John Lewis Skye 803/49101 User manual

Grey Double - Stock Code: 803/49101 Loch Blue Double - Stock Code: 803/49201
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Skye Bed
PRE-ASSEMBLY PREPARATION
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1
Thank you for purchasing this Skye Bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
(NOT INCLUDED)

A
B
C
D
E
F
G
H
I
J
M5 Allen Key x 1
M4 Allen Key x 1
Side Caps x 30
Centre Caps x 15
M8 X 35mm Bolt x 8 M6 X 25mm Bolt x 2
Screw 4 x 25mm x 2
M8 Spring Washer x 8
M8 Washer x 8
Screw 3.5 x 18mm x 4
Fitting and parts checklist
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 30
Centre Rail x 1
Legs x 4
Parts
Fittings
2

3
Step One
Step Two
H G
M8 Spring Washer x 8
M8 Washer x 8
E
M8 x 35mm x 8
Starting with the Headboard (1) attach the Side Rails (3) using the inserted M8 x 35mm Bolt (E), M8 Spring
Washer (G) and M8 Washer (H). Please do not tighten the bolts yet.Now attach the Footboard (2) to the Side Rails(3)
using M8 x 35mm Bolt (E), M8 Spring Washer (G) and M8 Washer (H). Do not tighten with M5 Allen Key (B) until you
have inserted the Centre Rail in the next step.
x2
Fig. 2
2
M8x35mm
3
M5(A)
(G)
(H)
Lower the Centre Rail (5) into the brackets in the centre of the Headboard (1) and Footboard (2) as shown in fig.3.
Now secure the Centre Rail (5) using M6 x 25mm Bolts (J) and tighten with M4 Allen Key (A) as shown in fig.4.
You can now tighten the bolts at the Side Rails from previous step (Step One) with the M5 Allen Key (B) so all
fastenings are now tightened.
M4 Allen Key M5 Allen Key
M6 x 25 x 2
J. A. B.
Centre Rail
F
i
g
.
3
51
2
And
M4(A)
M6 x 25(J)
F
i
g
.
4
5
1
2
And
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE RAILS
(FROM STEP ONE)
3
1
2
3
x2
1
3
M8(E)
M5(B)
(G)
(H)
2
3
1
3
Fig. 1
x2
1
3
M8x35mm
(G)
(H)
LOOSELY SECURE PARTS TOGETHER
IN ORDER FOR CENTRE RAIL
TO FIT IN NEXT STEP

(6) x 4
6.
Insert the Legs (6) into the pre-drilled holes on the underside of Headboard (1) and Footboard (2).
Twist the legs (6) to secure in place.
Step Four
Step Three
Next secure the bracket with Screw 3.5x18mm (I) on the Headboard (1) and Footboard (2) as shown
in fig. 5. Attach the metal clip on the Headboard (1) to the Side Rail (3) and make any adjustment needed.
Ensure all parts align together and secure with Screw 4x25mm (F) as shown in fig. 6.
IF
Screw
3.5 x 18mm x 4
4
Fig. 5
Fig. 6
Screw
4 x 25mm x 2
x2
2
3
(I)
x2
x2
13
3
3
1
3
(I)
1
2
3
6
3
6
x2
1
3
(F)
1
2

1
3
2
3
Step Six
Side Caps (30 pcs)
Centre Caps (15 pcs)
Slats (30pcs)
4.
C.
D.
5
Step Five
This bed is now ready to use.
4
4
C
D
D
With the curved side facing upwards, Insert 2 Slats (4) into a Centre Cap (C) followed by a Side Cap (D)
onto the other end of both Slats. Use your palms to push down the Side Caps into the Side Rails and
Centre Caps to the Centre Rail as shown in diagram below.
4
4
x15
Step 2
C
D
4
x30
Step 1

Care and Maintenance
Safety Instructions
This Skye bed should be cleaned using a soft damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural on-going discolouration
process.
Screws holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by competent adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
6
This product complies with BS EN 1725:1998.