kd frames Charleston Plus Platform Bed XL-TWIN User manual

A-80-P BED RAIL (2) - 80”
A-37 REGULAR SLAT (14) - 37”
A-37-C CONNECTOR SLAT (2) - 37”
A-15L FOOTBOARD
LEFT LEG (1) 15”
A-15R FOOTBOARD
RIGHT LEG (1) 15”
A-40L HEADBOARD
LEFT LEG (1) 40”
A-40R HEADBOARD
RIGHT LEG (1) 40”
A-22 HEADBOARD PICKET (6) 22”
HARDWARE LIST
1
H-10 HEX WRENCH
H-3 CROSS DOWEL
12
12
H-21 2 - 1/2” BOLT
H-20 1 - 1/2” WOOD SCREW
10
All wood is from the Tulip Poplar tree which can have dark streaks in the heartwood.
We try to use this wood for parts that don’t show in the final assembly. For a video
on how to assemble this frames, please visit kdframes.com.
PARTS LIST
#2 PHILLIPS HEAD SCREWDRIVER REQUIRED
Manufactured by
394 Dairy Pak Rd. • Athens, GA 30607
kdframes.com • [email protected]
CHARLESTON PLUS PLATFORM BED
XL-TWIN
Instructions for the
SKU# 3994-CP-XT
This bed frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a few
weeks. This will happen in 20 to 30 minutes if placed in direct sunlight. Tulip Poplar can be left unnished,
clear nished, stained, or painted. Satin polyurethane (oil or water based) works well.
Painting: It is best to start with an interior primer and lightly sand before painting.
Staining: Light sand before staining. Wipe stain on with a rag until you get the desired color. If you are going
to use a top coat (such as polyurethane), do not sand again until after the rst coat, and then be careful not
to sand away the stain.
Finishing: All nishes work well with Tulip Poplar. A simple was nish over stain (Minwax for example) is easy.
An oil nish such as Danish oil can be used. Or a clear coat such as polyurethane works well to seal the wood.
With polyurethanes, the rst coat acts as a sanding sealer. You should lightly sand (180-220 grit sandpaper)
after the rst coat, wipe the wood clean, and then build up coats for the desired eect.
Knockdown Frameworks, Inc. warrants all of its products for ve years against any defects that are due to faulty materials or workmanship. We will
promptly correct such defects by replacement without charge. This warranty covers porduct defects only and will expire ve years after date of
purchase by the original consumer purchaser, with proof of purchase required. This warranty does not apply to damage caused by and resulting
from misuse, neglect, accident, or improper operation, maintenance, storage, transportation, or handling of the product. This warranty is for the
original consumer purchaser for residential use only and does not apply if the product is used in any commercial application (such as rental
property). This warranty does not cover any incidental or consequental damages. If you feel that you have a claim under this warranty, please
contact us at [email protected].
A-33-HB HEADBOARD BOTTOM (1) - 33”
A-33-HT HEADBOARD TOP (1) - 33”
A-33-F FOOTBOARD (1) - 33”

1
RAIL POCKETS MUST
ALL BE ON THE
SAME SIDE
FRONT VIEW
BACK VIEW
Assemble the headboard by pushing the
(7) Headboard Pickets into holes on the
Headboard Bottom (A-33-HB) .
Then push the Headboard Top (A-33-HT)
down onto the pickets
Attach the Headboard Legs (A-40-L and A-40-R)
to the Headboard by pushing them onto the
dowels. Be sure that the rail pockets are all
facing the same side. Then use (6) 1 - 1/2”
Wood Screws (H-20) to attach the Legs.
2
HEADBOARD ASSEMBLY

Align the Left Footboard Leg (A-15L) and
Right Footboard Leg (A-15R) so that the
rail pockets are on the front.
Turn the Footboard (A-33-F) so that the
pocket holes are facing the front.
Then push the dowels into the holes on the legs.
WOOD SCREWS
GO IN THESE
POCKET HOLES
Use a phillips screw driver to attach
the Legs to the Bed End using
(4) 1 - 1/2” Wood Screws (Black) (H-20).
3
RAIL POCKETS MUST
ALL BE ON THE
SAME SIDE
A-15L
A-15R
FOOTBOARD ASSEMBLY
Use 2-1/2” Bolts (H-21) and
Cross Dowels (H-3) to attach
Bed Rails (A-80-P) to the
Headboard and Footboard. The
pockets in the Bed Rails should be
facing in and open to the top of the
Rails.
Leave all bolts loose until
everything is attached. Then
tighten all bolts.
H-21
H-3
NOTE:
Rail pockets must
face the inside.
4

Insert Connector Slats (A-37-C) into the
pockets that have holes. Secure using
2 - 1/2” Bolts (H-21) and Cross Dowels
(H-3). Leave these loose at this time.
PLEASE RETIGHTEN
BOLTS
AFTER 30 DAYS
5
Next insert all Regular Slats (A-37),
then tighten the 2 - 1/2” Bolts (H-21).
H-3
H-21
6