jablotron JA-63 PROFI" User manual

JA-63 „PROFI“ Alarm system
Installation manual

This manual is valid for control panel model JA-63 version GK61005 (control panel board) and DY61232 (telephone
communicator board).
The use of Comlink Windows v. 57 software or higher is required for this control panel and can be obtained from our home
page at www.jablotron.cz

JA-63 „PROFI“ Alarm System - 3 - MGK51404
Contents:
1Architecture of the control panel.............................................................................................................................................................................4
2Control panel installation........................................................................................................................................................................................5
2.1 Power cable wiring............................................................................................................................................................................................5
3Antenna for the radio module.................................................................................................................................................................................5
3.1 Rubber rod antenna used in the control panel..................................................................................................................................................5
3.2 External antenna use........................................................................................................................................................................................5
4Connection of a telephone line to the digital telephone communicator..................................................................................................................5
5Terminals and connectors on the main board.......................................................................................................................................................6
6The JA-60 keypad(s)..............................................................................................................................................................................................7
7Installation of wireless items...................................................................................................................................................................................8
8Back up battery installation ....................................................................................................................................................................................8
9First powering of the control panel .........................................................................................................................................................................8
10 Control panel programming....................................................................................................................................................................................8
10.1 Enrollment (teaching) of wireless items enter: 1......................................................................................................................................10
10.2 Hard-wired zone input setting sequence: 60 nn xys.................................................................................................................................10
10.3 Exit / Entrance delay sequence: 2 1 x.....................................................................................................................................................11
10.4 Alarm duration sequence: 2 2 x...............................................................................................................................................................11
10.5 PgX and PgY output functions sequences: 2 3 x & 2 4 x......................................................................................................................11
10.6 Recorded message and phone number editing in the user mode sequence: 2 5 x ............................................................................11
10.7 Radio signal jamming testing sequence: 2 6 x.........................................................................................................................................12
10.8 Regular communication checking sequence: 2 7 x..................................................................................................................................12
10.9 Reset enabled sequence: 2 8 x................................................................................................................................................................12
10.10 Arming control of a subsystem sequence: 2 9 0.......................................................................................................................................12
10.11 Enrollment of the control panel to a UC-2xx or to a master control panel sequence: 2 9 9.....................................................................13
10.12 No code requested for , , , (F1, F2, F3), F4, F8 & F9 sequence: 3 0 x .....................................................................13
10.13 Partial (Home) arming with - non split control panel sequence: 3 1 x ............................................................................................13
10.14 Hard wired siren alarm enabled sequence: 3 2 x.....................................................................................................................................13
10.15 Exit delay audible indication sequence: 3 3 x...........................................................................................................................................13
10.16 Partial arming exit delay audible indication sequence: 3 4 x....................................................................................................................14
10.17 Entrance delay audible indication sequence: 3 5 x ..................................................................................................................................14
10.18 Arming and disarming chirps with wired siren sequence: 3 6 x................................................................................................................14
10.19 Siren alarm in Disarm & Partial arming sequence: 3 7 x........................................................................................................................14
10.20 Wireless siren alarm sequence: 3 8 x.......................................................................................................................................................14
10.21 Indication of system problems when arming sequence: 3 9 x..................................................................................................................14
10.22 Control panel splitting sequence: 690 x....................................................................................................................................................15
10.23 Only first source of alarm is recorded sequence: 691 x ...........................................................................................................................15
10.24 Alarm triggered by opened zone when arming sequence: 692 x .............................................................................................................15
10.25 Addressing of wireless detectors to sections sequence: 61 nns ...........................................................................................................15
10.26 Addressing of the user codes to sections sequence: 62 nns ...................................................................................................................16
10.27 Addressing of wireless controllers to sections sequence: 63 nns ............................................................................................................16
10.28 Automatic arming / disarming setting sequence: 64 nahhmm..................................................................................................................16
10.29 New service code setting sequence: 5 nSC nSC.....................................................................................................................................17
10.30 User Mode entering Sequence: 6 9 9 9...................................................................................................................................................17
10.31 Real time and date setting sequence: 4 hh mm dd MM YY .....................................................................................................................17
11 System testing......................................................................................................................................................................................................17
12 Voice & SMS messages setting...........................................................................................................................................................................18
12.1 Telephone numbers for voice message sending sequence: 7xxx....xxFy ................................................................................................18
12.2 Automatic SMS sending sequence: 7xxx....xxF5 ....................................................................................................................................19
12.3 Voice message(s) recording sequence: 8x ..............................................................................................................................................19
12.4 Triggering of voice and SMS messages sending sequences: 9 y x .........................................................................................................19
12.5 Dialing method sequence: 9 0 x ...............................................................................................................................................................20
12.6 Telephone line checking sequence: 9 9 x ................................................................................................................................................20
12.7 Telephone dialer testing sequence: 8 9....................................................................................................................................................20
13 To enable a remote computer to dial in................................................................................................................................................................20
13.1 Reaction to an incoming call sequence: 05...............................................................................................................................................21
13.2 Remote access code setting sequence: 07...............................................................................................................................................21
14 Central monitoring station communication setting................................................................................................................................................21
14.1 Reporting codes setting sequences: 00 and 01 ........................................................................................................................................22
14.2 Account ID code setting sequence: 02......................................................................................................................................................22
14.3 Protocol and Format setting sequence: 03................................................................................................................................................23
14.4 Re-dialing pause setting sequence: 04 .....................................................................................................................................................23
14.5 CMS phone number entering sequence: 06..............................................................................................................................................23
14.6 Digital communicator reset sequence: 096060 .........................................................................................................................................24
15 Control panel factory default reset .......................................................................................................................................................................24
16 Central Monitoring station report codes table.......................................................................................................................................................25
16.1 Internal structure of Contact ID protocol....................................................................................................................................................26
17 Personal Computer used with JA-63....................................................................................................................................................................27
18 Remote access to the system..............................................................................................................................................................................28
18.1 Establishing connection with a remote control panel by computer............................................................................................................28
19 Recommended Professional installer basic rules.................................................................................................................................................28
20 Trouble shooting table..........................................................................................................................................................................................28
21 Possibilities to extend the system ........................................................................................................................................................................29
21.1 Extension of the system with a subsystem................................................................................................................................................29
21.2 Brief overview of parts suitable for the JA-63 system................................................................................................................................29
21.3 Wireless items - can be used with a wireless version ...............................................................................................................................29
21.4 The digital bus items:.................................................................................................................................................................................30
21.5 Wire operated items ..................................................................................................................................................................................30
22 Control panel specifications: ................................................................................................................................................................................31

JA-63 „PROFI“ Alarm System - 4 - MGK51404
This product should be installed by professional installers. The manufacturer assumes no liability for damages caused by
incorrect installation or improper use of this system.
1 Architecture of the control panel
The JA-63 "Profi" is a fully programmable control panel with building block architecture. By programming, it can be split
into two separately operated sections (with a shared section). It has a built in power supply and there is ample space for a
back up battery (12V, 1.3Ah or 2.6Ah) in the control panel case.
The JA-63K main board has 4 hard-wired inputs with programmable triggering (NC, balanced or double balanced)
and programmable reactions.
Model JA-63KR (equipped with the “R” radio communicating module) has 16 wireless zones. Up to two JA-60 detectors can
enrolled into each zone (totally 32 as a maximum). In total model 63KR has 20 zones (4 wired and 16 wireless). Up to 8
wireless controllers (remote controls or wireless keypads), a JA-60A wireless siren and unlimited number of UC family
wireless output modules can be enrolled as well. If more zones are required, another JA-6x control panel can be enrolled
as a subsystem (Master & Slave architecture). The master control panel receives information from the sub control panel
and it can also arm and disarm the subsystem panel.
Telephone module “X” can communicate with a Monitoring Station, send two voice messages, send five SMS
messages via SMS server (or dial a numeric Pager) or. It can also communicate with a remote PC (using ComLink SW
and a JA-60U modem).
GSM dialer JA-60GSM sends SMS messages, calls to predefined telephone numbers and plays audible warning,
communicates with 2 CMS, allows remote access from a phone’s keypad and can be set via web page.
Operation and programming is possible via the JA-60E keypad (either directly wired to the control panel or remotely
using JA-60U modem). The control panel equipped with a radio module (63KR, 63KRX) can also be programmed and
operated by a JA-60F wireless keypad and can also be operated by RC-11, RC-22 or RC-60 remote controls or by a JA-
60D wireless keypad. Operation and programming is also possible via a PC using ComLink SW (locally or remotely via
JA-60U modem).
the internal layout
Available models of the JA-63 system
control panel R
module X module GSM module description
JA-63K no no no four zone hard wired control panel
JA-63KR yes no no 16 zones wireless (up to 32 detectors) & 4 hard wired zones
JA-63KRX yes yes no 16 zones wireless (up to 32 detectors) & 4 hard wired zones & digital
telephone communicator.
JA-63KRG yes no yes 16 zones wireless (up to 32 detectors) & 4 hard wired zones & GSM dialer.
Note: Radio module R can not be ”aftermarket” installed into 63K and 63KX models. Telephone communicator X module and GSM dialer JA-60GSM can be
installed additionally to a 63K or 63KR control panels.

JA-63 „PROFI“ Alarm System - 5 - MGK51404
2 Control panel installation
•The control panel should be easily accessible but not visible. There should be a power socket available and also a
telephone line (if the system has an optional built in dialer).
•Attach the control panel’s rear housing to the wall (see drilling diagram on the last page of this manual).
•Route all the cables to the control panel (power, input loops, telephone line etc.) before you tighten the case to the
desired location.
Note: Only a qualified technician can provide the installation, telephone line connection and servicing. User is not allowed
to open the cover and/or make any modification.
2.1 Mains supply connection
It is specified to connect the control panel by a permanent two-wire
cable. The power supply has a double isolation. The ground wire is
unattached.
•An inlet is realized by a permanent two-wire cable with a double
isolation – wire diameter 0.75 – 1.5 mm2. The inlet must be connected
to the independent circuit breaker (10 A max) in the object, which has
function of the switch.
•Thread the Inlet through the power supply case bushing; connect the
wires to the terminals (equipped by a fuse T100mA / 250 V).
•Cable must be firmly fixed to the power supply board by a sliding strap (firstly check again that the wires are firmly
secured in terminals)
3 Antenna for the radio module
If the “R” radio module is used, install its antenna (rubber rod or an external model AN-01). The antenna must not be
shielded by any metal object in its proximity. The working range of the wireless accessories is about 100 meters under
optimal conditions. However, building materials can absorb or obstruct radio signals and communication can also be
effected by interference from other radio signals. For these reasons, you should anticipate a shorter working range for indoor
installations.
3.1 Rubber rod antenna used in the control panel
There is a hole on the top of the control panel case for the rubber antenna. The rubber
antenna is supplied with the control panel. Attach the antenna to the board using the
provided screw as shown in the diagram. The antenna must not be obstructed by any metal
object.
3.2 External antenna use
An optional external antenna, model AN-01, has a connector which fits the connector on
the radio module board. If you use the external antenna, the rubber antenna should not be
installed. The AN-01 antenna has a small plastic ring on its end, used to hang it from the
wall. Its active part (from the plastic ring to the coil) should be installed vertically and should not be obstructed by any
large metal object. The antenna can be located behind furniture, etc.
4 Connection of a telephone line to the digital telephone communicator
If the 65X module is installed, the control panel can communicate with a Monitoring
Station, send voice messages, SMS messages and dial a numeric Pager as well as
communicate with a remote PC. A standard analog telephone line (type TNV 1-3) must be
connected to the module for these functions.
•Use the provided telephone cable to connect the telephone line to the IN jack on the
X module (see diagram )
•Connect a telephone, fax or other phone operated device to the OUT jack, marked
with a phone symbol
•When the control panel is in normal stand by mode, the phone line and any attached
device will operate as normal
Note: The communicator must be plugged directly to a telephone line socket. All other devices (telephone, facsimile
machine, modem etc.) should be connected to the communicator output.

JA-63 „PROFI“ Alarm System - 6 - MGK51404
5 Terminals and connectors on the main board
There is a Digital data jack for the JA-60E keypad(s) and/or for a PC interface cable. The same connecter is also
available on the bottom right corner of the control panel housing. The digital bus signals are also available on terminals
1234.
1,2,3,4 digital data terminals provide an option to use standard
cable for the wiring of JA-60E keypads.
Up to four JA-60E keypads can be wired to the control panel
(connected in parallel). The total length of the keypad cables should
not exceed 100m. If using the jack connectors, the data cable length
should not exceed 10 meters. Use ordinary twisted pair cable
connected to the 1234 terminals for longer distance.
AC20V – output of the power transformer (20VAC) is connected to
this pair of terminals.
L1,L2, L3, L4 – hard wired zone inputs – detector outputs can be
wired here: see examples of wiring on page 7. For each input it is
possible to program its method of triggering: Normally Closed loop,
balanced loop (2k2) or double balanced loop (2x 1k1) and the type
of reaction of the system (see section 10.2).
Factory default setting: all inputs are triggered as balanced loops,
reactions: L1= delay, L2= next delay, L3= instant a L4= tamper
COM common terminal to close (balance) the input
NO is a normally open contact of the alarm output relay.
NC is a normally closed contact of the alarm output relay.
C is a common contact of the alarm output relay, max. load 60V /
1A. The relay is turned on during any alarm.
SIR is an external siren output. In the normal mode it has a +U
terminal voltage. In the alarm mode it has a GND terminal potential.
Connect an ordinary external siren to +U and SIR terminals (max. load
0,7 A). A two wires back up siren should be connected to the GND and
the SIR terminals (during an alarm, the charging will temporarily halt).
The siren can also be used for arming and disarming chirps and as an
audible indicator while in the testing mode (see section 10.18).
PGX, PGY are outputs (switching to GND when activated, max. 12V, 100mA). The function of these outputs are determined by
the setting in the programming mode (see 10.5). The control panel also wirelessly transmits the PGX and PGY
signals and UC receiving units can be used as remote outputs for these signals.
+U is a back up power output for external items (detectors etc.). The max. permanent current is 0.4A (1.2 A for max. 15
min - not more then one cycle per hour). This output is fused (FU2 1.6A) and supervised by the control panel. If it is
overloaded, a control panel failure will be indicated (fault C).
GND is a common ground terminal for power output (-).
RADIO
MODULE
JA-63R

JA-63 „PROFI“ Alarm System - 7 - MGK51404
Fig. 1 – Wiring examples
6 The JA-60 keypad(s)
The system can be programmed and operated by JA-
60E keypad(s). As a maximum, 4 keypads can be wired
to the control panel. The keypads can either be wired by
cables equipped with modular jacks or by standard
cables to terminals 1234. The same numbered terminals
(pins in the connectors) must be linked together. It is
possible to combine arbitrary wiring with modular
connectors and ordinary cables - see diagram. Modular
jack cable should not be used for a distance longer than
10 meters.
The JA-60E keypad can also be connected remotely
via the JA-60U modem.
When a control panel has a „R“ radio module, it can
also be operated and programmed via a JA-60F
wireless keypad(s). The wireless system can also be
operated by remote controls RC-11, RC-22 & RC-60,
as well as by a JA-60D wireless keypad. The control
panel can have up to 8 wireless controllers.
It is also possible to operate and program the JA-63
system via a connected PC with ComLink software. The PC can be connected locally with or remotely, using a JA-60U
modem (see section 17 and 18).

JA-63 „PROFI“ Alarm System - 8 - MGK51404
7 Installation of wireless items
If the control panel is equipped with a “R” radio module, it can work with all types of JA-60 wireless items and wireless
UC output modules (see brief overview of items in section 21.1).
•Detectors – up to 32 wireless JA-60 detectors can be enrolled to the control panel (two detectors can be enrolled
to each zone)
•Keypads and remote controls - up to 8 wireless controllers can be enrolled to the control panel (JA-60F and JA-
60D keypads, RC-11 and RC-22 remote controls)
•JA-60A Wireless siren – one can be enrolled to A position, if more sirens requested they can also be enrolled to
detectors positions
•Wireless output modules UC-216 and UC-222 have relays, which copy the status of the control panel’s
programmable outputs PgX and Pg Y. An unlimited number of the UC modules can be used with each system.
•A JA-6x control panel can be enrolled as a subsystem if more zones are required (Master & Slave architecture).
The master control panel receives information from the sub control panel and it can also arm and disarm the
subsystem panel if requested.
Follow the particular wireless item manual when installing. After you install the item to the desired location, leave it un
powered and without its cover. The method of enrollment is described in section 10.1.
8 Back up battery installation
There is a space for a size 12V, 1.3 or 2.6Ah battery (battery size should corresponding to a desired backup period).
The control panel recharges and checks the condition of the back up battery. If the system is powered from the battery
for an extended time and the battery is nearly discharged, the control panel will first trigger a technical alarm and it will
then disconnect the battery to prevent damage. After the main power is on again, the battery will be re-connected and will
be recharged.
•insert the battery into the control panel
•connect the battery cables (red +, black - )
Warning - do not make any short connection of the battery terminals!
9 First powering of the control panel
•Check that all cables are connected correctly
•Switch on the AC power – the self testing LED in the control panel will start to flash
•The JA-60E keypad will display a "P", confirming that the system is in the programming mode (ready for setting).
If a wireless keypad JA-60F will be used in the system, it should be enrolled at first - see part 10.1.
Note: if „P“ is not displayed, the control panel is not in the factory default setting. Perform a Factory default reset. (See section 15).
10 Control panel programming
Functions of the system can be customized. The most convenient programming method is via a connected PC using the
Comlink software (see 17). Programming can also be performed manually from the keypad:
•If the control panel is not in the programming mode, open it (entering F 0 SC - SC = Service Code, factory
default SC=6060) – The programming mode will be indicated by a „P“ on the LED display. This mode can only be
entered when the panel is disarmed. In this mode, no alarm can be triggered. In the “P” mode, detectors and
other accessories can be enrolled, the system parameters can be set up and the system can be tested.
•Any unfinished programming sequence can be terminated by pressing the N key.
•To exit the programming mode, press the N key („P“ will turn off). If any fault is indicated when you try to exit
the programming mode see programming sequence 39x for more details.

JA-63 „PROFI“ Alarm System - 9 - MGK51404
List of control panel programmable parameters
Function sequence options factory note
Enrolling of detectors and controllers 1 1& 7scroll, 2 erases item - Rmodule
Hard-wired zone input setting 60 nn xyz nn– zone, x– triggering,
y– reaction, s- section
L1=delay
L2=next d.
L3=instant
L4=tamper
Exit / Entrance delay 21x x= 1 to 9 (x 10sec.) 30sec.
Alarm duration 22x x = 1 to 8 (min.), 0=10s,
9=15min 4min.
Function of PgX output 23x x= 0 to 8 (0-Chime, 1-Fire,
2-Arm, 3-Panik, 4-Alarm, 5-
Door, 6-Home, 7-No AC, 8-By
phone)
Chime different
when split
Function of PgY output 24x x= 0 to 8 (0-Chime, 1-Fire,
2-Arm, 3-Panik, 4-Alarm, 5-
Door, 6-Home, 7-No AC, 8-By
phone)
Arm when split
different
Voice m. & tel. Numbers editable in the user mode 25x 251 = YES 250 = NO NO Xmodule
Radio signal jamming regular testing 26x 261 = YES 260 = NO NO Rmodule
Regular communication check enabled 27x 271 = YES 270 = NO NE Rmodule
RESET enabled 28x 281 = YES 280 = NO YES
Subsystem arming enrollment 290 will enroll to sub-control panel as wireless
controller Rmodule
Control panel teaching to a UC-2xx, master-system,... 299 will enroll as control panel Rmodule
No code requested for , , , F4 & F9 30x 301 = YES 300 = NO YES
Partial (Home) arming enabled 31x 311 = YES 310 = NO YES
Siren alarm enabled 32x 321 = YES 320 = NO YES
Exit delay audible indication enabled 33x 331 = YES 330 = NO YES
Partial arming exit delay audible indication 34x 341 = YES 340 = NO NO
Entrance delay audible indication enabled 35x 351 = YES 350 = NO YES
Arming & disarming chirp sounds enabled 36x 361 = YES 360 = NO NO
Siren in Disarm & Partial arming enabled 37x 371 = YES 370 = NO YES
Wireless siren alarm enabled 38x 381 = YES 380 = NO YES Rmodule
Indication of system problems when arming 39x 391 = YES 390 = NO NO
Split control panel (A, B & C sections) 690x 6901 = YES 6900 = N0 NO
Only first source of alarm is recorded 691x 6901 = YES 6910 = NO NO
Alarm triggered by opened zone when arming 692x 6921 = YES 6920 = NO NO only if 391
Addressing of wireless detectors to sections 61 nns nn– zone n., s- section 1-10A
11-16B Rmodule
Addressing of user codes to sections 62 nns nn– code n., s- section all A when split
Addressing of wireless controllers to sections 63 nns nn– controller n., s- section all A Rmodule
Automatic arming / disarming 64nahhmm n- 0-9, a-action, hh-hours,
mm-min. all off
Service Code changing 5 nSC nSC nSC = new Service Code 6060 code 2x
User Mode entering 6999 Goes to the User mode -
Real time and date setting 4 hh mm DD MM RR 00 00 01 01 00

JA-63 „PROFI“ Alarm System - 10 - MGK51404
10.1 Enrollment (teaching) of wireless items enter: 1
The wireless control panel (63KR or 63KRX) can enroll up to 32 wireless detectors (2 in each zone), up to 8 controllers
(remote controls & keypads), wireless sirens and an additional JA-6x control panel as subsystem:
•Press key 1 (while „P“ is displayed) to enter the enrolling mode. The control panel will display the next free position
to enroll a detector.
oIf no JA-60E keypad is used in the installation and you need to enroll a wireless JA-60F keypad:
connect (short ) the RESET pins on the control panel board (it will open the learning mode)
install batteries to the JA-60F keypad and wait until the keypad enrolls. Enrollment will be
confirmed on the keypad.
disconnect the RESET pins and then use the keypad to enroll all the other items in following way
•Use key 1 and 7 to scroll (up and down) all control panel wireless positions – 1 to 16 (detectors) – c1 to c8
(controllers & keypads) – A (wireless siren) – J (sub control panel JA-6x). The display shows the position number
while the Battery LED indicates if the position is occupied. The system will not allow enrollment of an item into a non-
corresponding position (a detector can not be enrolled into a controller position etc.).
•Detectors and keypads are enrolled after their power is switched on (batteries are installed). A remote control is
enrolled after both of its buttons are simultaneously pressed and held for 3 seconds. A subsystem control panel will
enroll after sequence 299 is entered while it is in its programming mode.
•Control panel confirms enrollment with a „beep“ (press F to get confirmation by a wired siren). The display will
show the number of the enrolled item for 2 seconds and then it will display the next free position.
•Second detector enrolment to a zone – select the zone into which you want enroll the second detector. Press
shortly key 5 (selects second position) and then install battery to the detector. Enrollment of the second detector will
be indicated by the Fault LED. If there are two detectors in a zone, all indicators in this zone (alarm, tampering, low
battery etc.) will be common for both enrolled detectors (for example, if any of the two detectors is tampered with, the
zone will indicate tampering.).
•To change the position of an enrolled item - simply enroll it to the new selected position (the item will „move“). If
you enroll an item to an occupied position, the former item will be deleted and only the new enrollment is valid.
Normally only one item (detector, controller etc.) can be stored to each position.
•Erase an enrolled item by selecting the corresponding position and then press and hold key 2 for two seconds. The
item will be erased (confirmed with a long beep). If you press and hold key 3, all enrolled controllers (remote controls
and keypads) will be erased. Pressing and holding key 4 will erase all enrolled items (detectors, controllers, siren and
the sub system). If two detectors were enrolled in a zone, both of them will be erased if you erase the zone’s position.
•The JA-60A wireless siren will enroll (to position A) when its power is switched on. If you need to enroll a siren
which is already powered and it is not possible to easily switch off its power, you can enroll it the following way: enter
the enrolling mode and then enter the 6 digit siren production code (printed in the siren’s manual). The control panel
will “request” the siren to enroll. The siren will do that only if it has no current communication with any other control
panel (This protects you from enrolling your neighbor’s siren).
•Multiple outdoor sirens or multiple subsystems enrolment – enter 000000 while in enrolling mode. After this
outdoor sirens and JA-6x subsystems can be enrolled to positions 1 to 16.
•By pressing the button 8 in the enrolment mode the communication quality of the items can be checked
(LED indicator “battery” will start flashing). After receiving signal from the item the level of the signal is shown on the
display from 0 to 10 (corresponding to 0-100% in the ComLink software). In this mode it is also possible to adjust
level of audible indications by pressing the button F and scroll positions of the enrolled items by pressing buttons 1
and 7. Button N exits checking mode.
•To exit the enrolling mode press the Nkey
Note: if an item was not enrolled after its batteries were installed, it is because the control panel recognized its radio signal as a
weak one. Items are only enrolled if their radio signal has a level which guarantees reliable communication. Check the detector’s
batteries and try to enroll the problematic sensor once more. If it is not accepted by the control panel, you should change the location of
the item. All items should be located 1 meter as minimum from the control panel.
10.2 Hard-wired zone input setting sequence: 60 nn xys
If the hard wired L1 to L4 zones are used, their features can be programmed by entering:
60 nn xys
where: nn = zone number: 01 to 16
x= input triggering: 0 = off, 1 = Normally Closed, 2 = balanced loop (EOL resistor 2k2), 3 = double
balanced loop (EOL resistors 2x 1k1)
y= reaction: 0 = Instant, 1 = Delay, 2 = Fire, 3 = Panic, 4 = Tamper, 5 = Next delay, 6 = Arming control
s= address to section, 1 = A, 2 = B, 3 = C (shared common section, which is armed only if both A and B
sections are armed). If the control panel is not split, select s=1; if you select s=2 then this zone will be
automatically bypassed within partial arming. For details about splitting see section 10.22.
Notes:
•If you will not use a particular input at all, you can switch it off completely with parametr x = 0

JA-63 „PROFI“ Alarm System - 11 - MGK51404
•Next delay input (y=5) provides entrance delay only if at the moment of its triggering the entrance delay has been in
progress (activated before by any delayed input). If no delayed input is triggered before next delayed, the triggering
will cause an instant alarm.
•Addressing of inputs to section C when the control panel is not split has the same effect as addressing to section B
(i.e. automatic bypass while partial arming is used).
•If y=6 is programmed, then each triggering of this input changes arming status (arm – disarm – arm…) of the entire
system or just the corresponding section if the system is split.
Example: to set zone 2 input as a balanced loop with an instant reaction, addressed to section A, enter: 60 02 201
Factory default setting: L1 = delay, L2 = next delay, L3 = instant, L4 = tamper
10.3 Exit / Entrance delay sequence: 2 1 x
To change the duration of the exit and entrance delay (both of them) enter
21x (where xrepresents time in seconds x10). The delay can be selected from 10 to 90 seconds.
Example: to select an Exit and Entrance delay duration of 20 seconds, enter 212
Factory default setting is 30 seconds
10.4 Alarm duration sequence: 2 2 x
The alarm duration can be selected from 1 to 8 or 15 minutes entering:
22x (where x=time in minutes for1 to 8, x=9 means 15 minutes and x=0 means 10 seconds)
Example: to select an alarm duration of 15 minutes, enter 229
Factory default setting is 4 minutes
10.5 PgX and PgY output functions sequences: 2 3 x & 2 4 x
The control panel outputs PgX and PgY can have different functions, depending on parameter xin the corresponding
sequence:
2 3 x – determines triggering of PgX
2 4 x – determines triggering of PgY
where x represents the following functions (non split system):
0 Chime – triggered during the entrance delay (pre-alarm output)
1 Fire – triggered by a fire alarm (by a smoke or a gas detector)
2 Arm – activated when the control panel is armed (complete & partial arming)
3 Panic – activated when a silent panic alarm is triggered
4 Alarm – triggered by any audible alarm (except panic alarm)
5 Door – activated for 5sec. after (F3) entering (electric door lock opening)
6 Home – activated when the control panel is partially armed (Home arming)
7 No AC – triggered by an AC power failure
8 Phone/F8 – output can be operated remotely by phone or by SMS (if this feature is supported by installed communicator) or
locally from the keypad by F81 (ON) and F80 (OFF). If a code is requested to operate the system (see 10.12) then the F8x
instruction should be followed by a valid user code.
Note: the control panel also wirelessly transmits the PgX and PgY signals. Wireless output modules UC-216 and UC-222
can be used to receive the signals (see 10.11). The function of the UC module output relays is determined by the 23x and
24x setting.
Example: the PgX will work as a Panic output when 233 is entered, PgY as Door output when 245 is entered.
Factory default setting: PgX=Chime, PgY=Arm
10.6 Recorded message and phone number editing in the user mode sequence: 2 5 x
The User mode, which is accessible with F 0 “Master Code”, is for bypass setting, system testing and battery
replacement. This setting enables the user to change the voice message and telephone numbers of the built in dialer. If
the changes are enabled, then programming sequences for number programming, voice message recording and dialer
testing are accessible in the User mode. These settings have effect only when the control panel has a telephone
communicator module.
options: 2 5 1 changes enabled
2 5 0 changes disabled (no dialer programming in the User mode)
Factory default setting: changes disabled
If the system is split:
x 23x
(PgX) 24x (PgY)
0 Alarm A Alarm A
1 Alarm B Alarm B
2 Chime A Chime A
3 Chime B Chime B
4 Arm A Arm B
5 Door A Door B
6 Panic A Panic B
7 FIRE No AC
8 Phone/F8 Phone/F8

JA-63 „PROFI“ Alarm System - 12 - MGK51404
10.7 Radio signal jamming testing sequence: 2 6 x
When this function is enabled, the control panel will indicate trouble if the working band is jammed for more than 30
seconds. Jamming will trigger an alarm when the control panel is armed. Do not enable this testing if the control panel
does not have a radio module.
options: 2 6 1 testing enabled
2 6 0 testing disabled
Note: in large cities and some other locations the system can be randomly jammed from time to time (near TV or radio station, GSM
cell station etc.). In these cases the control panel can work without any problems because all important data is repeated, but the
jamming test should not be enabled. The level of the signals and interference can be observed using the Comlink software (see17)
Factory default setting: disabled
10.8 Regular communication checking sequence: 2 7 x
The control panel will check communication regularly with all enrolled items (detectors, keypads, siren etc.) when this
function is enabled. If communication is lost with any item, the control panel will indicate the fault of this item (when armed
it will also trigger an alarm). Do not enable this checking if the control panel does not have a radio module.
options: 2 7 1 checking enabled
2 7 0 checking disabled
Note: in large cities and some other locations with a strong radio interference the communication can be jammed randomly. The control
panel can detect such a strong interference as a temporary loss of communication with an item. Even in this case, the system is usually
able to work without any problems because all important data is repeated, but the communication check should not be used.
Factory default setting: checking disabled
10.9 Reset enabled sequence: 2 8 x
The factory default reset (see 15) can be disabled. This way no unauthorized future programming of the control panel
will be possible.
options: 2 8 1 reset enabled
2 8 0 reset disabled
Warning: if the Master or Service code is forgotten when the reset is disabled. The reset of the control panel will be possible only by
the manufacturer.
Factory default setting: reset enabled
10.10 Arming control of a subsystem sequence: 2 9 0
A wireless master control panel receives event signals (alarms, tampering, faults, low battery) from a JA-6x subsystem if
enrolled - see 10.1 a 10.11. This will cause the same kind of event on the master control panel and Jwill be indicated as
the source of the event on the keypad.
The master and slave control panels can be either armed and disarmed as two independent systems or the slave
system can follow the arming and disarming of the master. If the master should rule arming of the slave subsystem, make
the following settings:
a. enroll a subsystem to the master‘s J position (see 10.1 and 10.11),
b. place the master panel into the programming mode (P is indicated),
c. enter the enrolling mode in the sub-control panel (pressing key 1 while in the programming mode)
d. enter 290 on the master control panel – this way the master will enroll to the slave sub-control panel as a
wireless controller (to the first free position of c1 to c8)
e. turn both systems to standby mode and check that the subsystem will arm after the master control panel is
armed (in 2 seconds). Check the same for disarming
Notes:
•Master control panel generates wireless commands Arm and Disarm the same way as a remote control RC-11. The control
panel transmits these commands only if it has a subsystem enrolled in its position J.
•The Arm command is generated when the master control panel is completely armed and also at the end of an alarm while
the system remains completely armed (automatic alarm timeout). The Disarm command is generated when the master
control panel is disarmed, when it is partly armed (home arming or one section arming if it is split) and also in the end of an
alarm while the system is disarmed (manual termination of the alarm).
•The subsystem can also be operated by its other controllers (remote controls, keypads) if there are any. For better
understanding you can simply imagine, that the master control panel is just another remote control..

JA-63 „PROFI“ Alarm System - 13 - MGK51404
•Arming control of the subsystem by the master control panel can be disabled by erasing the corresponding cN position in
the sub-control panel. For example if the master control panel was enrolled to position c3, scroll to this position in the
enrolling mode and holding key 2 will erase the master control panel as a controller.
10.11 Enrollment of the control panel to a UC-2xx or to a master control panel sequence: 2 9 9
The wireless control panel can send data to output modules UC–216, UC–222 and UC-260 (see section 21). It can also
work as a subsystem of another JA-6x.
Enter the enrolling mode of the UC receiving device and then enter 299 on the control panel. Note that the control panel
must be in the programming mode. This enables the control panel to generate the enrollment signal.
If you want to enroll a subsystem to your control panel, enter the enrolling mode on the MASTER control panel (see
10.1.) and then enter sequence 299 in the programming mode of the sub control panel.
If the system is split, the sub control panel enrolls to the common shared section.
10.12 No code requested for , , , (F1, F2, F3), F4, F8 & F9 sequence: 3 0 x
If this parameter is enabled, no code is requested for the functions listed above. When this parameter is disabled, these
functions (keys) can be used only when followed by a code (Master or User) – see the following table:
function / setting 301 300
arming „code“
partial arming „code“
door opening „code“
memory reading F 4 F 4 „code“
appliance control F80, F81 F8 “code” 0
F8 “code” 1
message listening F 9 F 9 „code“
„code“ = Master or User
Factory default setting: no code requested
Note: this feature is also selectable on the JA-60D wireless keypad and it is independent from the control panel setting.
10.13 Partial (Home) arming with - non split control panel sequence: 3 1 x
In partial arming, the control panel reacts only to detectors addressed to section A (see 10.2 and 10.25) and it ignores
the triggering of detectors in section B or C (except smoke and gas detectors). Partial arming can be disabled with this
sequence.
options: 3 1 1 partial arming enabled
3 1 0 partial arming disabled
Factory default setting: partial arming enabled
10.14 Hard wired siren alarm enabled sequence: 3 2 x
The SIR siren output is activated when any alarm is triggered (except silent Panic alarm). This siren indication can be
disabled with this parameter.
options: 3 2 1 siren enabled
3 2 0 siren disabled
Factory default setting: siren enabled
10.15 Exit delay audible indication sequence: 3 3 x
The exit delay can be indicated by the “beeping“ of the keypad (for the last five seconds, the beeping is faster). The
audible indication can be disabled with this setting.
options: 3 3 1 indication enabled
3 3 0 indication disabled

JA-63 „PROFI“ Alarm System - 14 - MGK51404
Note: wireless indoor siren UC-260 also provides this indication (either following this setting or indicating no matter this setting)
Factory default setting: indication enabled
10.16 Partial arming exit delay audible indication sequence: 3 4 x
Partial arming with provides an exit delay for delayed reaction detectors. The exit delay for partial arming can be
indicated by the “beeping“ of the keypad (for the last five seconds the beeping is faster).
options: 3 4 1 indication enabled
3 4 0 indication disabled
Factory default setting: indication disabled
Note: when this indication is disabled, the confirmation of partial arming and disarming will automatically be silent, regardless of the 36x setting.
10.17 Entrance delay audible indication sequence: 3 5 x
The entrance delay can be indicated by a rapid “beeping“ of the keypad. This indication can be disabled with this
setting.
options: 3 5 1 indication enabled
3 5 0 indication disabled
Note: wireless indoor siren UC-260 also provides this indication (either following this setting or indicating no matter this setting).
Setting is also valid fro partial arming if system is split.
Factory default setting: indication enabled
10.18 Arming and disarming chirps with wired siren sequence: 3 6 x
The control panel can confirm on the SIR output arming (1 chirp), disarming (2 chirps), disarming with information in the
memory (3 chirps), andbypass or not ready component when arming (4 chirps). This parameter sets chirps on.
options: 3 6 1 siren chirps enabled
3 6 0 siren chirps disabled
Factory default setting: siren chirps disabled
Note: setting of chirp sounds is valid even if the siren is disabled for alarms with parameter 320. Partial arming is always silent, if sequence 340 is
selected. Chirp sounds can also be generated with the JA-60A wireless siren (self-contained setting in the wireless siren).
10.19 Siren alarm in Disarm & Partial arming sequence: 3 7 x
The SIR output can be disabled for alarms during the Disarm & Partial arming of the control panel (while somebody is
indoors). If the siren output is completely disabled for alarms with parameter 320, this setting has no effect.
options: 3 7 1 alarm in disarm & partial arming enabled
3 7 0 alarm in disarm & partial arming disabled
Factory default setting: enabled
10.20 Wireless siren alarm sequence: 3 8 x
The wireless siren alarm function can be disabled with this parameter. This setting will have no influence on the outdoor
wireless siren chirp sound function if enabled in the siren. This setting has effect only when the control panel is equipped
with a radio module:
options: 3 8 1 siren enabled
3 8 0 siren disabled
Factory default setting: siren enabled
10.21 Indication of system problems when arming sequence: 3 9 x
The system regularly checks the conditions of all items (detectors, keypads etc.). This setting ensures that the user will
be warned with 4 rapid beeps after arming, if any component of the system is not ready for arming. Cause of the problem

JA-63 „PROFI“ Alarm System - 15 - MGK51404
(for example permanently triggered detector, lost communication etc.) will remain displayed on the keypad. If the user
ignores this warning, the system will arm after the exit delay, then the problematic item will be bypassed for this arming
period. After disarming in such a mode, three beeps will be generated as well.
When the indication is not selected, the problematic item will be bypassed when arming with neither warning nor alarm.
If a permanently activated detector is deactivated during arming (for example your main door is not closed), the bypass of
this detector will be canceled automatically and the detector will be ready to trigger an alarm after it is activated (if you
close the door after the system is armed).
options: 3 9 1 warning enabled
3 9 0 warning disabled
Note: if this indication is enabled, the problems will also be indicated if there are any when leaving the programming or user mode.
Factory default setting: warning disabled
10.22 Control panel splitting sequence: 690 x
The control panel can be split into 2 independent sections A and B, with a shared common area C. This way the system
can be operated by two independent user groups. In fact the system in this mode works like two independent systems. If
the system is split into sections with this setting, it is possible to address detectors (both wireless and wired), user codes
and remote controls to the individual sections. Use the following sequences.
options: 6 9 0 0 no splitting (partial arming available in this mode)
6 9 0 1 splitting to sections A, B and common C (C is armed only when both A and B are armed)
Factory default setting: no splitting
10.23 Only first source of alarm is recorded sequence: 691 x
When any item triggers the alarm 4 times in a row the system will bypass it until any other events occurs. But it is
possible to set the limit at the incoming events so only the very first event during the entire alarm will be recorded. This
function is useful especially if the system contains a GSM communicator in order to decrease quantity of the SMS
messages. This setting is valid for all kinds of the alarm.
Options: 6 9 1 0 All sources of alarm are recorded
6 9 1 1 Only first source of alarm is recorded
Factory default setting: All sources of alarm are recorded
10.24 Alarm triggered by opened zone when arming sequence: 692 x
If the “indication of system problems when arming” (see 10.21) is enabled, it is also possible to test the status of the
detectors after expiring the exit delay. If any item is activated then in case of instant zone the alarm will be triggered
immediately, in case of delay zone the entry delay will start.
Options: 6 9 2 0 test disable
6 9 2 1 test enable
Factory default setting: test disabled
10.25 Addressing of wireless detectors to sections sequence: 61 nns
If the control panel is split (see 10.22) and is equipped with a radio module, the wireless detectors can be addressed to
sections by entering:
61 nns
where: nn = wireless detector zone number: from 01 to 16
s= section: 1 = A, 2 = B, 3 = C (common section - it is armed only when both A and B are armed). If the
control panel is not split, and s=2 is selected, this detector will be bypassed while partial arming.
Example: to address wireless detector zone number 3 to section A enter: 61 031
Factory default setting: detectors 1 - 10 are addressed to A, detectors 11 - 16 are addressed to B

JA-63 „PROFI“ Alarm System - 16 - MGK51404
actions' table
a no
splitting split system
0 no action no action
1 arm all arm all
2 disarm disarm all
3 partial
arming arm A
4 partial
arming arm B
5 disarm disarm A
6 disarm disarm B
10.26 Addressing of the user codes to sections sequence: 62 nns
If the control panel is split (see 10.22), the user codes can be addressed to sections A or B by entering:
62 nns
where: nn = user code number: from 01 to 14
s=section: 1 = A, 2 = B
Notes:
•If the control panel is not split, this setting has no effect.
•Master code (MC) can not be addressed. If the system is split, the use of MC
will arm all sections if no section is armed or it will disarm all sections if any
are armed. If you want to operate only section A with master code, enter F1
MC and F2 MC for section B.
Example: to address user code number 4 to section A enter: 62 04 1
10.27 Addressing of wireless controllers to sections sequence: 63 nns
If the control panel is split (see 10.22) and is equipped with a radio module, the wireless controllers (RC-11, RC-22 and
JA-60D) can be addressed to A or B section by entering:
63 nns
where: nn = number of the enrolled controller from 01 to 08 (c1 to c8)
s= section: 1 = A, 2 = B
Notes:
•If the control panel is not split, this setting has no effect
•For the JA-60F keypad this setting has no effect (its user codes are determined by 62 nns setting)
•The JA-60D keypad is effected the same way as RC-11 remote controls (is addressed to a selected section)
Example: to address controller number 5 to section A enter: 63 051
Factory default setting: all wireless controllers are addressed to section A
10.28 Automatic arming / disarming setting sequence: 64 nahhmm
The control panel can automatically arm and disarm for a requested period of a day. Up to ten instructions (time &
action) can be programmed in the period of one day by entering:
64 nahhmm
where: n= instruction number from 0 to 9
a= action (see the actions' table)
hh = hours (from 00 to 23)
mm = minutes (from 00 to 59)
Notes:
•If any automatic action is selected, it will be preformed everyday at the programmed time, following the internal control
panel clock.
•The automatic arming and disarming can be overridden manually anytime (by a user code or a remote control)
•If the control panel is in the requested arming mode before the action time, performance of the programmed action
will not change the arming
Example: to program an automatic complete arming of the system at 21:15 everyday enter: 64 0 1 21 15
Factory default setting: all instructions are set for no action

JA-63 „PROFI“ Alarm System - 17 - MGK51404
10.29 New service code setting sequence: 5 nSC nSC
The Service Code can be used to enter the programming mode. A new Service Code must be entered twice in a row to
avoid an error.
To change the code enter:
5 nSCnSC where nSC is your new Service Code (four digits)
Example: to change service code to 1276 enter: 5 1276 1276
Factory default setting: service code is 6060
10.30 User Mode entering Sequence: 6 9 9 9
This sequence is used to switch from the Programming Mode to the User Mode, where you can set zones´ bypass (see
User’s manual). You can exit the User Mode by pressing the “N” button. The bypassed zones will remain active after the
leaving the User Mode.
10.31 Real time and date setting sequence: 4 hh mm dd MM YY
The control panel has a built in real time clock. All events are stored to the event memory including the time of the
event. The clock should be set after the installation is completed. Time Setting:
4 hh mm dd MM YY
where hh = hours (24 hr. cycle)
mm = minutes
dd = day
MM = month
RR = year
Example: on Jun. 30 2007 at 17:15 enter: 4 17 15 30 06 07
After the control panel is powered, its internal clock’s default setting is: 00 00 01 01 00
Note: detail control panel event history can be viewed with a connected PC using Comlink software.
11 System testing
For testing by installer, the control panel should be in the programming mode - "P" indicated on the keypad’s LED (F0
Service Code). Testing can also be done by a user in the user mode (confirmed by “U”). The user mode is accessible
with the Master code. To open the user mode enter F 0 Master Code when the control panel is disarmed.
No alarm can be triggered in programming or user modes and any triggering of a detector (wireless or wired) will result
in a “beep” (press F to select a loud “beep” generated by a wired siren) and the display will briefly show which zone was
triggered. Enrolled wireless controllers, sirens and other items’ signals will be similarly indicated.
•Some detectors (JA-60P, JA-60N, JA-60B etc.) have an extra testing mode, which is activated for 5 minutes
after the detector’s cover is attached (see manuals of the particular detectors). If the detector is in testing mode,
it will indicate triggering locally with its LED, and it will also indicate the triggering on the control panel keypad’s
LED. Note that the JA-60P motion detector in normal mode (after 5 minutes testing mode) can not send next
triggering information until 5 minutes after the previous triggering was sent (this period can be shortened to 1
minute - see setting of the JA-60P detector).
•Triggering of a detector wired to one of the L1 to L4 inputs is indicated on the control panel keypad’s LED for
about 2 seconds after the triggering. So, if a detector is permanently triggered for a longer period, it will not be
indicated. If a double balanced input loop (2x 1k1) is used, then the control panel distinguishes triggering of the
detector from tampering.
•The best way of testing is via a connected PC using the Comlink software (see section 17). In the service
events window you will see a chronological record of all performed tests, including zone setting, quality of
communication etc.

JA-63 „PROFI“ Alarm System - 18 - MGK51404
12 Voice & SMS messages setting
A control panel equipped with the X module can automatically send 2 voice and 5 short text messages (or dial a Pager)
. The most convenient programming of the dialer is via a connected PC using the Comlink software (see section 17).
Programming can also be performed manually from the keypad:
•Enter the programming mode (F 0 Service Code, factory default = 6060), indicated by „P“
•Any unfinished programming sequence can be terminated by pressing the Nkey.
•To exit the programming mode, press the N key („P“ will turn off). If any fault is indicated when you try to exit
the programming mode, the control panel will inform you about the problem (see 10.21).
•Telephone numbers and messages can also be set up in the User Mode when enabled (see section 10.6)
List of the voice & SMS sending parameters
Function sequence
options factory d. note
Dialing method 90x 901 = tone 900 = pulse tone valid also for
CMS dialing
Triggering of the dialer with a Panic alarm 91x 0=nothing, 1=voice1 + SMS,
2=voice2, 3=SMS only 911
Triggering of the dialer with an Intruder alarm 92x 0=nothing, 1=voice1 + SMS,
2=voice2, 3=SMS only 921
Triggering of the dialer with a Fire alarm 93x 0=nothing, 1=voice1 + SMS,
2=voice2, 3=SMS only 931
Triggering of the dialer with a Tamper alarm 94x 0=nothing, 1=voice1 + SMS,
2=voice2, 3=SMS only 941
Triggering of the dialer with a Technical alarm 95x 0=nothing, 1=voice1 + SMS,
2=voice2, 3=SMS only 951
Telephone line checking enabled 99x 990=NO 991=YES NO
Store telephone numbers for voice message 7xx..x F y xx...x = tel. number, y=
memory 1 to 4, pause = F0
Automatic SMS sending 7x..xF9y..yF7
00F9F5 x..x=SMS server number y..y= mobile phone number
1:
2:
3:
4:
5:
Erase telephone number 7F0Fy y= memory 1 to 5, entering
7F0F0 erases all
Record voice messages (1 & 2) mess. 1 enter 85 then push button on X module and speak (10sec.)
mess. 2 enter 86 then push button on X module and speak (10sec.)
Dialer testing 89
12.1 Telephone numbers for voice message sending sequence: 7xxx....xxFy
Store telephone numbers for voice message by entering:
7 xx... xx F y
where xx...xx = telephone number
y= memory number from 1 to 4
A telephone number can have a maximum of 16 digits. A pause can be entered with F0
Example: to store tel. number 0 123456 to memory no. 2 enter: 7 0 F0 12345 F2
Note: enter a pause (F0) after the last digit of a number which is calling a mobile phone. This way the number will be called only
once and the dialer will not check the line signals (some mobile phone systems do not generate standard telephone line signals).
To delete a telephone number enter:
7 F0 Fy
where yis a memory number from 1 to 4
entering 7 F0 F0 will erase all tel. numbers, including the SMS settings
When activated, the dialer will disengage all other devices hooked up to the phone line. It will then, one by one, call all programmed
numbers and play the user recorded message which corresponds to the event. If the dialer makes a successful connection to a
programmed number, it will not call that number again. If the number is busy, the dialer will make 3 more attempts to call it. Empty tel.
number memories are skipped. If all memories are empty, the dialer is completely disabled. If the dialer is programmed to also
communicate with a monitoring station, the data will first be sent to the monitoring station..
Factory default setting: all telephone numbers are deleted.

JA-63 „PROFI“ Alarm System - 19 - MGK51404
12.2 Automatic SMS sending sequence: 7xxx....xxF5
If Jablotron’s SMS server service is provided in your country (check with your distributor), the following setting allows the
control panel to send alarm text messages (SMS) automatically to a desired mobile phone:
7 xx…x F9 yy....y F7 00F9 F7zz..z F5
where: xx…x = telephone number of the SMS server (check with your distributor if this
service is provided in your country)
F9 = separator (recognition of server’s reaction)
yy…y = mobile phone number (where the SMS should be sent to)
F7 = event code separator
00F9 = automatic event code – control panel will insert there a digital code
representing the alarm (depends on setting in section 12.4)
F7 = ID separator
zz..z = optional ID number which will be sent as a part of the SMS (ending). ID
distinguishes which alarm system sent the SMS). If ID is not required, do not
enter
F5 = storing of the sequence to memory 5 (32 digits can be stored to memory 5 as a
maximum - separators F9 and F7 takes only 1 digit each).
How the SMS server woks: when activated, the control panel dials the SMS server. After the connection is established, it sends
telephone number of the mobile phone, to which the SMS should be sent. Then the control panel specifies what happened by a digital
code and in the end the ID number is transferred (if programmed). In this moment the SMS server makes corresponding text message
and this message is sent to the GSM network.
Example: If SMS server number is 483559876, SMS should be sent to number 606123456 and ID number of the
installation is 41 enter : 7 483559876 F9 606123456 F7 00F9 F7 41 F5
Deleting of automatic SMS sending – to erase SMS sending enter:
7 F0 F5
Note: memory 5 can also be used to dial a Pager instead of SMS sending. To dial a Pager enter 7 xx..x F9 zzz....z F5 where xx..x is
number of the provider, zz…z is number of the pager and code of the message (check with a local Pager provider for details). Pause in
the dialing can be entered with F0, ∗ with F7 and # with F8. Pager dialing can be deleted with 7 F0 F5.
Factory default setting: SMS sending (Pager dialing) is erased.
12.3 Voice message(s) recording sequence: 8x
You can record two different voice messages (10 sec. each). Depending on the setting in section 12.4, a particular
message will be sent under different situations. Recording of the messages:
a) enter 85 on the keypad
b) press and hold push button on the X module
c) speak towards the module (max. 10 s)
d) release the button, message will play back
This results in the recording of message number 1. To record message 2 enter 86 in step a)
If you prefer sending only one, but longer, message (20 sec.), record message by entering 84 in step a). By
programming as described in section 12.4 you can specify which alarms will trigger the sending of a message.
Notes:
•Make the messages brief and clear. The dialer repeats the message to each called number for 40 seconds.
•The voice messages are stored in non-volatile memory and can be changed when ever you want to by repeating the above steps.
•The existing messages can be played by momentarily pressing the push button on the X module (or by entering F9 while in stand
by mode).
12.4 Triggering of voice and SMS messages sending sequences: 9 y x
With sequences 91x to 95x you can select which alarms will trigger the telephone dialer to call and what will be sent.
Enter:

JA-63 „PROFI“ Alarm System - 20 - MGK51404
9 y x where
Notes
•Final texts of alarm SMS are generated by the SMS server (providers computer) – based on the digital code sent by the alarm
system (check with provider for more details)
•If only one long voice message was recorded by using code 84 as described in section 12.3, then this message will be sent
when x=1 or x=2
•Voice messages are sent step by step to all telephone numbers programmed as described in section12.1
•SMS message is sent to a mobile phone number programmed as described in section 12.2
Example: if the dialer should send an SMS and voice message 1 when intruder or panic alarm is triggered, voice
message 2 in the case of fire and only an SMS in the case of technical alarm, enter: 911 921 932 943
Factory default setting: all alarms will trigger sending of voice message 1 and SMS (911, 921, 931, 941, 951).
12.5 Dialing method sequence: 9 0 x
Enter: 9 0 1 for tone dialing
9 0 0 for pulse dialing (this option is blocked for some countries)
Note: this dialing method setting is also valid for Central monitoring station communications.
Factory default: tone dialing
12.6 Telephone line checking sequence: 9 9 x
If this function is enabled, the dialer will check regularly if the telephone line is ready to make a phone call. If the line is
not ready for more than 15 minutes, the keypad will indicate a telephone line failure (failure L). A non-working telephone
line or a phone conversation or Internet connection longer than 15 minutes can cause a fault.
options: 9 9 1 checking enabled
9 9 0 checking disabled
Note: this setting is also valid when the dialer is used for Monitoring station communications as well as remote PC access
Factory default setting: checking disabled
12.7 Telephone dialer testing sequence: 8 9
After entering code 89 the dialer will call all programmed numbers and will play voice message 2. It will also send a
SMS message if programmed. The telephone line signals will be audible from the control panel’s built in speaker during
the test (if the dialer is triggered by an alarm in normal operation, it will call silently).
If you prefer testing with voice message 1 enter code 88.
Testing can be terminated with the N key.
13 To enable a remote computer to dial in
When the user or installer wants to dial in to the installation from their computer or a remote JA-60E keypad via a
JA-60U modem (see section 18), the following parameters should be programmed.
The most convenient programming is via a connected PC using the Comlink software (see 17). Programming can also be
performed manually:
•Enter the programming mode when disarmed (F 0 Service Code, factory default 6060), indicated by a ”P“
•Any unfinished programming sequence can be terminated by the Nkey.
•To exit the programming, press the N key (“P“ will turn off).
Dialing in parameters
Function sequence options
factory d.
Incoming call reaction 0 5 x 0=never, 1= second call, 2-6 =
after ring No. 2 - No.6 disabled
Remote access code (8 digits) 0 7 xxxxxxxx any 8 digits code 00000000
y Alarm
1 Panic – silent
2 Intruder
3 Fire
4 Tampering
5 Technical trouble
x reaction
0 no reaction
1 voice1 and SMS
2 voice 2 only
3 SMS only