John Lewis Twiggy Bed User manual

Twiggy Bed
MTO
Thank you for purchasing this Twiggy Bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
King
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/6
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact customer services on 01244 689949 or email
[email protected].
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
(NOT INCLUDED)

Side Caps x 16pcs
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 16
Centre Rail x 1
Legs x 4
Parts
7
Metal Plates x 4
8
Wide Slats x 16
Fittings and parts checklist
A
B
C
D
E
F
E
F
G
H
I
M5 Allen Key x 1pc
M4 Allen Key x 1pc
Wide Side Caps x 16pcs
Wide Centre Caps x 8pcs
Centre Caps x 8pcs
M6 X 25mm Bolt x 10pcs
M8 Spring Washer x 4pcs
Fittings
2/6
M13 Spanner x 1pc
M8 Nut x 4pcs
Screw 3.5 X 30mm x 4pcs

Place Metal Bracket on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2) and hand-tighten
to loosely secure parts together. Do not tighten bolts with M5 Allen Key (B) until you have inserted the Centre Rail
in the next step.
Step One
Step Two
Step by step assembly instructions
3/6
Lower the Centre Rail (6) into the brackets in the centre of the Headboard and Footboard as shown in fig.3. Now
secure the Centre Rail using M6 x 25mm Bolts (G) and tighten with M4 Allen Key (A) as shown in fig.4. You can
now tighten the bolts at the Side Rails from previous step (Step One) with the M5 Allen Key (B) so all fastenings are
now tightened.
M4 Allen Key
x 1 x 1
M5 Allen Key
x 1
M6 x 25mm x 2
G. A.A. B.
Centre Rail
F
i
g
.
3
6
1
2
And
M4 Allen Key(A)
M6 x 25mm (G)
F
i
g
.
4
6
1
2
And
Bracket
Side Rail
3
1
Bracket
Side Rail
2
3
Fig.1
Fig.2
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
NEXT STEP
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE RAILS
(FROM STEP ONE)
1
3
3
2
6

Step Three
G.
M8 Nut x 4
M13 Spanner x 1
Screw
3.5 x 30mm x 4 M6 x 25mm Bolt
x 8
Legs x 4
8.7.
Metal plates x 4
M8 Spring Washer
x 4
A.
M4 Allen Key x 1
x2
4/6
J.
I.K.
H.
For Headboard
M6 x 25mm (G)
2
8
M4 (A)
M6 x 25mm (G)
M6 x 25mm (G)
1
M4 (A)
M6 x 25mm (G)
8
3.5 x 30mm (J) 3.5 x 30mm (J)
M13 Spanner (K)
M8 Nut (I)
M8 Spring
Washer (H)
8
7
1
STEP 1
STEP 2
Attach the Metal Plate (8) to the bottom of Headboard and Footboard using Bolt M6 x 25mm (G)x2. Do not
tighten the bolt until you make adjustment for screw hole at Side Rail. Next, insert Screw 3.5 x 30mm (J) and tighten
the bolt using M4 Allen Key (A). Insert Leg (7) into the bottom of Metal Plate (8) using M8 Spring Washer (H)
and M8 Nut (I). Hold the M8 Nut (I) using M13 Spanner (K) and twist the Leg (7) to secure in place.
Repeat for the other 3 legs.
Yellow sticker
face down
AFTER INSERTING BOLT M6 x 25MM,
MAKE ADJUSTMENT FOR SCREW HOLE,
THEN INSERT THE SCREW 3.5 X 30MM.
THEN TIGHTEN THE BOLT AND SCREW
FIXINGS FULLY.
TWIST WOODEN LEG ONLY
WITHOUT MOVING THE M8 NUT,
SPRING WASHER AND SPANNER
3
3
3
For Footboard
Twist the wooden leg

2 Lines
Normal slats
2 Lines
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
D
F
4
5
(x8)
(x8)
4.
5.
C.
D
F.
E.
Side Caps x 16
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 16
Step Four
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x16). (Please note the Wide Slats must be inserted with the Wide Centre Caps (E) and Wide
Side Caps (F)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
4
4
C
E
5
5
Centre Caps x 8
E
F
F
D
D
4
4
5
5
C
Step Five
5/6
This bed is now ready to use.

Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call the customer
services helpline on 01244 689949 or email [email protected].
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This bed should be cleaned using a soft, damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
6/6