J+J S2 User manual

www.jjbcn.com
HANDBOOK
J.J. BCN INTERNACIONAL, S.A.

INDEX
01. Actuator Part List
·S2, S6, S10, B2, B6, B10 ·
·S25, S40, B25, B40
02. J4M Series
· Voltage
· Electrical Connectors
· ID Actuator Label
· Local Visual Posion Indicator
· Emergency Manual Override Facility
· External connecng Diagram
03. Datasheet
· J4M 2
· J4M 6
· J4M 10
· J4M 25
· J4M 40
04. Bluetooth interface manual
05. Opon
· Modbus
06. Guarantee
07. Contact
HANDBOOK

01 ACTUATOR PART LIST
HANDBOOK_ACTUATOR PART LIST 03
INDEX
MODELS: S2, S6, S10, B2, B6, B10
Posion indicator
Automac-manual lever
visual control of operaon
ISO mulflange
Power supply plug
Volt free contact plug
Signal plug
Manual override

INDEX
HANDBOOK_ACTUATOR PART LIST 04
MODELS: S25, S40, B25, B40
Posion indicator
Volt free contact plug
visual control of operaon
Power supply plug
ISO mulflange Automac-manual lever
Signal plug
Manual override

02 J4M SERIES
HANDBOOK_J4M SERIES 05
INDEX
J4M Electric actuators operate with the use of live electricity. It is recommended that only qualified
electrical engineers be allowed to connect or adjust these actuators.
READ THESE INSTRUCTIONS BEFORE CONNECTING THE ACTUATOR. DAMAGE CAUSED BY
NON COMPLIANCE OF THESE INSTRUCTIONS IS NOT COVERED BY OUR WARRANTY.
Warning: Ensure that the square rubber seal is in place when fixing each
DIN plug to the actuator. Failure to do so could allow water ingress and
damage caused by this installaon error will invalidate any warranty. The
DIN plugs are fixed to their respecve bases on the actuator housing with
a screw. Do not over ght the screw (8) when assembling (Max. 0.5Nm ).
1. Gasket
2. Terminal strip
3. Cable fixing screws
4. Housing
5. Washer
J4M 2 to 40
6. Grommet
7. Gland - nut
8. Fixing screw
9. Washer
10. Gasket
All our actuators model S2 to S40 are ready to work from 24-240 VDC/VAC.
All our actuators model B2 to B40 are ready to work at 12 VDC/VAC ONLY.
VOLTAGE TO BE CONNECTED
Warning: Before connecng ensure that the voltage to be applied to the actuator is within the range
shown on the idenficaon label. The supplied electrical connectors, used to connect to the actuator
are DIN plugs. Ensure the diameter of cable to be used conforms to the maximum and minimum
requirements of the DIN plugs to maintain water ghtness (Fig.1).
ELECTRICAL CONNECTORS

_04
HANDBOOK_J4M SERIES 06
INDEX
ID ACTUATOR LABEL
1 - Actuator Model.
2 - Voltage to be connected.
3 - Time/Turn.
4 - Actuator ready to bear between –20ºC
& + 70ºC.
5 - Plate to fix the valve to the actuator,
following ISO 5211.
6 - Female output drive size, following DIN3337.
7 - Maximum Operaonal torque.
8 - Actuator serial number.
9 - Bar code of the serial number.
10 - Actuator Series.
11 - Max. Number Turns.
12 - Duty: 75%.
13 - Actuator with the IP67 protecon.
14 - Actuator with the CE cerficate.
Actuator with the UKCA marking.
15 - Quality Control Conformity .
16 - QR code for manufacturing.
17 - DPS configuraon.
10
11
12
14
13
15
16
1
2
3
4
5
6
8
9
17
7

HANDBOOK_J4M SERIES 07
INDEX
LOCAL VISUAL POSITION INDICATOR
EMERGENCY MANUAL OVERRIDE FACILITY:
All J4M actuators are supplied with a local visual posion indicator (Fig.6).
The OPEN posion shows the indicator in BLACK and at the end of the stroke (max 14 turns) shows
the full indicator in RED.
The J4M has 2 operang modes, automac and manual, the required mode is selected by
using a lever on the lower half of the actuator housing (Fig 7).
Warning: Do not remove the selector lever securing screw, as this will allow its internal mechanism
to become loose and will cause irreparable damage to the actuator’s gearbox.
Removing this screw will invalidate the warranty.
When “AUTO” posion is selected:
The hand wheel rotates automacally, it is very important not to block it, otherwise the actuator
could suffer unrepairable damages.
The 2 posions are marked:
AUTO = Automac operaon
MAN = Manual operaon
Fig. 6 OPEN Fig. 6 MAX. 14 TURNS

HANDBOOK_J4M SERIES 08
INDEX
When “MAN” funcon is selected:
1 - The electronic system cuts the power to the motor aer a few minutes.
2 - The mechanical connecon between the motor and the output sha is disconnected.
3 - The desired posion can be achieved by using the hand wheel.
4 - There are two ways to re-acve the motor aer being isolated whilst in “MAN” posion:
a) Change from “MAN” mode to “AUTO”. Deacvate the supply voltage for a few seconds.
which resets the actuator and it could operate automacally again.
Fig. 7 J4M 2,6 and 10 Fig. 7 J4M 25 and 40
J4M 2, 6 and 10
Hand Wheel
J4M 25 and 40
Posion Indicator
Automac - Manual
and

HANDBOOK_ELECTRICAL DIAGRAMS 09
INDEX
ELECTRICAL DIAGRAMS J4M
J4M 25/40
[Capte la
A
B
J4M 2/10
A
B
3 WIRES ON-OFF
J4M 2/10
[Capte la
B
A
J4M 25/40
[Capte la
A
B
2 WIRES ON-OFF
J4M 2/10
A
B
J4M 25/40
A
B
C
POSITIONER

INDEX
HANDBOOK_ELECTRICAL DIAGRAMS 10
ELECTRICAL DIAGRAMS J4M
POSITIONER
ONLY OU
TPUT
J4M 2/10
A
B
C
J4M 25/40
A
B
C
A= Power supply plug
A: VAC 3 WIRES (Grey plug)
PIN1 = NEUTRAL + PIN 2 = Close
PIN1 = NEUTRAL + PIN 3 = Open
PIN1 = NEUTRAL + PIN2+PIN3 = STOP
A: VDC 3 WIRES (Grey plug)
PIN1 = NEGATIVE + PIN 2 = POSITIVE = Close
PIN1 = NEGATIVE + PIN 3 = POSITIVE = Open
PIN1 = NEGATIVE + PIN 2+3 = POSITIVE = Stop
B: Volt free contact, plug
PIN1 / PIN 2 = Close
PIN1 / PIN 3 = Open
C: Instrumentaon Signal
PIN1 = (-) Negave + PIN 3 = (+)Posive =
Output signal

INDEX
03 Datasheet - J4M 2
24-240 VDC/VAC 12 VDC/VAC ONLY
MATERIAL:
Body: Ancorrosive Polyamide, Grey colour / Oponal: Polypropilene V0, Black colour.
Cover: Ancorrosive Polyamide, Red colour / Oponal: Polypropilene V0, Natural colour.
Output drive: Zamak, Zinc plated / Oponal: Zamak, TEFLON coated
Flange: ZamaK and Zinc plated / Oponal: Zamak and TEFLON coated.
Main external sha: Ancorrosive Polyamide
External screws: Stainless Steel
Gears: Steel and Polyamide
Visual posion indicator: Polyamide
Dome: Polycarbonate
Note: Technical data are the same despite the different casings.
Electronic Torque Limiter funcon
Electric motor: 24VDC Brushless motor
Insulaon: Class B
(IEC 60034) Service: S4
GENERAL CHARACTERISTICS
HANDBOOK_DATASHEET - J4M 2 _11
4 secs/360º
Maximum number turns
Confirmaons
5,5Nm/48,68lb/in
Maximum operaonal torque
Minimum operaonal torque 2Nm/17,70lb/in
2 relays (Max. 24V/1A. Open and Close)
1,9 Kg
14
5210
MANUFACTURER OPTION

J4M 2 SIZES
HANDBOOK_DATASHEET - J4M 2 _12
INDEX

Datasheet - J4M 6
24-240 VDC/VAC 12 VDC/VAC ONLY
HANDBOOK_DATASHEET - J4M 6 _13
INDEX
GENERAL CHARACTERISTICS
MATERIAL:
Body: Ancorrosive Polyamide, Grey colour / Oponal: Polypropilene V0, Black colour.
Cover: Ancorrosive Polyamide, Red colour / Oponal: Polypropilene V0, Natural colour.
Output drive: Zamak, Zinc plated / Oponal: Zamak, TEFLON coated
Flange: ZamaK and Zinc plated / Oponal: Zamak and TEFLON coated.
Main external sha: Stainless Steel
External screws: Stainless Steel
Gears: Steel and Polyamide
Visual posion indicator: Polyamide
Dome: Polycarbonate
Note: Technical data are the same despite the different casings.
Electronic Torque Limiter funcon
Electric motor: 24VDC Brushless motor
Insulaon: Class B
(IEC 60034) Service: S4
S6
S6 / B6
B6
Minimum operaonal torque
Maximum number turns
Confirmaons
3 Secs/360º
Maximum operaonal torque 9Nm/79,66lb/in
5Nm/44,25lb/in
2 relays (Max. 24V/1A. Open and Close)
1,9 Kg
14
MANUFACTURER OPTION

J4M 6 SIZES
HANDBOOK_DATASHEET - J4M 6 _14
INDEX

Datasheet - J4M 10
GENERAL CHARACTERISTICS
24-240 VDC/VAC 12 VDC/VAC ONLY
INDEX
MATERIAL:
Body: Ancorrosive Polyamide, Grey colour / Oponal: Polypropilene V0, Black colour.
Cover: Ancorrosive Polyamide, Red colour / Oponal: Polypropilene V0, Natural colour.
Output drive: Zamak, Zinc plated / Oponal: Zamak, TEFLON coated
Flange: Aluminum and Cataphoresis / Oponal: Aluminum and TEFLON coated.
Main external sha: Stainless Steel
External screws: Stainless Steel
Gears: Steel and Polyamide
Visual posion indicator: Polyamide
Dome: Polycarbonate
Note: Technical data are the same despite the different casings.
Electronic Torque Limiter funcon
Electric motor: 24VDC Brushless motor
Insulaon: Class B
(IEC 60034) Service: S4
HANDBOOK_DATASHEET - J4M 10 _15
S10
S10 / B10
B10
Maximum number turns
Confirmaons
12,8 Secs/360º
Maximum operaonal torque 15Nm/ 132,76 lb/in
Minimum operaonal torque 7Nm/61,96 lb/in
2 relays (Max. 24V/1A. Open and Close)
1,9 Kg
14
MANUFACTURER OPTION

J4M 10 SIZES
HANDBOOK_DATASHEET - J4M 10 _16
INDEX

Datasheet - J4M 25
GENERAL CHARACTERISTICS
24-240 VDC/VAC 12 VDC/VAC ONLY
INDEX
MATERIAL:
Body: Ancorrosive Polyamide, Grey colour / Oponal: Polypropilene V0, Black colour.
Cover: Ancorrosive Polyamide, Red colour / Oponal: Polypropilene V0, Natural colour.
Output drive: Zamak, Zinc plated / Oponal: Zamak, TEFLON coated
Flange: Aluminum and Cataphoresis / Oponal: Aluminum and TEFLON coated.
Main external sha: Stainless Steel
External screws: Stainless Steel
Gears: Steel and Polyamide
Visual posion indicator: Polyamide
Dome: Polycarbonate
Electronic Torque Limiter funcon
Electric motor: 24VDC Brushless motor
Insulaon: Class B
(IEC 60034) Service: S4
Note: Technical data are the same despite the different casings.
S25
S25 / B25
B25
Maximum number turns
Confirmaons
9,3 Secs/360ª
Maximum operaonal torque 30Nm /265,52 lb/in
Minimum operaonal torque 10Nm / 88,51 lb/in
2 relays (Max. 24V/1A. Open and Close)
3.8 Kg
Standard *17 Oponal *11 and *14
F05/F07
14
HANDBOOK_DATASHEET - J4M 25_17
MANUFACTURER OPTION

J4M 25 SIZES
INDEX
HANDBOOK_DATASHEET - J4M 25_18

Datasheet - J4M 40
GENERAL CHARACTERISTICS
INDEX
24-240 VDC/VAC 12 VDC/VAC ONLY
MATERIAL:
Body: Ancorrosive Polyamide, Grey colour / Oponal: Polypropilene V0, Black colour.
Cover: Ancorrosive Polyamide, Red colour / Oponal: Polypropilene V0, Natural colour.
Output drive: Zamak, Zinc plated / Oponal: Zamak, TEFLON coated
Flange: Aluminum and Cataphoresis / Oponal: Aluminum and TEFLON coated.
Main external sha: Stainless Steel
External screws: Stainless Steel
Gears: Steel and Polyamide
Visual posion indicator: Polyamide
Dome: Polycarbonate
Electronic Torque Limiter funcon
Electric motor: 24VDC Brushless motor
Insulaon: Class B
(IEC 60034) Service: S4
Note: Technical data are the same despite the different casings.
S40
S40 / B40
B40
Maximum number turns
Confirmaons
12 Secs/360º
Maximum operaonal torque 50Nm / 422,54 lb/in
Minimum operaonal torque 16Nm /141,61 lb/in
2 relays (Max. 24V/1A. Open and Close)
3.8 Kg
Standard *17 Oponal *11 and *14
F05/F07
14
HANDBOOK_DATASHEET - J4M 40_19
MANUFACTURER OPTION

J4M 40 SIZES
INDEX
HANDBOOK_DATASHEET - J4M 40_20