Kabuto KAMUI User manual

1205342_Kabuto Engels.indd 1 13-07-17:JPN
Instruction Manual
Manuel d’utilisation / Gebrauchsanweisung
Manuale d’istruzioni Indice / Manual de instrucciones
Handleiding / Bruksanvisning
Instrukcja obsługi / Instruktionsmanual
Εγχειρίδιο χρήσης / Manual de instruções
Käyttöopas / 取扱説明書

ENG
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 1 18-07-12 14:26

ENG 1
ENG
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner (Main body, chin area)
●Chinstraps including One-touch buckle
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
a0Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap
Covers•••••P-21
Cleaning of Interiors •••••P-21
aa Remove/Replace Wind Shutter-2•••••P-22
as Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner (Main body, chin area)
●Chinstraps including One-touch buckle
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
a0Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap
Covers•••••P-21
Cleaning of Interiors •••••P-21
aa Remove/Replace Wind Shutter-2•••••P-22
as Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 1 20-07-12 13:31

ENG
ENG 2
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 2 13-07-12 09:53

ENG 3
ENG
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 3 13-07-12 09:53

ENG
ENG 4
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 4 13-07-12 09:53

ENG 5
ENG
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 5 13-07-12 09:53

ENG
ENG 6
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 6 13-07-12 09:53

ENG 7
ENG
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 7 13-07-12 09:53

ENG
ENG 8
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
When the chinstrap covers of KAMUI helmet become dirty, they may be washed after
detaching them from the chinstraps.
–DETACHING–
aUndo the hook and loop fastener at the end of each chinstrap.
bPull the chinstrap cover from the chinstrap to detach it.
–ATTACHING–
aIn the reverse order of detaching (Pay attention to the direction of the chinstrap
cover), let the chinstrap go through from the upper portion of the chinstrap cover.
bFinally, fasten the snap.
Remove/Replace Chinstrap covers1
Please pay attention to the side of the chinstrap covers.
The side where your chin touches is the back.
CAUTION!
The inner pad, the cheek pads and the chinstrap covers of this helmet are all
washable. Please wash them by hand or washing machine (must use a washing
net) with mild soap or diluted detergent. Dry them in the ventilated area after
washing. Please refer to page 21 for more details.
Fully-washable interiors
Chinstrap Chinstrap
Chinstrap
Chinstrap
cover
Chinstrap
cover
Attaching
hole
Attaching
hole
Put on
Pull off
Put on
Pull off
2Fastening Chinstraps
WARNING!
Be sure to adjust the length of the chinstraps of the helmet properly.
Otherwise, your helmet may drop off or choke your neck in case of an
accident while riding. Chinstraps play a very important role. Thus, please
adjust the chinstraps of your helmet properly and securely before riding.
One-touch buckle
One-touch buckle makes it easy to take
on and off your helmet.
WARNING!
Be sure to fasten the One-touch
buckle securely before riding. If the
One-touch buckle is not fastened or
not fastened securely, your helmet
may drop off in case of an accident
or when falling down while riding
and may cause serious injuries.
Adjusting the chinstraps length
Proper chinstraps length
Fasten the One-touch buckle securely when
wearing the helmet. The proper chinstrap length
would allow your forefinger to slip in between the
chinstraps and your neck. If the length is not
proper, please adjust the length of the chinstraps.
Press the button
<Side view>
Chinstrap edge
One-touch buckle
Chinstrap
Shortening
Lengthening
Release button
Release
Insert into the buckle
Chinstrap
Hook and
loop
fastener
(inside)
Hook and loop
fastener
(inside)
Hook and
loop fastener
(inside)
Hook and
loop
fastener
(inside)
One-touch
buckle
One-touch
buckle
Chinstrap with the
chinstrap cover
Chinstrap with the
chinstrap cover
Hook and loop
fastener
Hook and loop
fastener
Pull out the
chinstrap from
here
Pull out the
chinstrap from
here
Remove the chinstrap
cover from the chinstrap Remove the chinstrap cover from the chinstrap
Fastening
Unfastening
“ECE22-05 approval label”
●This label shows that the product conforms to the test standard ECE22-05, and is issued one sheet per one
product with a serial number authorized by the inspection organization thereof. In sales in European areas, it is
obliged to display this label by sewing it directly on a chinstrap.
INSTRUCTION MANUAL
PRIOR TO USE, READ THIS INSTRUCTION
MANUAL THOROUGHLY AND KEEP THIS
FOR FUTURE REFERENCE
BEFORE USE
Chin liner
Breath Guard
Centre of the helmet
Breath Guard
Fig.1
Hook and loop fastener
Cheek pad
Snap
Snap
15 16
CAUTION
CAUTION
10
How to attach the shield
Shield
*This explanation indicates the left side when the helmet is worn.
aInsert the projection B into the space on the
shield ratchet as shown in Fig.1. and Fig.2.
Place the notch area of the shield on the
ratchet and then align the small projection A
and the edge of the lever as indicated in Fig.3.
bSet the small projection A into the ratchet by
pulling the lever down. (Fig.4)cFollow the
same steps on the other side to attach the shield completely.
Fig.1 Fig.2 Fig.3
Fig.4
CAUTION
●Do not push or twist the shield by force when installing it. Such action may
damage the shield and ratchet system.
●After the installation of the shield, be sure to pull it lightly towards the removing
direction to make sure that it is securely installed.
●After the installation of the shield is completed, open and close the shield three
to four times to make sure that the shield works properly.
WARNING
●After the installation of the shield, make sure the shield is securely installed and that
it is properly opened and closed before riding. If the shield does not work properly,
or is installed insecurely, it may cause a failure in opening and closing the shield or
lead to the removal of the shield while riding, thereby causing a great risk. If the
opening and closing operations are not properly performed or abnormal noise is
heard during these operations, check the steps in the installation procedure and
repeat the installation procedure from the start.
●The shield is a consumable item. If the shield surface is damaged by a bug, stone,
etc., it may hinder the vision, thereby causing a great risk. If the shield gets
extremely dirty or scratched, replace it with a new one.
Insert in-betweenInsert in-between
Insert in-between
Wind Shutter-2
Cheek pad
Cheek padCheek pad
Fig.2
Installation is complete.
Rubber
trim
(front)
Wind Sutter-2Wind Sutter-2
Fig.3
Fig.4
Included in package
Chinstrap cover ×1 set
(Right and Left)
Exchangeable
Exchangeable among
all sizes
Fig.2
Chinstrap
Cheek padCheek pad
1 2
Instruction Manual Table of Contents
Helmet Description
NOTES BEFORE USE•••••P-3
FOR SAFE AND COMFORTABLE USE
CHINSTRAPS
AIR-CONDITIONING FUNCTION OF VENTILATIONS
SHIELD
INTERIOR (INNER PAD AND CHEEK PADS)
WIND SHUTTER /BREATH GUARD
● KAMUI Series Parts List and Table for Replacement•••••P-25
Contact for inquiries and request for repair•••••P-24
KAMUI Instruction Manual Table of Contents•••••P-1
Helmet Description•••••P-2
INQUIRIES/ PARTS LIST
Rear Ventilation
Shell
Chin Ventilation
Shield Ratchet
Pins for Pinlock® Original Insert Lens
(Eccentric pins)
Integrated Wake Stabilizer
(PATENTED)
Head Ventilation
Shield
Inner
Sunshade
3
7
3
"Ventilation System" and "Wake Stabilizer PATENTED"
Head Ventilation
Head Ventilation Rear Ventilation
Chin Ventilation
8
4Open/Close Each Ventilation
Open/Close Head Ventilation
Open/Close Rear Ventilation
9
WARNING
●Operating the shutter while riding is very dangerous. Never operate the shutter
while riding. Operate it before riding.
●The air-ducts (air intakes and discharge holes) of each of the ventilations are
designed in the proper sizes and quantities considered a large impact in the
event of accidents and falling down. Customizing by enlarging or making more
air-ducts would reduce the safety performances significantly and can cause
serious injuries in case of an accident. Never customize your helmet.
Repairing the ventilations
When each ventilation is damaged, contact your local authorized Kabuto dealer.
(See Pages 24 to 26). Please be informed that we may not accept repairing, in the
case the safety performance of the helmet will be degraded.
CAUTION
●Flex the shield properly when fitting the Pinlock® Original Insert Lens. Otherwise,
eccentric pins may be damaged.
●Clean the inside of the shield before applying the Pinlock® Original Insert Lens. Pay
attention not to touch the anti-fogging part of the silicon seal on the Pinlock® Original
Insert Lens.
●Do not use any petroleum products, thinner, glass cleaner, etc. It will degrade the
material of the Pinlock® Original Insert Lens.
●Do not leave the Pinlock® Original Insert Lens where the temperature may surpass
50ºC or near a heater, neither use a drier nor fire for drying. Heat may degrade the
material of the Pinlock® Original Insert Lens.
CAUTION
●Pinlock® Original Insert Lens is only for exclusive visors.
●If rain or water drops come in the space between the Pinlock® Original Insert Lens
and the shield, please detach the Pinlock® Original Insert Lens from the shield and
dry them out. Then, reattach the Pinlock® Original Insert Lens on the shield.
●Please remove the Pinlock® Original Insert Lens at times for maintenance. Otherwise
the silicon seal of the lens would adhere to the shield.
●Do not use any shields or pins other than exclusive ones for the Pinlock® Original
Insert Lens.
●Please be informed that if you are riding with the ventilations closed or using the Wind
Shutter, may cause the Pinlock® Original Insert Lens to become fogged.
●Please replace Pinlock® Original Insert Lens if the anti-fog performance decreases
and/or being scratched.
●Silicon seal may come into view depending on the riding position.
CAUTION *Pinlock®Original Insert Lens
17
19 20
18
aUndo the snaps at the forehead area
by pulling them down as shown in
Fig.1
bUndo the 2 snaps at the rear, then the
inner pad can be removed. (Fig.2)
aInsert the interlining at the temple
areas as shown in Fig.1.
bInsert the 3 snaps on the front as
shown in Fig.2.
cFasten the 2 snaps at the rear to
complete attaching the pad.
Snap
KAMUI interiors are exchangeable as shown in the table below. Fine fitting can be
achieved by changing only cheek pads etc.
Exchangeable Included in package
Inner pad x 1 pce
Inner pad x 1 pce
Interchangeable between
the sizes of XS, S and M
Interchangeable between
the sizes of L and XL
Pad size (thickness)
XS(19mm)
S (15mm)
M(9mm)
L (12mm)
XL (9mm)
Shell size
M
L
Exchangeable Included in package
Cheek Pad ×1 set
(Right and Left)
Exchangeable among
all sizes
Pad size (thickness)
XS (39mm)
S (35mm)
M(24mm)
L (29mm)
XL (20mm)
Shell size
M
L
■KAMUI Cheek pads
■KAMUI Chinstrap cover
CAUTION
●Install the Wind Shutter-2 securely.
Insecure installation may cause falling of
the Wind Shutter-2 while riding.
●Do not use an adhesive agent or similar items but install the Wind Shutter-2 according to the procedure
given above. Some components of an adhesive agent may damage the material of the helmet.
Remove/Replace Wind Shutter-2
How to install Wind Shutter-2
aRefer to Fig.1 and check the front side
and back side of the Wind Shutter-2.
b
As shown in Fig. 2, turn the helmet over
and attach the Wind Shutter-2 on the
front (chin area) of the helmet. In doing
this, insert the interlining of both sides of
the Wind Shutter-2 in-between the front
area of the cheek pad and the rubber
trim.
c
As shown in Fig. 3, insert the interlining
of the Wind Shutter-2 uniformly into the
inside of the rubber trim from both sides
towards the center.
d
Put the interlining to such an extent that
the edge of the frame rubber is almost flat
with the Wind Shutter-2. The attachment
of the Wind Shutter-2 is complete (Fig.4).
2221
The Wind Shutter-2 is included in the package as a standard accessory. This
accessory is intended to reduce the introduction of wind from chin area while riding. It
can be attached and detached as desired according to seasons and intended
applications.
Fig.1
KAMUI Series Parts List and Table for Replacement
KAMUI Series Parts for Repair
KAMUI Series Parts for Replacement
1
2
3
3
1
2
3
4
5
6
7
8
4
5
6
7
8
3-b
6(L) 6(R)
3-b
3-a(R)
3-a(L)
5(R)
5(L)
CF-1-PShield (standard:Clear) × 1pce
CF-1 Inner Sunshade (standard :smoke) × 1 pce
3-a:C-1K ratchets (R/L) ×1 set
3-b:6 x 6 screw ×4 pcs
3-b:6 x 6 screw ×4 pcs
♦ See Page 21(XS, S, M, L, XL) Inner pad ×1 pce
♦ See Page 21(XS, S, M, L, XL) Cheek pads (R&L) ×1 set
♦ See Page 21 Chinstrap cover(R/L)×1set
Breath Guard No.4× 1pce
Wind Shutter No.2× 1pce
Breath Guard Pro× 1pce
Each colour / Right side • Each colour/ Left side
Each colour
Each colour
Common is all sizes
Head Ventilation
Rear Ventilation
Chin Ventilation
Inner Sunshade, Opening/Closing lever
Purchasable
Purchasable
Purchasable
Exclusive to KAMUI
A
B
C
D
No. Parts
Part name & repairs Colour/ Side Remarks
Contains
■Refer to page 24 for more information on repairing.
25 26
How to remove Wind Shutter-2
Firmly hold the interlining area around
the centre of the Wind Shutter-2 and pull
it up. Then the Wind Shutter-2 will be
removed.
23
CAUTION
To remove the Wind Shutter-2, gently
pull up and take off carefully. Otherwise
the cloth and/or a part may be damaged.
Remove/Replace Breath Guard
The "Breath Guard" can be detached or
attached according to your needs.
ATTACHING:
As shown in the figure, set the centre of
the Breath Guard onto the centre of the
helmet, and push in the Breath Guard
between the shield rubber trim and the
chin liner.
DETACHING:
Grip the Breath Guard securely, and pull
it out to remove it.
CAUTION
Do not use an adhesive agent but follow
the procedure given above to attach the
Breath Guard.
Some components of an adhesive agent
may damage the material of the helmet.
24
14
Remove/Replace Cheek Pads
–How to remove the cheek pads–
Remove the cheek pad from hook and loop
fastener and the snaps by gripping it firmly then
pull it out.
(Fig.1)
Replace Cheek pads: (Fig.2)
aCheck the side of the cheek pad.
bInsert the interlining in-between the shell and
the liner, then place the chinstrap as shown.
cFasten securely the hook and loop fastener
and 2 snaps on the back of the cheek pad.
Follow the same steps on the other side.
When removing the cheek pad, be sure to grip
the base of cheek pad where the hook and loop
fastener and the snaps are attached. Otherwise,
the cheek pad may be damaged.
CAUTION
Be sure that the cheek pads are attached on the helmet securely before riding. It is
hazardous to use this helmet without cheek pads or attaching the cheek pads
improperly.
CAUTION
To remove the inner pad, do not pull the interlining and snaps by force but gently pull
them out. If they are pulled out by force, the fabrics of the pad and other parts may be
damaged.
CAUTION
●If the inner pad is not securely installed, the helmet may be unstable while riding,
thereby causing a great risk. Fasten the snaps properly.
●It is also important to attach the pads properly to wear your helmet comfortably.
10
Remove/Replace Inner pad
How to remove the inner pad: How to attach the inner pad:
Fig.1
Fig.1
Fig.2
Fig.2
9
11
12
Helmet Interiors
●Chinstraps
●Cheek Pads
●Inner Pad
●Chinstrap Covers
●Wind Shutter-2 (Packaged in)
Breath Guard
(Packaged in)
Inner Sunshade Open/Close Lever
To close
To closeTo Open
Slide the lever backwards.
Air-duct
Slide the lever forwards.
Wake StabilizerPATENTED.
Front Front
Interlining
Left cheek Right cheek
Interlining
C
Air-ducts (inside)
Open/Close Chin Ventilation
To closeTo Open
4
Front Back
*Stitching side is back
Wind Shutter-2
Interlining
Wind Shutter-2Wind Shutter-2
5
CAUTION!
Do not put strong pressure on the ventilations.
Make sure to treat them with care.
*Please read “WARNING” and “Repairing the ventilations” on the next page.
How to replace the Inner Sunshade
5Remove/Replace Shield
Fig.1
Fig.2
CAUTION!
●Do not pull the shield out nor twist it forcibly when detaching. This may cause
damage the shield and/or ratchet system.
●Please handle the detached shield with care in order not to get it scratched.
ShieldShield
*This explanation indicates the left side when the
helmet is worn.
aOpen the shield as far as it goes and
then align the small projected part (A)
and the edge of the lever as indicated
Fig.1.
bAs pulling the lever down, pull the shield
out in the direction of the white arrow, so
one side of the shield can be detached
completely. (Fig.2)
Follow the same steps on the other side to detach the shield completely.
How to detach the shield
Pull A outPull A out
Edge of the leverEdge of the lever
After attaching the Inner Sunshade,
open/close it 3 to 4 times to check if the Inner
Sunshade works properly. If abnormal noise
is heard and/or the Inner Sunshade cannot
be opened/closed properly, please reattach it
after reading the above procedure carefully
aPull the lever upwards to close the
Inner Sunshade completely.
11
6Remove/Replace Shield Ratchets
Turn the Shield Ratchet Screws on the Shield
Ratchet counterclockwise using a proper sized
flat-blade screwdriver until the screws are
removed. Then, the shield ratchet can be
removed. Follow the same procedure to remove
the Shield Ratchet on the other side.
How to remove the Shield Ratchet:
aFirst, check the side of the Shield
Ratchet as shown in Fig.1.
bPlace the Shield Ratchet in the hollow
space on the side of the helmet and
align the mounting holes on the shield
ratchet with the mounting holes on the
helmet (Fig. 2).
cFasten the both Shield Ratchet Screws
clockwise securely. Repeat the same
procedure on the other Shield Ratchet.
Then the Shield Ratchets are installed
(Fig. 3)
LeftRight
The The “Shield Ratchet” is a part to control open/close the shield and remove/replace
the shield ratchets. When the shield is completely removed by the procedure
mentioned in 5 “Remove/Replace Shield”, the Shield Ratchet appears.
How to install the Shield Ratchet:
Fig.1
Fig.2
Fig.3
12
Open/Close Inner Sunshade
WARNING!
● Open the Inner Sunshade during night rides or
in a tunnel.
●Open the Inner Sunshade when expecting
change in temperature such as sudden rain,
right after entering a tunnel or a place with a
large height difference. In those situations, the
Inner Sunshade can be fogged suddenly
because of the difference in temperature
in-and-outside the helmet.
Slide the lever upwards to close the
Inner Sunshade.
Slide the lever downwards to open the
Inner Sunshade.
7Open/Close Inner Sunshade
This helmet is equipped with the Inner
Sunshade which protects your eyes from
glare in day time. This can be
open/closed according to your needs.
bAttach the Inner Sunshade
from the right side when the
helmet is worn. Set the clip
securely into the metallic
parts which you can see
from the attachment space.
To closeTo open
cSet the other side securely
into the “red attachment
space” to complete the
attachment of the Inner
Sunshade.
13
How to remove Inner Sunshade
Follow the above procedure to remove/replace the Inner Sunshade.
Pulling the inner Sunshade forcibly or removing/replacing it in any other way may
damage the Inner Sunshade and/or any parts on the helmet.
aClose the Inner Sunshade completely.
b(Detach the Inner Sunshade from the
right side when the helmet is worn.)
Hold the Inner Sunshade firmly and pull it
out in the direction of arrow.
cFollow the same procedure on the other
side to remove the Inner Sunshade
completely.
8Remove/Replace Inner Sunshade
CAUTION!
Do not operate the Inner Sunshade
by holding it directly with your hand,
otherwise, the Inner Sunshade may
be damaged. Operate it with the
Open/Close lever.
■KAMUI Inner pad
Snap
Fig.3
CF-1-P Shield
CF-1 Inner Sunshade
CF-1 Shield ratchets set
Shield ratchet screws set
KAMUI Inner pad
KAMUI Cheek pads set
KAMUI Chinstrap covers
Breath Guard No.4
Wind Shutter No.2
Breath Guard Pro
A
B
D
Attachment of PINLOCK® Original Insert Lens •••••P-15
Original Insert Lens
Air-duct
Slide the lever to the right. Slide the lever to the left.
Lever Lever
Air-ducts (inside)
Inner SunshadeInner Sunshade
Inner Sunshade
Open/Close
lever
Open/Close
lever
Inner
Sunshade
Open/Close
lever
Open/Close
lever
Clip
Metallic partsMetallic parts
Attachment
space
(Red)
Rear Ventilation
Outer air
Outer air
Head Ventilation
Outer air
Liner
Shell
Liner Shell
Humid air
*Section view
2012-JUN-EKMI-QDK
Kabuto Europe B.V.
Theems 27, 2491 BR Den Haag
The Netherlands
URL: www.kabuto-europe.com
Optional Parts
NOTES BEFORE USE
Thank you very much for purchasing a KABUTO helmet.
This Instruction Manual describes proper handling, various functions and
remove/replace each part of this helmet. Please read this Instruction Manual
thoroughly prior to use.
After reading this, keep this Manual for future reference.
The helmet is just one element of protection, it is intended to minimize the risk
in the event of an accident. It cannot ensure complete safety.
Use this helmet properly based on this understanding.
Please understand and follow the instructions and information in this
Instruction Manual to enjoy your safe ride.
It is very dangerous to wear a too large sized helmet. This may wobble while riding. If you wear a
too small sized helmet, it tightens up and hurts your head. Thus, it is important to select the proper
size.
The helmet is designed to be retained by straps under the chin. In order to assure proper
protection, the helmet should fit your head. When worn, adjust it to rest properly on the head,
securely fasten the chinstraps to ensure safety. The chinstraps prevent the helmet from coming off
in most cases.
In order to fully maintain the performance of this helmet, do not attempt to take apart or change the
helmet in any manner such as making holes in it or cutting it.
Liners are essential for the intended performance of the helmet.
This helmet has been designed to absorb the impact energy when components as shell and liners
are partially destroyed by an impact.
Even if visually no damage is apparent, it could be seriously damaged by a small impact.
Regardless of the degree of damage, the helmet that underwent an impact or was abused even
only once should not be used anymore.
Always handle the helmet with care and make sure that no one sits on it or drops it.
Never use the helmet once impacted
Clean the helmet with soft cloth, using common ph-neutral detergent diluted with clear water. The
cloth should not be soaking wet. Then wipe the helmet gently with a clean wet soft cloth and leave
it to dry completely, but not in direct sunlight.
With regard to helmets with removable interiors, carefully read the instruction manual for that
model before attempting to remove the interiors and carry out cleaning according to the
explanation provided. To clean the helmet do not use saline water or hot water (above 50º).
Never modify the helmet
Select the proper size!
The storage of the helmet
Shield care and cleaning
Notes for use of full-face helmet
After using the helmet, stow it away in the helmet bag and store on a level place such as a shelf;
the helmet may be damaged if it rolls around or falls down.
Do not leave the helmet in direct heat above 50ºC e.g. next to a heater or under direct sunlight in a
car.
Cautions for shield
If the visor is marked “Day Time Use Only”, visibility is limited to daylight conditions and it is not
suitable for use at night.
Tinted lenses are not suitable for use at night.
A visor and goggles with scratches lowers the visibility and this is very dangerous. Such visors
should never be used at night and should be replaced.
Contact with petroleum products and other solvents may impair the optical properties and weaken
the strength of the visor.
Never try to open or close nor remove the visor while riding.
After using your helmet, with a wet soft cloth, lightly wipe off any grime (e.g. dead insects, dirt,
sand, dust, etc.) on the shield and then fully wipe it clean using a dry soft cloth. When the shield
gets wet (e.g. rainwater), it should always be wiped with a soft cloth after use.
When cleaning the shield, never use any petroleum-based solvents or detergents containing
abrasives.
Contact with petroleum products and other solvents may impair the optical properties and reduce
the mechanical strength.
To clean the shield, apply some common ph-neutral detergent diluted with clear water using a soft
cloth and wipe gently. Finally, wipe it dry with a lint-free soft cloth. To clean the shield, do not use
saline water or hot water (above 50ºC).
When you wear a full-face helmet, the temperature in the helmet is maintained nearly constant
while riding but the surroundings are constantly changing since you are moving at a high speed.
For this reason, in case of sudden rain, entering a tunnel or in a place with a large height
difference, the shield can be fogged suddenly because of the difference in temperature
in-and-outside the helmet.
In case such a risk is expected, please use caution with adjusting the shield or slowing down your
speed in advance.
Never open or close the shield nor adjust the ventilation shutter while riding since it is very
dangerous. Adjust the shield before riding.
Any paint, glue, adhesive stickers, etc. (or the use of detergents and solvents other than those
prescribed) may not only reduce the original protective performance of the helmet considerably,
but may also cause damage to the helmet that cannot be detected by the naked eye.
Do not paint or apply solvent
Handle your helmet with care
Do not toss your helmet over a floor or sit on it. The helmet absorbs an impact every time it is
handled roughly and its impact-absorbing capacity will be decreased. Handle your helmet with
care to assure its full intended function in the event of an accident.
Do not use your helmet for any purpose other than to use for protecting your head while riding.
Fasten the chinstraps before riding
Helmet care and cleaning
6
The ventilation system
effectively takes outer air in
and pushes the inner humid air
out by the air pressure from
the front while riding. The
ventilations are equipped with
a shutter which prevents cold
air and water drops from
coming into the helmet.
Ventilation System:
The Wake Stabilizer PATENTED, KABUTO’s unique
system, is developed by analyzing the results of
wind tunnel experiments at several angles. This
unique system controls the airflow around the
helmet and reduces loads while riding.
Integrated Wake Stabilizer PATENTED
To Open
Small
projection
(A) on the
shield
Projection
B on the
shield
Space on the
shield ratchet
Small projection A
on the shield
Edge of the lever
Insert the small
projection A.
Proper sized
flat-blade
screwdriver
Shield
Ratchet
Screw
Shield
Ratchet
Screw
Open/Close
lever
Open/Close
lever
*Easier to remove/replace the Inner Sunshade
after detaching the shield.
Pull out the
Inner Sunshade
to the front
Pull the other
side out in the
same way
* Easier to remove/replace the Inner Sunshade after
detaching the shield.
Check the lever is
up completely
Attachment
space
Where
cheek
touches
Interlining
NOTE
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers
●The interiors of this helmet are washable by a washing machine. Put each pad in a washing
net and wash them separately.
●Use detergent in cold water or warm water for cleaning. Never use hot water, chemical
detergents, and organic solvents for cleaning the pads. The use of these agents may degrade
the quality and damage the pads.
●Even commercially-available detergent may cause a little discolouration of the pad depending
on the type of detergent. Thus, please wash each pad separately as much as practical.
●If the pad is washed in a washing machine having a drying function in which the temperature is
increased to 50ºC or more, it may cause deterioration in quality and damage of the pads.
Do not use such a device for cleaning of the pad.
●Drain a pad after washing and dry the pad in shade so that it is not exposed to direct sunlight.
After making sure that it is dried enough, attach it on the helmet.
●The inner pad and the cheek pad are consumable items. Even under normal usage, the fabric
material and inner foam may be worn and deteriorated depending on the frequency of usage.
Please replace the pads with new ones as appropriate.
Cleaning of Inner Pad,
Cheek Pads and Chinstrap Covers
IMPORTANT
Rubber trim
(front)
Put the interlining into the inside of the rubber trim
from both sides towards the center by hands.
Rubber trim
(front)
Put the interlining to such an extent that the edge of
the frame rubber is almost flat with the Wind
Shutter-2.
Hold the interlining around
the centre and pull it
up.
Insert
in-between
Shield rubber
trim
Shield
rubber
trim
NOTE Breath Guard Pro (Optional accessory)
In addition to this standard Breath Guard, Breath Guard Pro, a larger size than Breath
Guard is available as an optional accessory. Breath Guard Pro is available from an
authorized dealer of KABUTO helmets.
Contact for inquiries and request for repair:
●When sweat comes out from the body, COOLMAX® allows discharging body moisture to
the outside and takes in air from the outside to cool and dry your body. As a result, the
temperature on the body surface is lowered and exercise great moist adjustment
accordingly.
●COOLMAX® provides a natural touch to the texture with soft and light weight and good
permeability properties.
*COOLMAX® is the registered trade name of INVISTA.
■Contact the authorized KABUTO dealer for request of repair.
○After inspected, there may be a case that your order of repairing cannot be accepted
if it is judged that the safety performance of the helmet cannot be assured by
repairing.
■The following parts cannot be repaired in terms of assuring the performance of the
helmet.
●Helmet body (Shell)
●Shock absorbing liner
●Chinstraps including One-touch buckle (Main body, chin area )
*Contact authorized KABUTO dealers for detailed information about repair and others.
Contact an authorized dealer of Kabuto helmets about the products and request for repair
Request for repair
Parts that cannot be repaired
COOLMAX® is used for the interior fabrics in order to allow quick
evaporation of sweat and brings cool and comfortable use.
Evaporate sweat quickly to achieve cool and comfortable use
OP
●The parts listed above are available from an authorized KABUTO dealer.
●Parts with colour variations, specify your desired colour in placing an order.
●The materials and specifications are subject to change without notice for further improving the
performance of the product.
●Check out our website for details about the parts.
●These parts are repaired at cost of the user except damage attributable to a defect in material and workmanship
of KABUTO helmets.
CAUTION
Use the proper sized screwdriver to remove the Shield Ratchet Screws. Turn the
screw by applying the screwdriver vertically to the screw. If the improper sized
screwdriver is used or the screw is turned diagonally, the threads may be
stripped.
●The following parts cannot be repaired in terms of assuring the performance
of the helmet.
•Helmet body (Shell) •Shock absorbing liner
•Chinstraps including One-touch buckle
●Contact the authorized KABUTO dealers for detailed information on repairing.
CAUTION
Humid air inside of the helmet
Optional Parts
Pinlock®Original Insert Lens
For SAF-P 1 sheet
Pinlock® Original Insert Lens prevents the shield from fogging caused by thermal
changes in winter or rainy weather etc.
Maintaining the proper space between the shield and the Pinlock® Original Insert
Lens provides clear vision by balancing the inner and outer temperature.
Pinlock®Original Insert Lens:
PINLOCK® Original Insert Lens is the effective anti-fog sheet.
The visor of your helmet has PINLOCK® pins (eccentric pins).
The PINLOCK® Original Inset Lens can be purchased at the dealer where you bought
your helmet.
Original Insert Lens
Pinlock® has international patent protection and is a registered brand name of Pinlock systems B.V. Further patents have been applied for.
aApply the silicon seal side of the Pinlock® Original Insert Lens on the inside of the
shield, without peeling off the protective film on the lens. At the time, apply the
Pinlock® Original Insert Lens on the inside of the shield by clicking it into the
eccentric pins. (Fig 1 and 2)
Fig.2Fig.1
Section view
Protective film
Silicon seal Shield
Inside of the shield
Pinlock®
Original Insert Lens
–How to Fit the Pinlock® Original Insert Lens–
Fig.3 Fig.4
Silicon sealSilicon seal
bFlex the shield when the Pinlock® Original Insert Lens into the eccentric pins.
(Follow 3)
Flex the shield when the Pinlock®
Original Insert Lens into the
eccentric pins.
aRemove the shield from the helmet.
bRemove the Pinlock® Original Insert Lens from
the eccentric pins with flexing the shield. (Fig.6)
How to Adjust Pinlock® Original Insert Lens
after Attachment:
Adjust the Pinlock® Original Insert Lens if
there is any space between the lens and the
shield.
aRemove the shield from the helmet and
detach the Pinlock® Original Insert lens from
the shield.
bAdjust the eccentric pins by turning them
with a tool. (Fig. 7)
cFit the Pinlock® Original Insert Lens back on
the shield. Make sure the Pinlock® Original
Insert Lens and the shield do not have any
space in-between after attaching the shield
on the helmet. If there is any space please
follow the same steps again.
Fig.5
Protective film
Shield
Eccentric pins
Silicon seal
*without any space
Fig.6
Fig.7
Face the eccentric pins inwards
Face the eccentric pins outwards
Eccentric pins Eccentric pins
cMake sure if the overall
silicon seal of the
Pinlock® Original Insert
Lens is attached firmly
to the shield by
mounting the shield on
the helmet. If there is
any space between
them, refer to “How to
Adjust Pinlock® Original
*Please mount the shield on the helmet when checking if the Pinlock® Original Insert Lens is attached firmly to the
shield. Otherwise, the shield might be spread out by the pressure from the lens and it cannot be assured if the lens
has attached on the shield firmly.
dPeel off the protective film of the Pinlock® Original Insert Lens.
– How to Remove Pinlock® Original Insert Lens –
Section view of
the shield
Insert Lens after Attachment” and adjust the lens.
so that the Pinlock® Original Insert Lens will be pushed out
and there would not be any space between the Pinlock®
Original Insert Lens and the shield.
so that the Pinlock® Original Insert Lens will
be loose.
Facing the eccentric
pins inwards
Facing the eccentric
pins outwards
Pinlock® Original Insert Lens is pushed out so
that it will be in close contact with the shield.
Loosening the Pinlock®
Original Insert Lens
* Please read carefully the “CAUTION” and the “CAUTION *Pinlock® Original Insert
Lens” on the next page.
1Remove/Replace Chinstrap Covers•••••P-5
2Fastening Chinstraps•••••P-6
3"Ventilation System" and "Wake Stabilizer PATENTED"•••••P-7
4Open/Close Each Ventilation•••••P-8
5Remove/Replace Shield•••••P-9
6Remove/Replace Shield Ratchets•••••P-11
7Open/Close Inner Sunshade•••••P-12
8Remove/Replace Inner Sunshade•••••P-13
9Remove/Replace Cheek Pads•••••P-18
10 Remove/Replace Inner Pad•••••P-19
Exchangeable Inner Pad, Cheek Pads and Chinstrap Covers •••••P-21
Cleaning of Interiors •••••P-21
11 Remove/Replace Wind Shutter-2•••••P-22
12 Remove/Replace Breath Guard•••••P-23
NOTE
IMPORTANT
Shield Ratchet Screw
Screw-inserting holes
1205342_Kabuto Engels.indd 8 13-07-12 09:53