Jung 5232 Series User manual

Blinds Management Standard attachment with sensor input
Ref.-no.: ..5232,..5232 S
Stand: Feb-08 325 507 13
Operating instructions
Standard attachment
Standard attachment with sensor input
1. Safety warnings
Attention: Electrical equipment must be installed and fitted by
qualified electricians only. Failure to observe the warnings may
cause damage to the device and result in fire or other hazards. To
prevent electric shocks, disconnect the mains supply (by cutting
out the circuit breaker) before working on the device or on the load.
The blind/shutter management system JM has been developed for
the control of window blinds and window shutters. Do not switch
other loads. Using the device for other applications such as the
control of roller-shutter doors may involve hazards. These hazards
must be excluded by the user by taking appropriate safety
measures (e.g. light barriers). Observe also the safety warnings set
out in the operating instructions of the respective motor control
insert used.
2. Function
The standard attachment is a component of the blind/ shutter
management system JM and can only be used in conjunction with the
motor control insert. A press on the  button raises the blind/shutter
while a press on the  button lowers the blind/shutter. The moving time
of the blind/shutter can be individually programmed between 0.5 seconds
and 2 minutes (preset value = 2 minutes). The attachment is additionally
equipped with an anti-lockout function to prevent any inadvertent
automatic lowering of the blind/shutter

Blinds Management Standard attachment with sensor input
Ref.-no.: ..5232,..5232 S
2
3. Operation
Brief press on the button (less than 1 second):
A pulse corresponding in length to the duration of the press is generated.
This function is used for the adjustment of the slats of blinds/shutters or
for stopping the blind/shutter in the continuous run mode.
Long press on the button
(longer than 1 second):
The blind/shutter control switches over to selfmaintained operation
(‘Continuos run“).
Anti-lockout function
(press on  longer than 4 seconds):
The LED in the middle of the attachment is lit up. The shutter moves to
the upper limit stop and the antilockout function is active. Commands
from the central unit, extension units and the sensors are disregarded.
The anti-lockout function is deactivated by a press on the button  or
after a mains failure.
„Programming“ the individual moving time
If shutter is to be prevented from moving down completely to the lower
limit position („ventilation function“) or when an outdoor sensor is used, a
shorter moving time can be programmed.
1. Actiivating the programming mode:
•Press center of button (longer than 4 s) until the LED in middle of
the attachment flashes. The shutter moves automatically to the
upper limit stop.
2. Programming the moving time:
•Keep the button depressed towards the  symbol until the shutter
is in the positiobn to be programmed. The shutter stops as soon as
the button is released
3. Storing or rejecting the moving time:
• Press the center of the button (at least 1 s) to store the individual
moving time.
• Press the  or the  symbol of the button to reject the moving
time.
The programming mode ends automatically and the LED is extinguished.
The individual moving time remains stored permanently. The old moving
time is replaced by a newly programmed time. To execute the
programmed moving time, the blind/ shutter must be moved in the
„continuous mode“ up to the upper limit position.
4. Fitting
The standard attachment is installed together with a motor control insert
(Art. no. 230 ME, 232 ME, 220 ME, 224 ME) in a flush-mounting box in
acc. with DIN 49073 (deep box recommended).

Blinds Management Standard attachment with sensor input
Ref.-no.: ..5232,..5232 S
3
The connecting terminals of the insert must be at the bottom. Description,
fitting and connection of the insert: see separate instructions. Plug the
standard attachment (2) together with frame (3) onto the insert (1). The
electrical contact is established via connectors (4) and (5).
Important:
When using sensors, observe the fitting information set out in the
instructions of the respective motor control insert.
4.1. Standard attachment with sensor input:
Sun protection function:
A sun sensor permits automatic lowering of the blind/ shutter in strong
sunshine. To execute this function, the blind/shutter must be raised in the
„continuous mode“ to the upper limit position. The attachment activates
the sun protection function after 2 minutes. Any manual operation
deactivates the sun protection function. The sun protection function
begins ca. 2 minutes after the preset brightness level has been exceeded
(level presettable ca. 5.000 - 80.000 lux) and the blind/ shutter moves
down. When the ambient brightness has been below the preset threshold
for at least 15 minutes, the blind/ shutter is raised again (short brightness
variations have no effect). The attachment distinguishes between an
inside or outside sun sensor. To determine the type of sensor installed,
the blind/ shutter performs an initialization move when the sun protection
function is activated for the first time. The sensor installed is identified as
an outside sensor, if no shading of the sensor is detected. Otherwise, the
sensor is an inside type.
Sun sensor on the inside:
The sun sensor is installed on the window pane. The installation height
on the pane determines the position to which the blind/shutter moves
when the brightness threshold is exceeded.
Sun sensor on the ouitside:
After the initialization move, the blind/shutter is raised again and then
lowered again with the individual moving time. From now on, the
attachment always executes the individual moving time when in the sun
protection mode.
With glas breakage sensor:
The glass breakage sensor is attached to the window pane. When the
pane breaks, the shutter moves down to the lower limit stop. Application:
protection against the weather in the event of glass breakage. The glass
breakage message is reset by pressing the  button and the shutter
moves up again.

Blinds Management Standard attachment with sensor input
Ref.-no.: ..5232,..5232 S
4
Important:
When the lock-out protection is active, the signal from the glass breakage
sensor is disregarded.
Glass breakage sensors must not be used in combination with the
wind sensor. The wind protection function via the extension input
 (shutter moving up) is disabled after a glass breakage. The blind
or shutter remains closed.
Setting the brightness threshold for the standard attachment with
sensor input
The brightness level at which the shutter is to be lowered can be adjusted
with potentiometer (6) at the back of the standard attachment within a
range of ca. 5.000 to 80.000 lux.
setting ☼ca. 80000 Lux
setting ☼ca. 5000 Lux
The potentiometer is factory-adjusted to a value of ca. 15.000 lux
(position as shown in fig. B).
5. Technical Data
Connection: by plugging onto the
motor control insert
Moving time: 0.5 to 120 seconds
Moving time tolerance: +/- 0.5 seconds
Switch-over time: 1 second
Ambient temperature: 0 to +45 °C
Storage temperature: -10 °C to +60 °C
Brightness
setting range: ca. 5.000 to 80.000 lux
(sensor model only)

Blinds Management Standard attachment with sensor input
Ref.-no.: ..5232,..5232 S
5
6. Acceptance of guarentee
We accept the guarantee in accordance with the corresponding legal
provisions.
Please return the unit postage paid to our central service
department giving a brief description of the fault:
ALBRECHT JUNG GMBH & CO. KG
Service-Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +(49) 23 55 . 80 65 51
Telefax: +(49) 23 55 . 80 61 89
E-Mail: [email protected]
General equipment
Service-Line: +(49) 23 55 . 80 65 55
Telefax: +(49) 23 55 . 80 62 55
E-Mail: [email protected]
KNX equipment
Service-Line: +(49) 23 55 . 80 65 56
Telefax: +(49) 23 55 . 80 62 55
E-Mail: [email protected]
The -Sign is a free trade sign addressed exclusively to the
authorities and does not include any warranty of any properties.