Johnson Controls LC-200S User manual

Installation InstructionsLC-200S
1
ISTISJCELC200S 0.0
2012/19/EU
LC-200S
IR DETECTOR
1. INTRODUCTION
LC-200S is the detector for all security installations needing an excellent product that is easy to install, suitable for any residential installation and does not
require special attention for programming. No special care is required for the detector. It can simply be installed and turned on.
LC-200S detectors are equipped with lenses designed by Johnson Controls and are manufactured by Fresnel Technologies, Inc.
LODIFF®optic creation technology combined with POLY IR®materials make it a product of the highest quality and efficiency.
LC-200S detector is pet immune (feature not evaluated by UL/ULC) and has a 12 m (40 ft) range at a 100-degree angle.
2. INSTALLATION
- Using a thin screwdriver, loosen the bottom screw and open the cover (see Fig 1)
- Remove the board from the base by levering the ABS cover (see Fig 2)
- Drill the stopper on the base of the cover at the desired fastening location (or use the optional swivel that is not IMQ certified)
- Recommended height is 2.1 m
- Slide the cable in through the back slot and out the top hole
- Wire the terminals following the connections shown in “Connection and Setup” - Fig 1 -
- Fig 2 -
Ultraviolet Stabilization
POLY IR®4 Lens Material
The lens is printed with POLY IR®material.
This materials offers a better combination of
transmittance, environmental stability and color
than any other polymer on the market. Materials
are available for the 8-14 micron infrared region.
LODIFF®and POLY IR®are registered trademarks of
Fresnel Technologies, Inc.
LODIFF®Fresnel Lens Technology
This lens series is made by tiling LODIFF®lens pieces.
These lenses offer significantly improved performance
over the typical constant-bandwidth Fresnel lens.
LODIFF®and POLY IR®are registered trademarks of
Fresnel Technologies, Inc.
High RFI Protection
The detector has very high RFI immunity due to
the complete lack of traditional amplifiers.
White Light Protection
The detector digitally filters white light
components.
Pet Immunity
Thanks to a new lens design and the digital analysis
system, all of our detectors are immune to pets
weighing up to 15 kg.
Digital Signal Analysis
This detector is equipped with a traditional PIR with
a processor that converts the analysis into digital
format for optimum performance in all situations.
NOTE: Do not partially or completely cover the detector's field of vision
NOTE: the pet function is not IMQ certified
PULSE
jumper
LED
jumper
T-A-EOL
jumpers

Installation InstructionsLC-200S
2
ISTISJCELC200S 0.0
3. CONNECTION AND SETUP
Jumper PULSE: closed = 2 pulses; open = 1 pulse
Jumper LED: closed = LED ON; open = LED OFF
Jumpers T - A - EOL open = NC contacts without resistors (not for UL/ULC applications)
Jumpers T - A - EOL closed = DEOL supervision with internal resistors
SUPPLY: power supply 9-15 VDC / 25 mA. Note: For UL/ULC installations the detector shall be provided with minimum of 4 hours of standby power from either
a listed compatible control unit or power supply. Use only resistive loads on the outputs.
Installation must be carried out by trained personnel according to professional standards.
The manufacturer accepts no responsibility if the product is tampered with by unauthorized persons.
The alarm system should be checked for proper operation at least once a month. However, a reliable electronic alarm system does not prevent intrusion, robbery, fire or
anything else but merely decreases the risk of such situations occurring.
LC-200S complies with requirements EN 50131-2-2 Grade 2, EN 50131-2-2 Class II
Technical Characteristics
RANGE 12 m (40 ft)
HORIZONTAL COVERAGE 100°
LENSES LODIFF®Fresnel Lens
POLY IR®4 material
LED blue
ALARM DURATION 2 s
SELF-DIAGNOSTICS -
LED WALK TEST YES
MICROWAVE FREQUENCY -
SOLID STATE RELAY YES
EOL RESISTANCE YES
CREEP ZONE DEVICE YES
CASE TAMPER YES
BACK TAMPER NO
ANTI-MASKING -
PULSE COUNTER YES
RFI PROTECTION 30 V/m
HEAT COMPENSATION YES
FULLY DIGITAL YES
SWIVEL OPTION YES
POWER SUPPLY 9-15 VDC / 25 mA
COVER MATERIAL ABS
PET IMMUNITY YES
OPERATING TEMPERATURE
-10°C to +40°C
UL/ULC tested: 0°C to 49°C
HUMIDITY 93% RH
DIMENSIONS 114 x 63 x 40 mm
DEOL supervision
(internal resistors/closed jumpers)
DEOL supervision
(external resistors/open jumpers)
NC (no EOL supervision/
open jumpers)
Not used on UL/ULC
listed installations
101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. [phone], FAX:[phone]
fresnel technologies inc.
2003
SIDE VIEW:
2.1m
(6.8ft)
TOP VIEW:
10m
(33ft)
(50ft)
15m
FRONT VIEW:
(50ft)
15m
5m
(16ft)
jay
WP 0.9 GI 6 T1
PET IMMUNE ARRAY
(28.2ft)
8.6m
(15.7ft)
4.8m
(6.8ft)
2.1m
35.6mm
(1.4 in)
49.8 mm
(1.96 in)
12.5 mm
(0.49 in)
95°
5m
(16ft)
10m
(33ft)
(50ft)
15m
0
Figure 7
101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. [phone], FAX:[phone]
fresnel technologies inc.
2003
SIDE VIEW:
2.1m
(6.8ft)
TOP VIEW:
10m
(33ft)
(50ft)
15m
FRONT VIEW:
(50ft)
15m
5m
(16ft)
jay
WP 0.9 GI 6 T1
PET IMMUNE ARRAY
(28.2ft)
8.6m
(15.7ft)
4.8m
(6.8ft)
2.1m
35.6mm
(1.4 in)
49.8 mm
(1.96 in)
12.5 mm
(0.49 in)
95°
5m
(16ft)
10m
(33ft)
(50ft)
15m
0
Figure 7
10m
(33ft)
5m
(16ft)
5m
(16ft)
10m
(33ft)
2.1m
(6.8ft)
2.1m
(6.8ft)
4.8m
(15.7ft)
8.6m
(28.2ft)
12m
(40ft)
SIDE VIEW:
0
Zx COM
–
+
EOL
SUPPLY ALARM TAMPER
–
+EOL
TAMPER
LC-200S
EOL
A
T
All 3 jumpers open
Negative connected tamper
Panel
Zx COM
–
+
EOL
A
T
EOL
SUPPLY ALARM TAMPER
–
+EOL
TAMPER
LC-200S
COM
NC / NO TAMPER
All 3 jumpers closed
Zone ok = 5.6 kohm
Zone in alarm = 5.6 kohm + 5.6 kohm
Tamper zones = open or short circuit
Negative connected tamper
Panel
5.6 kohm 5.6 kohm
Zx COM
–
+
EOL
SUPPLY ALARM TAMPER
–
+EOL
TAMPER
LC-200S
EOL
A
T
All 3 jumpers open
Negative connected tamper
Panel
5.6 kohm
5.6 kohm

Installation InstructionsLC-200S
3
ISTISJCELC200S 0.0
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
– Consult the dealer or an experienced radio/TV technician for help.
Warning! Changes or modifications to this equipment not expressly approved by the party responsible for compliance (Tyco Safety Products Canada Ltd.) could void the
user’s authority to operate the equipment.
This device complies with part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference and (2) This
device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la classe B est conforme a la norme NMB-003 du Canada.
© 2022 Johnson Controls. All rights reserved. JOHNSON CONTROLS is a registered trademark. Unauthorized use is strictly prohibited.