Johnson Controls PGP914 User manual

D-308495PGP914Rev.0
PGP914 Wireless PIR Motion Detector
Installation Guide
Installation guidelines
The reference to PGP914 throughout this manual includes the model PG9914.
CAUTION: Only qualified personnel may install this equipment. Place this device in non-
hazardous indoor locations only.
Important: Check the device andthe entire alarm system weekly to ensure optimal
performance.
Note: TocomplywithFCCandISEDCanadaRFexposurecompliancerequirements,locate
the device at a distance of at least 20 cm from all persons during normal operation. Do not
co-locate the antennas used for this product, or operate them in conjunction with any other
antenna or transmitter.
Figure 1: PGP914
Callout
Description
A
Lens
B
Battery pull-tab
C
Enroll button
D
Tamper switch
*D-308495*
D-308495

D-308495PGP914Rev.0
Figure 2: Optimizing detection and avoiding false alarms
For more information refer to About PGP914.
1. Do not install near high-voltage electrical lines.
2. Keep away from heat sources.
3. Do not install outdoors.
4. Avoid direct sunlight.
5. Do not expose to air drafts.
6. Do not install behindpartitions.
7. Do not mount on an unstable surface.
8. Install the device on a solid and stable surface at a height of 1.8 m to 2.4 m (6 ft. to 8 ft.)
Warning! Do not obscure partially or completely the device's field of view.
Enrolling the device
1. Refer to the control panel installation manual for the complete set of enrollment instructions
and testing procedures.
2. From the Installation menu, enter the Device enrollment menu and select the option to add
a new device.
3. Remove the battery pull-tab to power on the device and begin the auto-enrollment process.
If the battery pull-tab is not available or if the device does not automatically enroll, open the
device cover to trigger the enrollment. Alternatively, press the enroll button until the yellow
LED light turns on.
4. If requested, enter the PIN code printed on the device label.
5. To manually enroll the device:
a. Scan the QR Code on the device box, using the IQ4 camera if available, or see step b.
b. Manually enter the device ID, printed on the product label, in the format ID:125-xxxx.
Note: If the device has been powered up for more than 2 hours it will be identified by
the system only after the device has been reset.
The PGP914 is enrolled with device ID 125-XXXX. In fall back mode it enrolls as PGx914 with
device ID 126-XXXX.
6. Select the desired zone.
7. Configure any device parameters that are required.
8. Mount and test the device. See Local diagnostics test for information on testing the device.
Configuring the device parameters
1. Enter the DEVICE SETTINGS menu and follow the configuration instructions for the device as
described in the following table.
2 PGP914 Wireless PIR Motion Detector Installation Guide

D-308495PGP914Rev.0
Table 1: Configuration options
Option
Action
Alarm LED
Define whether the alarm LED indication will be activated.
Optional settings: LED ON (default) and LED OFF .
Event counter
Define whether an alarm will be activated upon continued
motion (low sensitivity) or upon a single alarm event (high
sensitivity).
Optional settings: LOW sensitivity (default) and HIGH
sensitivity.
Disarm activity
Define whether the device is active when the system is
disarmed.
Optional settings: NOT Active while disarmed (default), no
delay, 5 s delay, 15 s delay, 30 s delay, 1 min delay, 2 min
delay, 5 min delay, 10 min delay, 20 min delay and 60 min
delay.
VERY HOT > 35°C [>95°F]
Note: Feature not eval-
uated by UL/ULC
Define whether or not the control panel will report a very
hot alert when the temperature rises above the threshold
value for at least the Alert Delay duration value. Alert restore
will occur when the temperature drops 1°C (1.8°F) below the
threshold for at least the
Restore Delay duration.
Note: The default threshold value for very hot is 35°C
(95°F).
Optional settings: See Configuring the Temperature Alerts.
COLD < 19°C [<66°F]
Define whether or not the control panel reports a cold alert
when the temperature drops below the threshold value for at
least the Alert Delay duration. Alert restore occurs when the
temperature rises 1°C (1.8°F) above the threshold for at least
the
Restore Delay duration.
Note: The default threshold value for cold is 19°C (66°F).
Optional settings: See Configuring the Temperature Alerts.
PGP914 Wireless PIR Motion Detector Installation Guide 3

D-308495PGP914Rev.0
Table 1: Configuration options
Option
Action
FREEZING < 7°C [<45°F]
Define whether or not the control panel will report a freezer
alert when the temperature drops below the threshold value
for at least the
Alert Delay duration. Alert restore will occur
when the temperature rises 1°C (1.8°F) above the threshold
for at least the Restore Delay duration.
Note: The default threshold value for freezing is 7°C
(45°F).
Optional settings: See Configuring the Temperature Alerts.
FREEZER > -10°C [<14°F
Define whether or not the control panel will report a freezer
alert when the temperature rises above the threshold value
for at least the Alert Delay duration. Alert restore will occur
when the temperature drops 1 °C (1.8 °F) below threshold for
at least the
Restore Delay duration.
Note: Thedefault threshold value for freezer is -10°C
(14°F).
Optional settings: See Configuring the Temperature Alerts.
4 PGP914 Wireless PIR Motion Detector Installation Guide

D-308495PGP914Rev.0
Configuring the temperature alerts
You can configure the temperature alerts with the settings described in the following table.
Table 2: Temperature alert configuration options
Option
Action
Threshold
Displays the last saved threshold value and provides the
installer with the ability to change the value using the back or
next button.
Disable/Enable
Define whether the panel reports an alert or not.
Alert delay
Define the amount of time the panel waits before an alert is
reported when the temperature exceeds the defined default.
The alert delay time values are:
Immediately , 1 min , 2 min , 10
min
(default), 15 min , 20 min , 30 min .
Restore delay
Define the amount of time the panel waits before an alert is
reported when the temperature exceeds the defined default.
The restore delay time values are:
Immediately , 1 min , 2 min ,
10 min (default), 15 min , 20 min , 30 min .
Opening and closing the device cover
1. To open the device cover, loosen the cover screw located on the underside of the device. See
A1 in the following figure.
Figure 3: Device cover removal
2. Push in the tab on the underside of the device and pull the cover upwards. See A2 in the
previous figure.
3. To close the device cover, clip the cover onto the device base and tighten the cover screw.
PGP914 Wireless PIR Motion Detector Installation Guide 5

D-308495PGP914Rev.0
Figure 4: Closing the device cover
Installing the pet mask
Install the pet mask if you require pet immunity. For pet rejection, the optimal installation height is
2.1 m (7 ft.). Pet immunity is up to 38 kg (85 lb).
Note: Pet immunity is not supported at heights of 2.4 m (7.87 ft.) and above. Do not install the
pet mask if you are mounting the device at this height or above.
1. Insert the tabs at the base of the pet mask into the holes below the PIR sensor. See A1 in the
following figure.
2. Align the tabs on the sides of the pet mask with the holes on either side of the PIR sensor. See
A2 in the following figure.
3. Press down gently to install the pet mask.
Figure 5: Installing the Pet Mask
4. Close the device cover. See Figure 4.
6 PGP914 Wireless PIR Motion Detector Installation Guide

D-308495PGP914Rev.0
Removing the pet mask
Remove the pet mask if you do not require pet immunity.
1. Open the device cover. See Figure 3.
2. Remove the tabs at the sides of the pet mask from the holes on either side of the PIR sensor.
See A1 in the following figure.
3. Remove the tabs at the base of the pet mask from the holes below the PIR sensor. See A2 in
the following figure.
4. Gently lift the petmask.
Figure 6: Removing the Pet Mask
5. Close the device cover. See Figure 4.
Mounting the device using tape
1. Ensure the plug is attached to the back of the corner bracket. See Figure 9.
2. Peel the release liners off the two strips of double-sided adhesive tape and attach the tape to
the back of the bracket. See Figure 7. Use option A for flat surface mounting and B for corner
surface mounting.
PGP914 Wireless PIR Motion Detector Installation Guide 7

D-308495PGP914Rev.0
Figure 7: Double-sided adhesive tape placement on the bracket
3. Mount the bracket on the wall. For flat bracket see Figure 8. For corner bracket see Figure 11.
4. Align the device with the bracket. See A1 in the figure below.
5. Slide the device upward until a click is heard. See A2 and A3 in the figure below.
Figure 8: Attaching the device to the bracket
Mounting the device using screws
About this task:
Note: Mounting using screws is required for UL/ULC commercial burglary and residential fire
type installations. Wall tamper (break-away segment) shall also be enabled.
1. Screw the bracket onto the wall.
Note:
Make sure to fasten the break-away segment to the frame. If the device is forcibly
removed from the wall, this segment will break away from the base, causing the tamper
switch to open.
8 PGP914 Wireless PIR Motion Detector Installation Guide

D-308495PGP914Rev.0
Wall tamper is required for UL/ULC commercial burglary and residential fire installations.
a. To mount the bracket on a flat surface, screw the mounting bracket to the wall. See A in
the following figure.
Figure 9: Flat bracket screw installation
b. Ensure the corner bracket plug is attached. See B in the following figure. To mount
the bracket on a corner see C or D in the figure below. C is for without back tamper
protection, and D is for with back tamper protection.
Figure 10: Corner bracket screw installation
Callout
Component
A
Flat surface mounting
B
Corner bracket with plug
C
Corner bracket with back tamper
D
Corner bracket without back tamper
E
Stopper snap
F
Break-away segment
2. Align the device with the bracket. See A1 in the following figure.
3. Slide the device upward until a click is heard. See A2 and A3 in the following figure.
PGP914 Wireless PIR Motion Detector Installation Guide 9

D-308495PGP914Rev.0
Figure 11: Attaching the device to the corner bracket
Disassembling the device from the bracket
1. Open the device cover. See Figure 3.
2. Remove the battery.
3. Use a screwdriver to press on the stopper snap to release the device base from the bracket.
See A1 in the following figure.
4. Slide the device downwards to remove it from the bracket. See A2 in the following figure.
Figure 12: Disassembling the device from the bracket
Replacing the battery
Note: The device transmits a low battery signal upon detection of low voltage. It is
recommended to wait about 1 minute after battery removal before inserting the new battery.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the manufacturer's instructions and according to local rules and
regulations.
1. Remove the device cover. See Figure 3.
2. Remove the battery. See A in the following figure.
3. Insert the new battery while observing battery polarity. See B in the following figure.
10 PGP914 Wireless PIR Motion Detector Installation Guide