Kallista P23010 User manual

1085231-2-A
Page 1 of 3
P23010
Floor Riser Support Assembly
THANK YOU FOR CHOOSING KALLISTA
BEFORE YOU BEGIN
TOOLS AND MATERIALS
1. ASSEMBLE THE PIPE HOLDERS & TEE BRACKET
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before
you install your Kallista product. If you encounter any installation or performance problems, please do not
hesitate to contact us at the phone number listed at the bottom of the page.
Priorto installation, unpack the floor riser support assembly and inspect it fordamage. If the product is
damaged, please contact Kallista immediately at the phone numberlisted at the bottom of the page.
Shut off the main watersupply.
Observe all local plumbing and building codes.
The installation of the riser support assembly should coincide with the installation of the floor risers.
To prevent damaging the tub, the floor riser support assembly should be mounted a minimum of 12” from the
floor.
Kallista reserves the right to make revisions in the design of plumbing products without notice, as specified in
the Price Book.
Silicone
Hex
Wrench
Pencil Drill Hacksaw
Pipe Holder
Pipe Holder
Tee Bracket
Thread the pipe holders onto the tee bracket.
Use the hex wrench to back the set screws out slightly,
so that the floor risers (not provided) can be inserted
without scratching them.
Questions? Problems? For additional assistance, please contact Kallista's Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION INSTRUCTIONS
Phillips
Screwdrivers
Strap
Wrench
Tape Measure
or Ruler
Set Screw

1085231-2-A
Page 2 of 3
P23010
Floor Riser Support Assembly
2. ATTACH THE PIPE HOLDERS TO THE FLOOR RISERS
3. CUT THE CONNECTING ROD TO SIZE
Carefully slide the straight end of the floor riser through
the pipe holder and the flange.
Thread the floor riser into the supply rough-in and tighten
it with a strap wrench.
Adjust the flange so that it rests on the floor. Tighten the
set screw.
Repeat for the second floor riser.
Slide the pipe holders and tee bracket up the floor risers
to the desired position, being careful not to scratch the
floor risers.
NOTE: To prevent damaging the tub, the floor riser
support assembly should be mounted a minimum of
12” from the floor.
Tighten the set screws.
Questions? Problems? For additional assistance, please contact Kallista's Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALLATION INSTRUCTIONS
Set Screw
Set Screw
Floor Riser
Floor Riser
Set Screw
Pipe Holder
Tee Bracket
Pipe Holder
Flange
Measure the distance from the end of the tee bracket to
the tub. Add 3/4” to this distance. This is the length of
the connecting rod.
Add 3/4” to this
distance
1 2 3 4 5 6 7 8 9
Mark this distance on the connecting rod, measuring
from the end with the ball toward the end with the hole.
Use a hacksaw to cut off the connecting rod at the
mark, being careful not to scratch the finish of the
connecting rod.
Remove any burrs or sharp edges.

1085231-2-A
Page 3 of 3
P23010
Floor Riser Support Assembly
INSTALLATION INSTRUCTIONS
4. COMPLETE THE INSTALLATION
Questions? Problems? For additional assistance, please contact Kallista's Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Slide the mounting plate so that it is flat against the side of
the bathtub, making sure the holes in the mounting plate line
up with the pilot holes in the bathtub.
Attach the mounting plate to the bathtub with the self tapping
screws.
Tighten the set screw in the tee bracket.
Mounting Plate
Self Tapping Screws
Tee Bracket
Set Screw
Cushion
Tee Bracket
Mounting Plate
Connecting Rod
Rotate the tee bracket toward the floor slightly.
Insert the cut end of the connecting rod into the tee bracket.
Rotate the connecting rod and tee bracket back up so that the
connecting rod is level.
Slide the mounting plate so that it is touching the side of the
bathtub.
Mark the location of the holes in the mounting plate.
Slide the mounting plate out of the way. Drill 1/8” dia x 5/8”
deep pilot holes, being sure that they are perpendicular to the
side of the tub.
WARNING: To avoid damaging the tub, do not drill
the holes deeper than 5/8”.
Apply a dab of silicone to the back of the cushion and position
it on the tub, centered between the three pilot holes.
Adjust the connecting rod so that the cushion is pinched
between the connecting rod and the bathtub.
Mounting Plate
Connecting Rod
Assemble the connecting rod and mounting plate.