kd frames 7902-TR-F User manual

Tool Required: #2 Phillips-Head Screwdriver.
2
Manufactured by
(4) N-70 BED RAILS (70”)
(16) N-23 REGULAR SLATS (23”) (4) N-22 CONNECTOR SLATS (23”)
(2) N-52 END CONNECTORS (52”)
Use 2-1/2” Bolts (H-21) and
Cross Dowels (H-3) to attach
Bed Rails (N-70) and
Connector Slats (N-22).
Leave the bolts loose until Step 2.
Place Regular Slats (N-23)
into the pockets and
then tighten the bolts.
Repeat Steps 1 and 2 for
the other Bed Deck.
1
Parts
H-21
H-3
NOTE: Bolts should be
just loose enough to
insert the Regular Slats.
NOTE: When the Slats
are all in their pockets,
tighten the bolts.
HARDWARE LIST
1
H-10 HEX WRENCH
H-3 CROSS DOWEL
16
8
H-21 2 - 1/2” BOLT
8
H-1 3” BOLT
Instructions for
Trundle Bed
Full 394 Dairy Pak Rd. • Athens, GA 30607
kdframes.com • [email protected]
WHEELS
H-W
4
H-34 3/4” WOOD SCREWS
8
sku# 7902-TR-F

Knockdown Frameworks, Inc. warrants all of its products for five years against any defects that are due to faulty materials or workmanship. We will promptly correct such
defects by repair or replacement, at our option, without charge. This warranty covers product defects only and will expire five years after date of purchase by the original
consumer purchaser, with proof of purchase required.
This warranty does not apply to damage caused by and resulting from misuse, neglect, accident, or improper operation, maintenance, storage, transportation, or handling
of the product. This warranty is for the original consumer purchaser for residential use only and does not apply if the product is used in any commercial application (such as
rental property). This warranty does not cover any incidental or consequential damages. If you feel that you have a claim under this warranty, please contact the store from
which it was purchased. If this is not possible,call 800-543-3393 for advice on handling your claim.
PLEASE RETIGHTEN
BOLTS
AFTER 30 DAYS
4
This futon frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a few weeks. This will happen in 20 to 30
minutes if placed in direct sunlight. Tulip Poplar can be left unfinished, clear finished, stained, or painted. I prefer the lighter stains over the darker
ones because the wood is fairly porous. My favorite is a clear finish with no stain. Satin polyurethane (oil or water based) works well.
Painting: It is best to start with an interior primer and lightly sand before painting.
Staining: Lightly sand before staining. Wipe stain on with a rag until you get the desired color. If you are going to use a top coat (such as
polyurethane), do not sand again until after the first coat, and then be careful not to sand away the stain.
Finishing: All finishes work well with Tulip Poplar. A simple wax finish over stain (Minwax for example) is easy. An oil finish such as Danish oil can
be used. Or a clear top coat such as polyurethane works well to seal the wood. With polyurethanes, the first coat acts as a sanding sealer. So
you should lighty sand (180 - 220 grit sandpaper) after the first coat, wipe the wood clean, and then build up coats for the desired effect.
ATTENTION!!
Make sure that the wheels
are on the lower, inside
edge of the End Connector
Make sure that the Wheels are
on the lower, inside edge of the
End Connector and then press
it onto the Bed Rails.
Attach with 3” Bolts (H-1) and
Cross Dowels (H-3) as shown.
H-3 H-1
Attach two Wheels (H-W) to one of the
the End Connectors (N-52) using four
of the the 3/4” Wood Screws (H-34).
Repeat for the other End Connector.
3
H-W
H-34