall Strap L as shown
using 1 x Wahers I and
Screw G
1. Into Side Panels 3
and 4 insert 4 x Shelf
Supports H
2. Onto Shelf Supports
install Shelf 7 as shown
9
M
C
G
I
L
L
IG
7H
MC
1
1
L
I
G
3
4
H
3
4
7

8
Assembly Instructions
Step 8
Step 9
E
E
E
E
E
E
E
E
J
K
8
I
The unit is floor
standing, but it is
recommended that the
unit is secured to the
wall.
1. Move the unit into
desired position.
2. Mark the wall with a
suitable scribe the
position of the fixing
hole.
3. Drill hole and insert a
suitable Wall Plug,
Please check the type of wall
you are fixing to and for more
information please see the
guide to wall mounting
& Fixings on the back page
Warning:
Before driling,check
wall for hidden pipes
and cables.
4. Secure the strap to the
wall using 1 x Washer
and a suitable wall screw
Note: To hide the straps
behind the unit, drill the
holes lower than the top of
the unit
I
2. Fit the door to the unit by
connecting the Hinges D
to Side Panel 5
using 4 x Screw E
per hinge
3. Fit Handle J to the door
using 1 x Screw K
1. Connect 2 x Hinges D
to Door using
2 x Screw E per Hinge
F
F
F
3
F
8
E
F
3
E
J
K