John Lewis 803/50402 User manual

John Lewis
Small double
Pre-assembly Preparation
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL PARTS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the John Lewis
Helpline on 01244 - 689949 or e-mail: [email protected]
Alpha Bedstead
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
Keep the support legs 5mm above the ground.
Thank you for purchasing this Alpha bedstead. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
For product support or spare parts
please call the John Lewis Helpline;
Tel: 01244 - 689949
e-mail:[email protected]
1/5
Stock number white: 803/50402
Stock number grey: 803/50201
Stock number white: 803/50404
Stock number grey: 803/50202
Double

Fittings and parts checklist
Bedstead Parts
12
3 4
5 6
7
Headboard x 1 Footboard x 1
Side Rails x 2 Wooden Slats x 28
Cross Bars x 2 Support Legs x 3
Centre Rail x 1
Fittings
AB
CD
EF
GH
Washer x 8 JCBC Bolt x 12
(M6 x 25 mm)
JCBC Bolt x 5
(M6 x 30 mm) M6 JCN Nut x 6
Adjuster x 3 Centre Stopper x 14
Side Stopper x 28 M4 Allen Key x 2
2/5

1
3
5
5
A
2
B
3
Step by step assembly instructions
Step One
Attach the Side Rails (3) to the Headboard (1) and Footboard (2) using Washer (A)
Repeat this for all 4 corners.
Step Two
and JCBC M6 x 25 mm Bolt (B). Tighten using Allen Key (H) as shown in the diagram below.
Place the Cross Bars (5) onto the Side Rails (3) and secure using JCBC M6 x 25 mm Bolt (B)
and M6 JCN Nut (D). Tighten using Allen Key (H) as shown below.
3/5

4/5
This bed is now ready to use.
7
6
4
E
H
C
D
H
C
F
G
Step Three
Ensuring the holes along the Centre Rail (7) are facing upwards, attach to the underside of the
Cross Bars (5) using M6 x 30 mm Bolt (C) and M6 Nut (D). Screw the Adjuster (E) fully into the bottom
of the Supporting Legs (6). Attach the Supporting Legs (6) into the pre-drilled holes on the underside
of the Centre Rail (7) using M6 x 30 mm Bolt (C) as shown in the below diagram.
Note: ,ylthgils)E(retsujdAehtwercsnu,ecalpniderucesera)6(sgeLgnitroppuSehtecnO
ensuring there is a 5mm gap between the Adjuster (E) and hard point of the floor.
Starting at the Headboard (1), attach the Centre Plastic Holders (F) into the holes along the Centre
Rail (7). Ensuring the Wooden Slats (4) are facing curved side up, place a Side Plastic Holder (G)
onto the end of the Wooden Slats (4). Insert the other end into the Centre Plastic Holder (F) then push
the end with the Side Plastic Holder (G) into the pre-drilled holes along the Side Rails (3). Repeat
this process for all the Wooden Slats (4).
Step Four

Care and Maintenance
Metal
This bedstead should be cleaned using a soft damp cloth and dried immediately. Do not use a very
wet cloth or allow any liquid contact for a long period of time as this can permanently damage
the surface.
Do not use abrasive cleaner or harsh detergents as this can damage the surface.
Do not drag any object across the bed as this can cause permanent damage.
Safety Instructions
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or
injury. Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent adult. No liability will be accepted for damage or injury caused by incorrectly installed or
assembled furniture. During assembly children should be kept away from the product due to
possible risk of injury.
Do not use this item if any components are missing or damaged.
This product complies with BS 1725:1998.
It is recommended that before moving heavy objects to a new location they are completely
dis-assembled to avoid personal injury or damage to the furniture. Please be careful to retain all
fittings when doing this.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 - 689949 or e-mail: [email protected]
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com
5/5