kd frames Ekko Bed Full User manual

PARTS
1
Manufactured by
(4) E-1 BED RAIL - 37”
(6) E-31 MIDDLE SLAT - 48”
(4) E-3 SLAT CAP - 15”
2
PARTS LIST
BED RAIL
E-1 4
4
E-4
H-8 8
2-1/4” CLEVIS PIN
H-12 4
3-1/4” CLEVIS PIN
12
H-5
HAIR PIN
E-2
9” SLAT CAP
4
E-30
BED SLAT
816
H-19
1 - 3/4” WOOD SCREW
2
E-7
CENTER LEG
2
E-8
RAIL CONNECTOR
E-3
15” SLAT CAP
4
E-31
MIDDLE SLAT
6
Knockdown Frameworks, Inc. warrants all of its products for five years against any defects that are due to faulty
materials or workmanship. We will promptly correct such defects by repair or replacement, at our option, without
charge. This warranty covers product defects only and will expire five years after date of purchase by the original
consumer purchaser, with proof of purchase required.
This warranty does not apply to damage caused by and resulting from misuse, neglect, accident, or improper
operation, maintenance, storage, transportation, or handling of the product. This warranty is for the original
consumer purchaser for residential use only and does not apply if the product is used in any commercial application
(such as rental property). This warranty does not cover any incidental or consequential damages. If you feel that you
have a claim under this warranty, please contact the store from which it was purchased. If this is not possible, call
800-543-3393 for advice on handling your claim.
(2) E-7 RAIL CONNECTOR - 7.5”
(8) E-30 BED SLAT - 52”
(4) E-2 SLAT CAP - 9”
Assemble the 1-Slat Decks by
pressing (1) Middle Slat (E-31)
into (2) Slat Caps (E-2).
Then press (2) Bed Slats (E-30)
onto the Slat Caps.
Repeat for the other 1-Slat Deck.
E-2
E-31
(2) E-8 CENTER LEG - 13”
E-3
E-31
This bed frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a few
weeks. This will happen in 20 to 30 minutes if placed in direct sunlight. Tulip Poplar can be left unfinished,
clear finished, stained, or painted. I prefer the lighter stains over the darker ones because the wood is fairly
porous. My favorite is a clear finish with no stain. Satin polyurethane (oil or water based) works well.
Painting: It is best to start with an interior primer and lightly sand before painting.
Staining: Lightly sand before staining. Wipe stain on with a rag until you get the desired color. If you are
going to use a top coat (such as polyurethane), do not sand again until after the first coat, and then be
careful not to sand away the stain.
Finishing: All finishes work well with Tulip Poplar. A simple wax finish over stain (Minwax for example) is
easy. An oil finish such as Danish oil can be used. Or a clear top coat such as polyurethane works well to
seal the wood. With polyurethanes, the first coat acts as a sanding sealer. So you should lighty sand (180 -
220 grit sandpaper) after the first coat, wipe the wood clean, and then build up coats for the desired effect.
Instructions for
Ekko Bed
Full
END LEG
(4) E-4 END LEG - 12”
Assemble the 2-Slat Decks by
pressing (2) Middle Slats (E-31)
into (2) Slat Caps (E-3).
Then press (2) Bed Slats (E-30)
onto the Slat Caps.
Repeat for the other 2-Slat Deck.
E-30 E-30
394 Dairy Pak Rd. • Athens, GA 30607
kdframes.com • [email protected]
(2) E-44 LEG CONNECTOR - 44”
2
E-44
LEG CONNECTOR
H-1 4
3” BOLT
4
H-3
CROSS DOWELL
1
H-10 “Z” WRENCH
v. 111
sku# 7912-EK-F

6
5
H-19
H-5
H-8
H-8
E-7
From Step 3
From Step 3
From Step 4
From Step 4
Use (4) 2-1/4” Clevis Pins (H-8)
to Attach (2) Bed Rails (E-1) to
each Leg Assembly (from Step 3).
Use the Center Legs (from Step 4)
to attach the two parts of the
bed together by pushing the
Clevis Pins into the holes on
the ends of the Bed Rails.
Slide the Rail Connectors (E-7)
onto the 3-1/4” Clevis Pins.
Secure all of the Clevis Pins with
Hair Pins (H-5).
Push the Slat Decks down
onto the wood dowels
and attach with
Wood Screws (H-19).
Note:
Wood Screws are
self tapping and do
not need pilot holes.
1 Slat Deck
2 Slat Deck
2 Slat Deck
H-3
E-4
E-4
H-1
E-44
3
Press an End Leg (E-4) onto
the Wood Dowels on each end
of a Leg Connector (E-44).
Attach the End Legs with
3” Bolts (H-1) and Cross Dowels (H-3).
Repeat for the other Leg Assembly.
Note:
Be sure that the two
holes are on the top.
Insert 2 of the 3-1/4” Clevis Pins (H-12) into
the holes on each of the 2 Center Legs (E-8).
Note:
The Clevis Pins must be inserted into the
side with the larger holes and pushed in
as far as possible.
Large holes
on this side
H-12
E-8
4
1 Slat Deck
E-1
E-1
E-1
E-1