kd frames Savannah 7212-SB-F User manual

(2) L-75-ST STRETCHERS (75”)
HARDWARE LIST
H-10 1
HEX WRENCH
H-8 6
2-1/4” CLEVIS PIN
H-9 4
PLASTIC ROLLER
H-3 24
CROSS DOWEL
H-5 2
HAIR PIN
H-21 2 - 1/2” BOLT 8
(2) L-27-B BACK END CAPS (27”)
(1) L-27-SR RIGHT SEAT END CAP (27”)
(2) L-72-BR BACK RAIL (72”)
(2) L-70-SR SEAT RAIL (70”)
(16) L-23 REGULAR SLAT (23”)
(4) L-23-CS CONNECTOR SLAT (23”)
Use 2-1/2” Bolts (H-21) and
Cross Dowels (H-3) to attach
two Connector Slats (L-23-CS)
between the Back Rails (L-72-BR).
Leave the bolts loose.
Place (8) Regular Slats (L-23)
into the pockets and
then tighten the bolts.
1
H-1 3” BOLT 16
L-2 LEFT ARM (1)
L-1 RIGHT ARM (1)
Note: Arms are packed in a seperate box.
Assemble Back
Press the Back End Caps (L-27-B) onto
the wood dowels and attach using
3” Bolts (H-1) and Cross Dowels (H-3).
Manufactured by
394 Dairy Pak Rd. • Athens, GA 30607
kdframes.com • [email protected]
Attach the Plastic Rollers (H-9) by
pushing a Clevis Pin (H-8) through the
small end of the Roller and into the holes
provided in the Back End Caps.
(These Clevis Pins do not need hair pins)
NOTE:
Place the best looking
Back Rail on this side to
make your frame look its
best.
PARTS LIST
Savannah
sku# 7212-SB-F
Assembly Instrucons
Size Full
(1) L-27-SL LEFT SEAT END CAP (27”)

2
H-1
H-3
Assemble Seat
Use 2-1/2” Bolts (H-21) and
Cross Dowels (H-3) to attach
two Connector Slats (L-23-CS)
between the Seat Rails (L-70-SR)
Leave the bolts loose.
Place (8) Regular Slats (L-23)
into the pockets and
then tighten the bolts.
Make sure that the Seat Locks are
facing down as shown and press the
Left Seat End Cap (L-27-SL) and
Right Seat End Cap (L-27-SR) onto the
wood dowels and attach using
3” Bolts (H-1) and Cross Dowels (H-3).
NOTE:
Place the best looking
Seat Rail on this side to
make your frame look its
best.
NOTE:
Seat Locks
face down
Assemble Frame
Use 3” Bolts (H-1) and
Cross Dowels (H-3) to attach
the Stretchers (L-75-ST)
to the Arms (L-1 and L-2)
Leave the bolts loose.
NOTE:
Place the best looking
Stretcher on this side to
make your frame look its
best.
NOTE:
Roller slots
face in
3
Right Seat End Cap
L-27-SR
Left Seat End Cap
L-27-SL

45
H-8
H-5
H-8
Attach Back Attach Seat
Carefully install Back by placing the
four Plastic Rollers into the four slots.
Make sure that all four Plastic Rollers
are in the four different slots, and then
tighten the Stretcher Bolts.
Place the four Plastic
Rollers in four slots.
Tighten Bolts after the
Rollers are in the
slots.
Slide the Seat End Caps in
between the Back End Caps.
Line up the holes by looking
through the hole in the Back End Cap.
Push the Clevis Pins (H-8) through the
Back End Cap and the Seat End Cap
and secure them with the Hair Pins (H-5).

Knockdown Frameworks, Inc. warrants all of its products for five years against any defects that are due
to faulty materials or workmanship. We will promptly correct such defects by repair or replacement, at our
option, without charge. This warranty covers product defects only and will expire five years after date of
purchase by the original consumer purchaser, with proof of purchase required.
This warranty does not apply to damage caused by and resulting from misuse, neglect, accident, or
improper operation, maintenance, storage, transportation, or handling of the product. This warranty is for
the original consumer purchaser for residential use only and does not apply if the product is used in any
commercial application (such as rental property). This warranty does not cover any incidental or
consequential damages. If you feel that you have a claim under this warranty, please contact the store
from which it was purchased. If this is not possible, call 706-543-9397 for advice on handling your claim.
Operation:
To convert to bed:
Lift up front of Seat to release
Seat lock and gently pull forward.
To convert to sofa:
Lift up Back and push forward.
This futon frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a few
weeks. This will happen in 20 to 30 minutes if placed in direct sunlight. Tulip Poplar can be left
unfinished, clear finished, stained, or painted. I prefer the lighter stains over the darker ones because
the wood is fairly porous. My favorite is a clear finish with no stain. Satin polyurethane (oil or water
based) works well.
Painting: It is best to start with an interior primer and lightly sand before painting.
Staining: Lightly sand before staining. Wipe stain on with a rag until you get the desired color. If you
are going to use a top coat (such as polyurethane), do not sand again until after the first coat, and then
be careful not to sand away the stain.
Finishing: All finishes work well with Tulip Poplar. A simple wax finish over stain (Minwax for example)
is easy. An oil finish such as Danish oil can be used. Or a clear top coat such as polyurethane works
well to seal the wood. With polyurethanes, the first coat acts as a sanding sealer. So you should lighty
sand (180 - 220 grit sandpaper) after the first coat, wipe the wood clean, and then build up coats for the
desired effect.