kd frames Studio Bifold Queen 7721 User manual

PARTS
Instructions for
Studio Bifold
Queen #7721
Use a small hammer to tap
Wood Dowels (H-11) all the
way into holes as shown.
1
Manufactured by:
(2) K-62 SEAT SLAT- 76”
(2) K-2 SEAT RAIL- 37”
(7) K-64 MIDDLE SLAT - 72”
K-6L BACK LEG (Left) (1) K-6R BACK LEG (Right) (1)
K-2 SEAT RAIL (2)
K-65
K-4
H-19
2
(2) K-15 SEAT SLAT CAP - 20”
PARTS LIST
BACK RAIL
K-41 2
K-2 2
SEAT RAIL
2
PROP
K-4
K-65 1
PROP CONNECTOR
4
2
6
H-6
6
WASHER
K-64
MIDDLE SLATS
7
20
H-11
WOOD DOWEL
29
H-19
1-1/2” SCREW
2
K-6
BACK LEG (Left and Right)
2
K-7
SEAT LEG
K-62
2
SEAT SLATS
K-15
20” SEAT SLAT CAPS
2
K-61
BACK SLATS
2
(2) K-7 SEAT LEG - 9”
(2) K-61 BACK SLAT - 76”
(1) K-65 PROP CONNECTOR - 60”
K-4 PROP (2)
K-41 BACK RAIL (2)
(2) K-4 PROP - 15”
(2) K-41 BACK RAIL- 34”
Press the Prop Connector (K-65)
onto the Wood Dowels on the
Props (K-4) and attach with
1-1/2” Screws (H-19).
1
K-10
SEAT SLAT SUPPORTS
(1) K-10 SEAT SLAT SUPPORT - 24”
K-4
NOTE:
The Prop Connector (K-65)
shown above is shortened
to save space.
1
K-18
BACK SLAT SUPPORTS
(1) K-18 BACK SLAT SUPPORT - 29”
(2) K-18 BACK SLAT CAP- 25”
K-18
25” BACK SLAT CAPS
2
H-8 2-1/4” CLEVIS PIN
H-5 HAIR PIN
H-12 3” CLEVIS PIN
394 Dairy Pak Rd. •Athens, GA 30607
kdframes.com • [email protected]
v. 309

K-6L
K-6R
H-12
H-12
H-8
Be sure that the Prop
Connector goes below
the Back Rails.
H-6
3
K-41H-5
Be sure that the Props
are on the inside of the
Back Rails.
4
Be sure that the Prop
Connector
is below the
Back Rails.
Attach the Left and Right
Back Legs (K-6) to the
outside of the Back Rails using
the 3” Cevis Pins (H-12).
Do not put on the Washers
and Hair Pins at this time.
5
Place the Seat Rails (K-2)
onto the 3” Clevis Pins and
secure with Washers (H-6)
and Hair Pins (H-5).
6
Attach the Back Rails (K-41) to the
outside of the PropAssembly.
Let the PropAssembly swing down
so that the Prop Connector can go
below the Back Rails.
Please double-check your work at
this time. Any error in this assembly
will cause serious problems later.
K-2
Make sure that the cut-away part of
the Back Legs face in so that they
will support the Back Rails.
K-2
Now put the Washers
and Hair Pins on the
3” Clevis Pins.
H-8
Wheels must
face toward
the inside.

10
Using (4) Middle Slats (K-64)
push the Wood Dowels
into the edge holes on
(2) Back Slat Caps (K-18).
Findthe(2)BackSlats(K-61)
andpushthemontothe
WoodDowelsontheSlatCaps.
K-61
11
Back
Slat Deck
Seat
Slat Deck
Push the Slat Decks
down onto the Wood
Dowels and attach with
Wood Screws (H-19).
H-19
K-18
K-64
Note:
Wood Screws are
self-tapping and do
not need pilot holes.
9
Using (3) Middle Slats (K-64)
push the Wood Dowels
into the edge holes on
(2) Seat Slat Caps (K-15).
K-62
K-15
K-64
8
Secure Seat and Back Legs
with Wood Screws (H-19).
(Thesescrewsareself-tapping
and do not need pilot holes.)
7
H-8
H-8
K-7
K-7
Make sure that the cut-away part of
theSeatLegs (K-7)face insothat they
will support the Seat Rails.
Attach the Seat Legs (K-7) to the
Seat Rails using 2-1/4” Clevis Pins (H-8).
Secure with Washers (H-6) and Hair Pins (H-5).
H-19
H-19
Findthe(2)SeatSlats(K-62)
andpushthemontothe
WoodDowelsontheSlatCaps.

Knockdown Frameworks, Inc. warrants all of its products for five years against any defects that are due to faulty
materials or workmanship. We will promptly correct such defects by repair or replacement, at our option, without
charge. This warranty covers product defects only and will expire five years after date of purchase by the original
consumer purchaser, with proof of purchase required.
This warranty does not apply to damage caused by and resulting from misuse, neglect, accident, or improper
operation,maintenance,storage,transportation,orhandlingoftheproduct. Thiswarrantyisfortheoriginalconsumer
purchaser for residential use only and does not apply if the product is used in any commercial application (such
as rental property). This warranty does not cover any incidental or consequential damages. If you feel that you have
a claim under this warranty, please contact the store from which it was purchased. If this is not possible, call 800-
543-3393 for advice on handling your claim.
This futon frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a few weeks.
This will happen in 20 to 30 minutes if placed in direct sunlight. Tulip Poplar can be left unfinished, clear finished,
stained, or painted. I prefer the lighter stains over the darker ones because the wood is fairly porous. My favorite
is a clear finish with no stain. Satin polyurethane (oil or water based) works well.
Painting: It is best to start with an interior primer and lightly sand before painting.
Staining: Lightly sand before staining. Wipe stain on with a rag until you get the desired color. If you are going to
use a top coat (such as polyurethane), do not sand again until after the first coat, and then be careful not to sand
away the stain.
Finishing: All finishes work well with Tulip Poplar. A simple wax finish over stain (Minwax for example) is easy.
An oil finish such as Danish oil can be used. Or a clear top coat such as polyurethane works well to seal the wood.
With polyurethanes, the first coat acts as a sanding sealer. So you should lighty sand (180 - 220 grit sandpaper)
after the first coat, wipe the wood clean, and then build up coats for the desired effect.
Operation:
Bed position:
Sofa position:
Lift up Back and swing
down Prop onto
notches on Seat Rail.
Adjust Back to a
comfortable position.
Sofa position:
12
Attach the Seat Slat Support (K-10) under the Seat Deck
and the Back Slat Support (K-18) under the Back Deck by
screwing (4) Wood Screws (H-19) down through the Slats
and into holes provided in the Slat Supports.
H-19
Then turn frame over and screw
(7) Wood Screws (H-19) through the
Slat Supports and into the Middle Slats.
(These are self-tapping screws so
no pilot holes are needed.)
H-19
K-18
K-10